|
|
09-19-2009, 11:51 PM
|
Member
|
|
|
Join Date: Mar 2009
Location: Arkansas
Posts: 18
Likes: 0
Liked 1 Time in 1 Post
|
|
Hard to Open Cylinder
I have a Mod. 29-2 that has a cylinder that is difficult to open. It takes a bit of maneuvering but it will open. I haven't fired it since I acquired it. Everything else works fine. What is my problem?
__________________
NRA Life member.
|
09-19-2009, 11:58 PM
|
Member
|
|
|
Join Date: Aug 2008
Location: Colorado
Posts: 392
Likes: 5
Liked 60 Times in 44 Posts
|
|
Perhaps a bent ejector rod. Open it up and watch the ejector as you slowly rotate the cylinder.
|
09-20-2009, 12:07 AM
|
Member
|
|
|
Join Date: Sep 2009
Location: ARIZONA
Posts: 3,531
Likes: 3,518
Liked 6,263 Times in 1,970 Posts
|
|
Agreed. I was having the same problem with a 681. The rod was bent just enough to cause ocassional binding, but wasn't really obvious.
|
09-20-2009, 04:41 AM
|
Member
|
|
|
Join Date: Nov 2007
Location: west coast
Posts: 1,486
Likes: 0
Liked 55 Times in 34 Posts
|
|
When a revolver developes excessive endshake, the clearance between the end of the ejector rod and the forward locking bolt changes, often enough to make the tip of the locking bolt snag on the end of the ejector rod.
When you press and hold the cylinder release, check the end of the ejector rob as you open the cylinder. Is the end of the inner extractor pin flush with the end of the ejector rod? If not, those few thousandths of an inch below flush may be enough to snag the tip of the locking bolt, making for hard opening.
The fix is to correct the excessive endshake and/or refit the end of the extractor rod.
|
09-20-2009, 06:14 AM
|
|
Member
|
|
|
Join Date: May 2004
Location: Connecticut, USA
Posts: 1,525
Likes: 0
Liked 145 Times in 48 Posts
|
|
Like John says, but another thought, Did it unscrew?
__________________
NRA Benefactor Member
|
The Following User Likes This Post:
|
|
09-20-2009, 07:39 AM
|
|
Member
|
|
|
Join Date: Oct 2008
Location: Maine
Posts: 3,289
Likes: 3,076
Liked 3,829 Times in 851 Posts
|
|
Quote:
Originally Posted by 500 Magnum Nut
Like John says, but another thought, Did it unscrew?
|
Had that problem with my 360J just the other day. I had noticed it feeling like the cylinder might have been hanging up a bit and while fiddling with it, opening and closing it several times, the problem got progressively worse until it got stuck and felt like it was going to stay that way. I got it open one last time and found that the ejector rod had unscrewed to the point that it was hanging up. Luckily I hadn't bent it. I screwed it back in tight and now it's fine. Of course it took me a minute to figure out that the threads were reversed!
|
09-20-2009, 11:02 AM
|
Member
|
|
|
Join Date: Mar 2009
Location: Arkansas
Posts: 18
Likes: 0
Liked 1 Time in 1 Post
|
|
Thanks...I'll try that and let you know.
__________________
NRA Life member.
|
09-20-2009, 01:25 PM
|
|
US Veteran
|
|
|
Join Date: Aug 2006
Location: West Central IL
Posts: 22,802
Likes: 18,549
Liked 22,420 Times in 8,275 Posts
|
|
One other thing to check is if you have had the side plate off. If you mixed up the front screw and the middle screw it could be the cause. The front screw holds the cylinder crane from sliding out of the frame. The front screw is fitted, and if you put the center screw in it may be too long causing it to bind the crane. Swap the screws and it will be fixed (if that is the problem).
__________________
H Richard
SWCA1967 SWHF244
|
09-20-2009, 03:31 PM
|
Member
|
|
|
Join Date: Mar 2009
Location: Arkansas
Posts: 18
Likes: 0
Liked 1 Time in 1 Post
|
|
The cylinder screw had almost unscrewed itself. Thanks to all who answered. That's the first time I have ever had that happen and I carried a Smith & Wesson revolver for almost 9 years. I went ahead and cleaned and re-oiled everything and it now works perfectly. Thanks again!
__________________
NRA Life member.
|
08-01-2017, 07:13 PM
|
Member
|
|
|
Join Date: Mar 2013
Location: Ft. Wayne, Indiana
Posts: 5
Likes: 1
Liked 1 Time in 1 Post
|
|
I also have a Smith 29-2 with same issue of hard to open cylinder. With this one it seems to make it easier if you push the cylinder rearward as you perform the opening cylinder attempt. I have checked the ejector rod for tighten and it is, found no burrs on any obvious area but still requires that slight cylinder push rearward. Any suggestions would be greatly appreciated as its gettin frustrating at this point. Thanks
|
08-01-2017, 09:43 PM
|
|
US Veteran
|
|
|
Join Date: Jul 2013
Location: Southwest Iowa
Posts: 10,867
Likes: 2,688
Liked 18,970 Times in 5,589 Posts
|
|
I always make sure the ejector rod is tight.
__________________
Mike
S&WCA #3065
|
08-01-2017, 10:18 PM
|
Member
|
|
|
Join Date: Feb 2006
Posts: 3,425
Likes: 1,105
Liked 5,152 Times in 1,580 Posts
|
|
Quote:
Originally Posted by Targets Guy
I always make sure the ejector rod is tight.
|
That would be the first thing to check.
|
08-02-2017, 02:27 AM
|
|
Member
|
|
|
Join Date: Dec 2012
Location: N.E. OKLA.
Posts: 6,484
Likes: 5,882
Liked 9,332 Times in 3,497 Posts
|
|
Quote:
Originally Posted by djenk201
I also have a Smith 29-2 with same issue of hard to open cylinder. With this one it seems to make it easier if you push the cylinder rearward as you perform the opening cylinder attempt.
|
You should not be able to push the cylinder rearward ideally. Sounds like your 29-2 has some end shake. IIRC, this causes the center pin to be too far forward & the cylinder latch doesn't have enough range to fully release it.
Mine developed end shake that necessitated adding (2) .002" bearing/shims to eliminate it. The center pin's spring naturally tries to push the cylinder forward, taking up that clearance/gap between the end of the yoke barrel & the cylinder, which is overcome when you push it rearward.
Measure the B-C gap with the cylinder held forward & then with it held rearward. The difference is it's end shake. Anything over .002" should be repaired. (Mine was .004") With it repaired you should barely notice any rearward movement (~.001"). You can buy the bearings/shims at MidwayUSA.
As I recall my 29-2 cylinder was a little hard to open too, like you describe, when I noticed the end shake. Afterwards it's okay.
.
__________________
Waiting for the break of day
Last edited by BLUEDOT37; 08-02-2017 at 02:32 AM.
Reason: .
|
|
Posting Rules
|
|
|
|
|