|
|
04-28-2009, 04:22 PM
|
|
SWCA Member
|
|
|
Join Date: Oct 2007
Location: South Africa
Posts: 241
Likes: 121
Liked 189 Times in 40 Posts
|
|
I am looking for a revolver that will last a long time with use of standard pressure ammunition and which will be easy to repair if something goes wrong.
I am not in the US and qualified gun smiths (with revolver experience)are hard to find. If I have a copy of Jerry Kuhnhausen's book and a supply of spare parts will the S&W model 10 be simple to maintain?
For a Model 10-6, which spare parts would you consider essential to keep the gun functioning in years to come after extensive use.
Thanks, Racingsnake
__________________
SWCA Membership Nr 3833
|
04-28-2009, 04:22 PM
|
|
SWCA Member
|
|
|
Join Date: Oct 2007
Location: South Africa
Posts: 241
Likes: 121
Liked 189 Times in 40 Posts
|
|
I am looking for a revolver that will last a long time with use of standard pressure ammunition and which will be easy to repair if something goes wrong.
I am not in the US and qualified gun smiths (with revolver experience)are hard to find. If I have a copy of Jerry Kuhnhausen's book and a supply of spare parts will the S&W model 10 be simple to maintain?
For a Model 10-6, which spare parts would you consider essential to keep the gun functioning in years to come after extensive use.
Thanks, Racingsnake
__________________
SWCA Membership Nr 3833
|
04-28-2009, 04:27 PM
|
Member
|
|
|
Join Date: Nov 2007
Location: west coast
Posts: 1,486
Likes: 0
Liked 55 Times in 34 Posts
|
|
Hi, Racingsnake!
The S&W Model 10, as well as the entire range of models built on the J, K, L, and N frame are extremely durable and trouble-free. If you insist on keeping spare parts, the ones you need are a set (3) of sideplate screws, a hammer nose ("firing pin") and rivet. Even with these spare parts, it's extremely unlikely that you will ever use them.
|
04-28-2009, 04:36 PM
|
|
Member
|
|
|
Join Date: May 2003
Location: DUNNELLON, FLORIDA USA
Posts: 11,113
Likes: 1,691
Liked 16,318 Times in 4,239 Posts
|
|
Hi:
I purchased My Model 10 4" barrel with Square Butt Blued Finish in 1963. I have had negative problems with it. I have used nothing but Standard Veocity Ammo in it.
I am not a proponent of Plus-P Ammo. I from the school of "If you need/want more power go to a larger caliber".
Jimmy
|
04-28-2009, 04:51 PM
|
|
Member
|
|
|
Join Date: Jul 2008
Location: Portsmouth, VA.
Posts: 1,402
Likes: 0
Liked 79 Times in 27 Posts
|
|
I don't think you could ware it out. I know people that have put thousands of rounds through them and was not able to ware them out.
__________________
May God Bless The USA
|
04-28-2009, 04:57 PM
|
Member
|
|
|
Join Date: May 2004
Location: South Eastern TN USA
Posts: 736
Likes: 0
Liked 17 Times in 8 Posts
|
|
Go ahead and get the spare parts mentioned above. Your grandchild may, repeat may, need them. The Model 10 is very durable.
__________________
195th Session FBINA
|
04-28-2009, 04:59 PM
|
|
SWCA Member
|
|
|
Join Date: Oct 2007
Location: South Africa
Posts: 241
Likes: 121
Liked 189 Times in 40 Posts
|
|
Thank you guys for your information - it's a revolver that inspires a lot of confidence. If it became necessary to replace a part such the bolt would it be possible for me to do so and reset the timing (using Kuhnhausen's book etc) or is it really something that needs to be attended to by a gunsmith?
Racingsnake
__________________
SWCA Membership Nr 3833
|
04-28-2009, 06:42 PM
|
|
US Veteran
|
|
|
Join Date: Jul 2007
Location: USA
Posts: 1,092
Likes: 8,577
Liked 1,656 Times in 600 Posts
|
|
The only part I've ever had to replace on a S&W revolver is the thumbpiece (used to open the cylinder). I was new to firearms and I failed to ensure the screw was tight.
If I could only have one centerfire handgun, I think it would be my model 10.
|
04-28-2009, 06:51 PM
|
|
Member
|
|
|
Join Date: Nov 2004
Location: Mountain State
Posts: 3,568
Likes: 56
Liked 379 Times in 149 Posts
|
|
The model ten was the second hand ejector made. So since 1899 they have been around. If you get a model 10 no - thur 10-8 will give you a revolver for a life time. Even used parts will be around for the next fifty years, so if you are twenty your great grand son will be able to find parts for it. Heck they will be shooting ray-guns by then .
|
04-28-2009, 07:32 PM
|
|
Member
|
|
|
Join Date: Oct 2000
Location: The Great State of Texas
Posts: 5,057
Likes: 524
Liked 1,909 Times in 788 Posts
|
|
Is it possible for you to buy two? The chances of two going bad are about 1 in 1,000,000. Even if something went wrong, you could use one for spare parts.
__________________
Centennial Every Day
|
04-28-2009, 07:33 PM
|
Member
|
|
|
Join Date: Nov 2007
Location: S.E.PA.
Posts: 1,908
Likes: 0
Liked 99 Times in 29 Posts
|
|
The "worn out" Smiths I have bought in the past, Usually just a new hand or a cylinder stop and a good cleaning are all they needed.
Peter
__________________
Need 1/2 moon Chiefs special
|
04-29-2009, 02:44 AM
|
|
Member
|
|
|
Join Date: Jul 2008
Location: Portsmouth, VA.
Posts: 1,402
Likes: 0
Liked 79 Times in 27 Posts
|
|
Humm? Ray guns. That would solve the ammo crisis. just plug it in for a recharge.
__________________
May God Bless The USA
|
04-29-2009, 03:09 AM
|
Member
|
|
|
Join Date: Nov 2007
Location: west coast
Posts: 1,486
Likes: 0
Liked 55 Times in 34 Posts
|
|
For correcting the common issues of excessive endshake or slight failure-to-carry-up, amatuer gunsmithing is enough. A new M10 would require firing tens of thousands of rounds of factory standard velocity ammunition to get to the point where it might need some attention.
The one thing that will help assure continued trouble-free operation is to remove the extractor rod, cylinder release screw, and mainspring tension screws, and reinstall using a tiny dab of blue Locktite thread sealant. Loosening or loss of these screws and the sideplate screws and the extremely rare broken hammer nose striker are the only maintenance points in this design. For adjustable rear sight models, occasional loss of the rear sight is possible due to loosening of the forward retaining screw.
|
04-29-2009, 12:31 PM
|
Member
|
|
|
Join Date: Sep 2004
Location: Wyoming
Posts: 3,259
Likes: 1,224
Liked 2,526 Times in 1,043 Posts
|
|
I have "a couple" of Vivas' M&Ps from the early 50s, and worked on others of the same vintage. Ditto the blue loctite. Otherwise it's just a matter of basic maintenance forever. I don't have any hammer noses or rivets but that's about the only thing I could imagine going out on these guns. Probably about the most trouble-free "machines " ever made.
|
04-29-2009, 02:19 PM
|
|
Member
|
|
|
Join Date: Mar 2003
Location: DFW TX
Posts: 425
Likes: 0
Liked 34 Times in 16 Posts
|
|
Welcome to the best forum on the internet. A good condition model 10 will serve you well for years to come. Be sure to check for buggered screws and hammer pushoff.
|
04-29-2009, 02:50 PM
|
|
SWCA Member
|
|
|
Join Date: Dec 2008
Posts: 6,898
Likes: 736
Liked 1,211 Times in 740 Posts
|
|
i have had my model 10 snub since 1975...purchased new it was $90.00
my son has it now....it has many rounds thru it..has been carried a lot...no issues,no repairs,nothing except cleaning...you will be pleased with your purchase...i certainly have been
__________________
SWCA#2208
KK4EMO
|
04-29-2009, 03:13 PM
|
US Veteran Absent Comrade
|
|
|
Join Date: Mar 2005
Location: Texas
Posts: 20,361
Likes: 24,260
Liked 16,154 Times in 7,408 Posts
|
|
The stainless version, Model 64, is even better. Far less rust issues, and if it gets scuffed, you can often polish it out.
Where do you live? Will a .38 suffice for all your needs?
How bad are the gun laws there?
T-Star
|
04-29-2009, 03:57 PM
|
Member
|
|
|
Join Date: Feb 2008
Location: Houston, TX
Posts: 121
Likes: 40
Liked 33 Times in 5 Posts
|
|
I saw it in a previous post on this thread, what is "hammer push off"?
|
|
Posting Rules
|
|
|
|
|