|
|
05-15-2012, 08:08 PM
|
|
Member
|
|
|
Join Date: Dec 2010
Location: Columbus, Indiana
Posts: 387
Likes: 179
Liked 72 Times in 53 Posts
|
|
Painting Front Sight on Revolver
I've just about decided that the front sights on my 64, 637 and 642 are going to get a base coat of white Testor's enamel, topped with either fluorescent orange or fluorescent green. My question is how much of each sight to paint. Do most people paint the entire grooved portion of the ramp or just the the upper 1/4" or so?
Last edited by Hurryin' Hoosier; 05-15-2012 at 09:42 PM.
|
The Following User Likes This Post:
|
|
05-15-2012, 08:21 PM
|
Member
|
|
|
Join Date: May 2012
Location: Charlotte NC
Posts: 86
Likes: 22
Liked 35 Times in 10 Posts
|
|
I have been coloring mine with a grease pencil in either red or white And I do the complete length.
|
05-15-2012, 08:54 PM
|
Member
|
|
|
Join Date: Aug 2003
Location: Occupied California
Posts: 2,792
Likes: 1,524
Liked 5,587 Times in 1,612 Posts
|
|
Before I painted the front sight on my Model 65, I experimented with a piece of that blue painters masking tape. You will want to paint all the way up to the top serration before the part where blade turns to smooth. But to figure out how low to paint, place the edge of the tape at various points close to the lowest serration and take a good sight picture. You can figure out what the lowest serration is that is visible at the bottom of the rear sight notch pretty quickly. Then count how many serrations up from the bottom to start and paint the area between that serration and the top serration.
|
The Following User Likes This Post:
|
|
05-15-2012, 10:57 PM
|
|
Member
|
|
|
Join Date: Jul 2006
Location: New Mexico & Arizona
Posts: 1,630
Likes: 735
Liked 1,460 Times in 644 Posts
|
|
I've been using red nail polish for decades. Paint the entire length. Works greats and last a long time.
__________________
Support your Police, & NRA
|
05-16-2012, 02:09 PM
|
Member
|
|
|
Join Date: Sep 2007
Posts: 220
Likes: 0
Liked 33 Times in 20 Posts
|
|
If your concern is being able to see the front sight in low light use yellow. Tests conducted by the insurance industry have shown that yellow is seen by the human eye better than any other color as the light source is reduced. This is the reason most fire departments are now painting the trucks lime green or yellow instead of red. Bright fluorescent colors seem like a good idea but on an outdoor range in bright sunlight where the sun is off to one side of you it can glare so fiercely on one side it will make you pull your sights off to the sunny side. I settled on yellow years ago and haven't found anything that works better in sunlight or low light. I also found that a small dot applied with a toothpick works better than painting the entire width of the blade. You just need a small reference point for your eye to center in the rear notch.
Last edited by Drail; 05-16-2012 at 02:11 PM.
|
The Following 3 Users Like Post:
|
|
05-16-2012, 03:06 PM
|
Member
|
|
|
Join Date: Mar 2005
Location: Florida
Posts: 99
Likes: 131
Liked 53 Times in 29 Posts
|
|
I to use a toothpick to apply a Neon Orange acrylic paint to the upper half of my front sights after first cleaning the sight with alcohol. After two or three coats have dried I then apply two coats of clear nail hardener from my wife's nail stuff. This makes the final product rather durable. I get a 2 oz bottol of paint from the craft section of Walmart for around a dollar, also the shelf life is longer than the Testor paint I used before. There is also; Neon Green, Pink, etc.
Allow an hour or so between coats for the acrylic colored paint, the clear nail finish dries in 15 min.
|
The Following 2 Users Like Post:
|
|
05-16-2012, 04:35 PM
|
|
Member
|
|
|
Join Date: Jun 2010
Location: Michigan
Posts: 9,656
Likes: 1,362
Liked 1,371 Times in 699 Posts
|
|
I always paint all of the serrations but will come in one
serration on each end with my tape on my white, base coat(s).
For my "color" coats I do the serrations that I didn't get with the white
and do it this way just so I don't end up with white showing at the ends.
Basically it gives me a "cleaner looking" sight when I'm finished.
__________________
Ogy
Last edited by ogilvyspecial; 05-16-2012 at 06:27 PM.
|
The Following 3 Users Like Post:
|
|
05-17-2012, 01:39 AM
|
US Veteran
|
|
|
Join Date: Sep 2010
Location: New Iberia, Louisiana
Posts: 4,588
Likes: 25,427
Liked 3,380 Times in 1,736 Posts
|
|
Maybe I'm old fashioned but most of my handguns have the painted foresight. On the ones that do have a removable front sight I plan on getting one of the gold bead sights and see how it works. There has got to be something better than painting the whole of the ramp with paint. Frank
|
05-17-2012, 09:38 AM
|
Member
|
|
|
Join Date: Sep 2007
Posts: 220
Likes: 0
Liked 33 Times in 20 Posts
|
|
The gold or brass bead front sight is one of the best designs anyone ever came up with.
|
05-18-2012, 08:51 AM
|
|
Member
|
|
|
Join Date: Dec 2010
Location: Columbus, Indiana
Posts: 387
Likes: 179
Liked 72 Times in 53 Posts
|
|
Quote:
Originally Posted by ogilvyspecial
|
Did you break into my house? You've got a picture of my 642 and my Robert Mika pocket holster! (No - wait a minute - there's no Tyler T-Grip.)
|
The Following 2 Users Like Post:
|
|
05-18-2012, 09:08 AM
|
Member
|
|
|
Join Date: Jan 2012
Location: Baja Oklahoma
Posts: 25
Likes: 1
Liked 6 Times in 5 Posts
|
|
I don't have my 642 yet, but here is what I plan to use. I've used it lots on restoring watch dials.
Tom
|
05-18-2012, 09:38 AM
|
Member
|
|
|
Join Date: May 2012
Location: Long island, NY
Posts: 9
Likes: 5
Liked 0 Times in 0 Posts
|
|
I have heard of people painting gun sights. I have a S&W model 686 stainless that came with a front orange sight, but my other revolvers have the plain sights. I only know of one guy who did paint them and it didn't come out to good. He's a big gun buff, (some 40 guns) so he wasn't happy with the out come of it, so he took the gun to a dealer, who had some good advise for him. I don't know if i would try to paint my own sights, only because i would worry that the paint would not stick to the metal. This is a tough one! Good luck.
John
Quote:
Originally Posted by Hurryin' Hoosier
I've just about decided that the front sights on my 64, 637 and 642 are going to get a base coat of white Testor's enamel, topped with either fluorescent orange or fluorescent green. My question is how much of each sight to paint. Do most people paint the entire grooved portion of the ramp or just the the upper 1/4" or so?
|
|
05-18-2012, 09:49 AM
|
|
Member
|
|
|
Join Date: Jul 2003
Location: Ohio, USA
Posts: 1,379
Likes: 26
Liked 451 Times in 233 Posts
|
|
Testers 'DayGlo' orange works the best MOST of the time,but hey everyones eyes are different, see things differently ..........REMEMBER though when the sun is straight up, overhead, all of them bright colors tend to 'fade', then one "needs" contrast..............thats why there have been so many different cuts, angles,colors of sights over the years......
__________________
dan
NRA Benefactor,PMA
|
05-18-2012, 11:54 AM
|
Member
|
|
|
Join Date: Nov 2004
Location: Michigan, USA
Posts: 2,260
Likes: 2
Liked 116 Times in 85 Posts
|
|
I use fluorescent orange acrylic model paint and cover the equivalent of 1/8 in. vertical.
|
05-19-2012, 09:21 PM
|
Member
|
|
|
Join Date: Aug 2004
Location: Georgia,United States
Posts: 169
Likes: 7
Liked 41 Times in 16 Posts
|
|
This article has a lot of good information.
Improving Your Snubs Sights
|
05-19-2012, 09:37 PM
|
Member
|
|
|
Join Date: Aug 2003
Location: Occupied California
Posts: 2,792
Likes: 1,524
Liked 5,587 Times in 1,612 Posts
|
|
Here's a couple of pics of what I did with my Model 65-3. I like the idea of using fishing lure paint, I'll bet that is more durable than model airplane paint and next time I'll try that kind of paint. The article in the link from frankw is good, it explains why you should not paint the entire surface.
|
The Following User Likes This Post:
|
|
05-19-2012, 10:21 PM
|
Member
|
|
|
Join Date: May 2010
Posts: 156
Likes: 35
Liked 84 Times in 16 Posts
|
|
I use the paint especially designed for gun sights....comes in red, white, yellow, florescent orange and green. It works pretty well. I'm more concerned with being able to take it off if I ever decide to sell a gun than its indestructability--comes off with nail polish remover...no problem.
|
05-23-2012, 06:29 PM
|
|
Member
|
|
|
Join Date: Dec 2010
Location: Columbus, Indiana
Posts: 387
Likes: 179
Liked 72 Times in 53 Posts
|
|
Quote:
Originally Posted by frankw
|
Interesting article, but I'm not sure I agree with his logic on not painting the entire front ramp. (Besides, I've already painted the whole durn thing and I think it looks good and it's my gun so tthhppfftt!! )
|
06-23-2012, 11:21 AM
|
|
Member
|
|
|
Join Date: Jan 2009
Location: Knoxville, TN
Posts: 395
Likes: 75
Liked 87 Times in 29 Posts
|
|
Quote:
Originally Posted by ogilvyspecial
I always paint all of the serrations but will come in one
serration on each end with my tape on my white, base coat(s).
For my "color" coats I do the serrations that I didn't get with the white
and do it this way just so I don't end up with white showing at the ends.
Basically it gives me a "cleaner looking" sight when I'm finished.
|
I tried some fingernail polish on four of my guns and it was OK, but it wasn't very bright. I'm sure there are brighter ones available, but I decided to try the fishing lure and jig paint. I started with a 13-3 all black...
Then added two layers of white...
Then blaze orange...
And then I did a 642, 640-1 and a Ruger GP-100 3"...
I'm 80% satisfied with my work, but my eyes are getting old and I can't get it as perfect as the ones you guys are doing. However, when I hold it up and look down the barrel the front sight is extremely obvious. My old eyes do like that. So...I'm calling it a success for me - I like the fishing lure and jig paint. Best Wishes, B
|
The Following 9 Users Like Post:
|
|
06-24-2012, 05:20 PM
|
|
Member
|
|
|
Join Date: Apr 2006
Posts: 17,818
Likes: 7,852
Liked 25,737 Times in 8,695 Posts
|
|
The Testor's Blaze Orange is the way to go. You need not paint the full front sight, only about 3/8" is the part you will actually see while aiming. Use a factory red insert as a model to judge how much to paint.
BEFORE painting, use some alcohol to clean off any oil or solvent residue. Apply with a wooden toothpick and use 3 THIN coats rather than a gloppy thick one. Do not concern yourself if you get a little paint on the side of the sight, just clean it off with a razor after it is dried - comes right off. Make a simply jig to hold the gun in a horizontal position as the paint dries so it doesn't run.
Chief38
|
The Following User Likes This Post:
|
|
07-02-2012, 02:57 PM
|
|
Member
|
|
|
Join Date: Feb 2005
Location: On da Bayou Teche
Posts: 18,463
Likes: 18,569
Liked 58,919 Times in 9,675 Posts
|
|
Quote:
Originally Posted by AZretired
I've been using red nail polish for decades. Paint the entire length. Works greats and last a long time.
|
You ARE talking about the sights on your gun aren't you
__________________
Forum consigliere
|
The Following 6 Users Like Post:
|
|
07-24-2012, 10:34 PM
|
Member
|
|
|
Join Date: Mar 2012
Location: Iowa
Posts: 62
Likes: 11
Liked 17 Times in 9 Posts
|
|
I went to a hobby store
and bought a little bottle of hobby paint for under a buck a couple years ago and put it on the front sights of my rifles and my handguns with a toothpick. No need to spend big bucks on a some special paint I saw advertised recently for gun sights. I could not believe how much it cost. I have good luck with my 86 cent bottle of paint and if it occasionally wants to come off I have more in my shooting box. I am Mr. Frugal
|
08-08-2012, 07:54 AM
|
|
Member
|
|
|
Join Date: Aug 2012
Location: North Dakota
Posts: 10,146
Likes: 14,193
Liked 12,746 Times in 3,482 Posts
|
|
fishermans "jig head" paint for front sights
even better then Testors model paint is the paint fishermen use to paint their jig heads--comes in flourescent colors
|
08-08-2012, 08:03 AM
|
Member
|
|
|
Join Date: Dec 2009
Location: Northeast Ohio
Posts: 4,273
Likes: 3,043
Liked 1,791 Times in 932 Posts
|
|
Some say DO NOT PAINT the bottom 1/4 or 1/3 portion of the sight.
__________________
NRA Pistol/Rifle Inst. RSO
|
02-01-2013, 06:18 PM
|
Member
|
|
|
Join Date: Aug 2012
Posts: 72
Likes: 0
Liked 21 Times in 13 Posts
|
|
is this fisherman paint removable?
|
02-01-2013, 07:50 PM
|
|
Member
|
|
|
Join Date: Jun 2010
Location: Michigan
Posts: 9,656
Likes: 1,362
Liked 1,371 Times in 699 Posts
|
|
Quote:
Originally Posted by Davidnssbm
is this fisherman paint removable?
|
Yes, any paint thinner should do the trick.
There have been a few times that I either, didn't like the color that I had chosen,
or the end results, so I removed the paint and started over.
I've found that pipe cleaners, dipped in thinner, makes things easier
when removing the paint from the bottom of the serrations.
With that said, I rarely go that far because it's, generally, the white
base coat down at the very bottom of the serrations so there
is no reason to remove it all, just to reapply.
__________________
Ogy
|
02-01-2013, 08:47 PM
|
Member
|
|
|
Join Date: Aug 2012
Posts: 72
Likes: 0
Liked 21 Times in 13 Posts
|
|
awesome. I'm definitely gonna do this. Now where do I buy the damn stuff in person? Also, any thoughts on painting the rear sights a matte black so that the sight tip pops more? I'm thinking either that neon green or orange.
|
02-01-2013, 10:19 PM
|
Member
|
|
|
Join Date: Mar 2010
Posts: 22
Likes: 0
Liked 0 Times in 0 Posts
|
|
You can use white out. It will let you experment whith how much you want to cover and can be removed pretty easy.
|
02-02-2013, 01:01 AM
|
Member
|
|
|
Join Date: Dec 2010
Posts: 75
Likes: 9
Liked 4 Times in 4 Posts
|
|
I just ordered from jannsnetcraft. I got the white, blaze and I think a glow blaze. One day I was trying to shoot my nickel j-frame ane the sun reflection was awful. I couldn't see the sight at all. This should help.
|
02-02-2013, 06:13 PM
|
Member
|
|
|
Join Date: May 2011
Location: Piedmont NC
Posts: 288
Likes: 810
Liked 156 Times in 55 Posts
|
|
There is a company called "Brite Sights" that has several colors to choose from. It is easy to remove by peeling it off and applying another color. It has a rubbery feel to it. I have used it on many of my 1911's with the three white dot sights.
I use orange on the back sight, and yellow on the front. But you would only use it on front sight. Try different colors.
|
02-02-2013, 06:41 PM
|
Member
|
|
|
Join Date: Jun 2001
Location: Florence, Alabama, USA
Posts: 2,347
Likes: 40
Liked 1,397 Times in 773 Posts
|
|
The Brite Sights paint is rather pastel compared to model or lure paint.
I use Model Master Fluorescent Red that has a bit of orange cast in it.
|
02-03-2013, 02:05 PM
|
|
US Veteran
|
|
|
Join Date: Nov 2012
Location: Reno Nv
Posts: 13,405
Likes: 3,189
Liked 12,771 Times in 5,690 Posts
|
|
Since my M49 shoots a tad low, I do not paint to the very top of the sight, to bring the poa up a little, for when I am shooting at the range,for more hits on target at slow fire and
testing reloads.
|
09-04-2013, 01:23 AM
|
Member
|
|
|
Join Date: Jun 2013
Posts: 136
Likes: 5
Liked 71 Times in 31 Posts
|
|
I just tried this with some cheap nail polish, and made a mess of it when I removed the masking tape. How long do you wait for the stuff to dry between coats and before removing any masking tape? I did 1 base coat of white, 3 coats of bright orange, 1 coat of clear, all over the course of about 2 hours, and thought I'd given it plenty of time to dry, but I found when doing the top coat, that the orange was bleeding onto the brush and then after going for a swim, I removed the masking tape from one and half the polish came off with it.
Is this a multi-day process?...or something to do every couple hundred rounds while reloading?
|
09-04-2013, 05:17 AM
|
|
Member
|
|
|
Join Date: Apr 2006
Posts: 17,818
Likes: 7,852
Liked 25,737 Times in 8,695 Posts
|
|
I only paint the portion of the front sight that would normally have the plastic insert of a Factory job because painting more doesn't do anything and can not even be seen when sighting the revolver on a target. I use Testor's Blaze Orange and when I bought the bottle I left the cap off for a day or so to thicken up the mixture. Making it a little thicker results in less running. Instead of putting on a real thick coat, I usually apply 2 or 3 lighter coats and I like to "fill" the serration's on the sight which gives it a bolder, brighter finish and is easier to pick up. I use a toothpick (not a brush) to apply the paint and it lasts just about forever but IS totally reversible if desired. If a bunch of years down the road the finish gets "tired", simply apply a new coat!
|
09-04-2013, 09:09 AM
|
SWCA Member
|
|
|
Join Date: Jan 2013
Location: S/W Indiana
Posts: 1,500
Likes: 1,923
Liked 2,458 Times in 876 Posts
|
|
Painting front sights
I have a M-65 that I bought in 76.....I shot it extensively for years and competed with it in IPSC....along with a GI 1911A1...I painted both front sights with Testor's white....a lot of my IPSC matches were at night and we had high mass lighting to the rear....the front sights "jumped out" and were very easy to pick up visually.....both guns still wear that paint....and they have been used a LOT over the years....I even had SO's comment on the sights when they were watching me shoot a stage. I found that having the entire ramp painted helped me pick up the sight faster.
|
09-04-2013, 11:57 AM
|
US Veteran
|
|
|
Join Date: Oct 2010
Posts: 7,808
Likes: 4,240
Liked 15,206 Times in 4,162 Posts
|
|
Like many others my eyesight is not what it used to be. That said I only paint half the front sight with a base coat of white appliance touch-up, then blaze orange from WalMart. It give me a flash sight picture that works good at the range and almost everywhere else.
__________________
Old Cop
LEO (Ret.)
|
09-04-2013, 12:07 PM
|
Member
|
|
|
Join Date: Jan 2013
Location: Florida
Posts: 1,555
Likes: 312
Liked 1,741 Times in 746 Posts
|
|
Don't forget to get all pretti-fied up and paint your gun too.
Here's my Walther done in Walther baby blue.
|
09-04-2013, 12:08 PM
|
|
Member
|
|
|
Join Date: Jan 2013
Location: North Carolina, USA
Posts: 1,470
Likes: 1,342
Liked 1,961 Times in 664 Posts
|
|
I try to mimic the factory red ramp insert seen on S&W revolvers by just painting the first 3-4 ridges on the front sight. I make sure to mask the areas I don't want painted with painter's tape.
Also I recommend model paint by Testors which offers a color in "Fluorescent Red" that stands out better under low light settings than the factory orange.
__________________
Ephesians 6 (Armor of God)
|
09-04-2013, 12:59 PM
|
Member
|
|
|
Join Date: May 2010
Posts: 98
Likes: 123
Liked 15 Times in 11 Posts
|
|
I sure as heck have no idea what the lot of you are drinking or smoking, but when I lift up any of my revolvers to squeeze off a round, I sure as hell don't see any serations, either a big blob of black or a big blob of orange, must be something in the water, although there are some lines that seem to hold the paint on better...............Dan.
|
09-04-2013, 01:08 PM
|
|
Member
|
|
|
Join Date: Sep 2012
Location: western Washington
Posts: 2,647
Likes: 1
Liked 763 Times in 454 Posts
|
|
I've used white appliance touch-up paint as well as a white paint marker on my blue guns which seemed to work well. Not so much so on my stainless guns. I picked up some cheap reddish-orange nail polish at Walmart for use on those, but it didn't work too well-- not bright enough. I guess model paint or jig-and-lure paint would be better, I'll have to pick some up. I don't particularly like zombie green, but it seems like that might give more contrast than red orange or yellow.
|
09-05-2013, 11:51 PM
|
Member
|
|
|
Join Date: Jun 2013
Posts: 136
Likes: 5
Liked 71 Times in 31 Posts
|
|
After a couple of days of trial and error I've learned a bit. First of all, serated front sights are way easier to deal with. The first gun I did was my 1911 which had plain black sights with a serated ramp front. Unfortunately, the guns I really wanted to do are a pair of K frame target guns with non-serated black front sights. I'm not sure of the terminology for this type of sight, but the rear facing part of it is 90* up/down relative to the bore axis and flat other than some minor tool marks.
The "paint" I bought is cheap nail polish (Jordana) from K-Mart. I bought 523 Edgy (which is a sort of dark orange that I thought would be bright), 502 white, and clear. This stuff is really annoying to work with. It begins to dry and turns gummy in about a minute or so. It doesn't actually fully dry for quite a bit longer (an hour or more...wait till you think it's probably dry...then wait another hour or so). If I try putting on an additional coat before the first is absolutely dry, the prior coat comes off as I'm trying to apply the new coat.
After I was reasonably happy with the first two guns (1911, and K22), it occurred to me to mix the white (which I'd bought as a base coat) with the orange. Mixing these roughly 1:1 (2 drops of each in the cup of a empty tray of small pistol primers) produces a nice light/bright orange that looks much better than the orange on its own.
I've had better luck applying the polish with a flat wood toothpick than when I was trying to use the nail polish brushes...and with the mixed polish, using the brushes isn't really an option anyway.
I've been using blue painter's tape as masking tape to control how far down the flat front sights I paint. Before removing the tape, cut the border with a sharp knife. Otherwise, some portion of the polish is liable to come off with the tape
Acetone will remove any overpaint, errors, or everything if you're not happy with it. I've been very careful not to touch the wood grips after messing with the acetone. If your grips have any sort of finish or are any sort of plastic, the acetone is likely seriously bad news for those...don't get any on them. I have a swiss army knife with my finger print embedded in the plastic from 20 or so years ago when I was cleaning tape residue off one of the blades with acetone.
Last edited by njl; 09-06-2013 at 12:39 AM.
|
The Following User Likes This Post:
|
|
09-10-2013, 11:47 PM
|
|
Member
|
|
|
Join Date: Apr 2013
Location: Southern Utah
Posts: 1,787
Likes: 4,217
Liked 2,791 Times in 895 Posts
|
|
Mineral Oil will take off the paint and not harm the finish.
|
09-11-2013, 12:25 PM
|
|
Member
|
|
|
Join Date: Sep 2012
Location: western Washington
Posts: 2,647
Likes: 1
Liked 763 Times in 454 Posts
|
|
I think you mean mineral spirits. "Mineral oil" is used in airplane engines for break-in.
|
|
Posting Rules
|
|
|
|
|