Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > S&W-Smithing
o

Notices

S&W-Smithing Maintenance, Repair, and Enhancement of Smith & Wesson and Other Firearms.


Reply
 
Thread Tools Display Modes
  #1  
Old 07-24-2013, 10:44 AM
BruMatt BruMatt is offline
Member
Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter  
Join Date: May 2012
Location: Florida
Posts: 132
Likes: 6
Liked 27 Times in 20 Posts
Default Land diameter to Groove diameter

If I measure the land diameter in a S&W barrel with a pin gage, is there a standard depth in the grooves to then determine the groove diameter? With the odd number of grooves, it is difficult to measure a slug. An alternate test would be useful.
Reply With Quote
  #2  
Old 07-24-2013, 10:50 AM
OKFC05 OKFC05 is offline
Member
Land diameter to Groove diameter Land diameter to Groove diameter  
Join Date: Aug 2007
Location: Oklahoma
Posts: 8,158
Likes: 3,605
Liked 5,199 Times in 2,172 Posts
Default

You can slug it, wrap with a .001 gage, measure diameter, subtract .002".
__________________
Science plus Art
Reply With Quote
  #3  
Old 07-24-2013, 05:18 PM
jepp2 jepp2 is offline
Member
Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter  
Join Date: Feb 2010
Location: Rocky Mtns, CO
Posts: 986
Likes: 19
Liked 214 Times in 141 Posts
Default

Quote:
You can slug it, wrap with a .001 gage, measure diameter, subtract .002".
I agree 100% this should work, but I have tired it a number of times and never had accuracy.

This will work!

Reply With Quote
The Following 2 Users Like Post:
  #4  
Old 07-25-2013, 08:55 AM
BruMatt BruMatt is offline
Member
Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter  
Join Date: May 2012
Location: Florida
Posts: 132
Likes: 6
Liked 27 Times in 20 Posts
Default

I guess I didn't ask the question clearly. Is there any information available that states the "standard" groove depth (or land height) in S&W revolver barrels? Does this measurement change with different models, years, or is it supposed to be constant?
Reply With Quote
  #5  
Old 07-25-2013, 09:16 AM
OKFC05 OKFC05 is offline
Member
Land diameter to Groove diameter Land diameter to Groove diameter  
Join Date: Aug 2007
Location: Oklahoma
Posts: 8,158
Likes: 3,605
Liked 5,199 Times in 2,172 Posts
Default

There is a "nominal" dimension, but the whole point of measuring YOUR barrel is to see what it actually is. Does it seem worthwhile to measure bore and then estimate groove with a "nominal" dimension? What does that really tell you?
__________________
Science plus Art
Reply With Quote
  #6  
Old 07-25-2013, 01:52 PM
BruMatt BruMatt is offline
Member
Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter  
Join Date: May 2012
Location: Florida
Posts: 132
Likes: 6
Liked 27 Times in 20 Posts
Default

Well, as demonstrated by the picture above (micrometer) and the methods used to wrap the slug to measure one with an odd number of grooves, it is difficult to get a precise measurement. What I was hoping for was a comparative based on the internal bore (land) measurement. Without buying the expensive micrometer, I am not sure I have the correct diameter by cutting up a beer can and wrapping the slug. Using that method in my 44 Spl I come up with .429 for a groove diameter but using a pin guage thru the barrel I get .416 which is the bore, or land, diameter. A groove depth of .0065 seems like it would be too much so I am concerned I have an error. The obvious place to look is the least precise measurement, the groove diameter of .429. That is the background to my question.
Reply With Quote
  #7  
Old 07-25-2013, 06:17 PM
jepp2 jepp2 is offline
Member
Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter  
Join Date: Feb 2010
Location: Rocky Mtns, CO
Posts: 986
Likes: 19
Liked 214 Times in 141 Posts
Default

I always feel that slugging the bore is a very valuable step. I oil the bore well and use pure lead (muzzleloader swaged balls) to do this. I feel for tight spots as the ball passes through the bore (like where the barrel passes through the frame.

Next I take the lead slugs and check them in the cylinder throats. If they are larger than the throats and you can't press them through with light finger pressure, you are going to have problems. It means your throats are too small for the groove diameter. If they do pass through, use your pin gages to determine the throat diameter and use that for your bullet selection.

I have never read where anyone was successful in trying to use pin gages in the barrel and then by using a land height to determine the groove diameter. But you might be the first. When I played around with it, I just couldn't get an accurate measurement.

And if this doesn't discourage you, send them to Matt Dardas. He offers a free service to measure the groove diameter of your slugs for FREE! How can you beat that?
Reply With Quote
The Following 2 Users Like Post:
  #8  
Old 07-25-2013, 11:45 PM
Alk8944's Avatar
Alk8944 Alk8944 is online now
Member
Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter  
Join Date: Jan 2007
Location: Sandy Utah
Posts: 8,617
Likes: 1,554
Liked 8,615 Times in 3,452 Posts
Default

In a revolver the fit of the bullet to the cylinder throats is more important than knowing the groove diameter. Simply slug the throats and size to that diameter.

If the cylinder throats are smaller than groove diameter, and this is not uncommon, it doesn't matter what size you make your bullets they will be undersized before they even get to the barrel!

Do this. Slug the barrel and then try to pass the slug through the throats. If it passes easily, or with slight pressure, size your bullets to fit the throats. If it will not pass relatively easily through the throats (Use a new bore slug for each charge hole.) then the cylinder throats need to be enlarged until the bore slugs do pass with light pressure. It doesn't do you one d****d bit of good to know the barrel groove diameter if you don't know the other dimensions too!

Note: Never in the process do you have to measure the barrel slug as how it fits the cylinder is all that matters!
__________________
Gunsmithing since 1961
Reply With Quote
The Following 4 Users Like Post:
  #9  
Old 09-04-2013, 06:06 PM
pokute pokute is offline
Banned
Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter  
Join Date: Nov 2011
Posts: 153
Likes: 12
Liked 23 Times in 12 Posts
Default

I second (or third, or ???) that the cylinder throat diameter is the only thing you are ever going to be able to come to a conclusion about, so you should avoid buying bullets that are going to get swaged coming out of the cylinder.

The first time I went poking around trying to measure the bore of a revolver I was gobsmacked... The damn thing, that shoots like a laser, had an insane constriction where the barrel was screwed into the frame. After discovering the SAME THING on two more infallible shooters, I quit.

As long as the bullet passes into the barrel intact, it will (and of course I'm only talking about lead bullets that are getting a good solid push to a decent velocity) be the right size at the right time.

Speaking of Matt Dardas, his bullets are the only ones that have got me out to 150 yards from a 1911 with accuracy and punch. I'd swear that the low melting point lube is half the trick, it's a little like the slime that's on 22lr match bullets.
Reply With Quote
The Following User Likes This Post:
  #10  
Old 09-05-2013, 01:47 PM
BruMatt BruMatt is offline
Member
Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter Land diameter to Groove diameter  
Join Date: May 2012
Location: Florida
Posts: 132
Likes: 6
Liked 27 Times in 20 Posts
Default

Thanks for the update.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Bullet Diameter vs Ball End Diameter Question Sixtogo Reloading 8 05-15-2016 11:37 PM
.355 diameter 130 gr FMJ use? gordondewolf Reloading 8 05-15-2015 11:51 PM
Tricks for measuring groove diameter for S&W jepp2 Reloading 9 05-04-2012 12:28 PM
38 S&W diameter geoff40 Reloading 6 04-01-2012 12:17 AM
Model 39 Groove Diameter? Cyrano Smith & Wesson Semi-Auto Pistols 0 01-01-2011 05:54 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 03:51 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)