|
|
01-01-2017, 09:17 AM
|
Member
|
|
|
Join Date: Sep 2014
Location: indiana
Posts: 13
Likes: 9
Liked 2 Times in 1 Post
|
|
extractor pins 29-2
does anyone know where i can get extractor pins for a 29-2
|
01-01-2017, 09:52 AM
|
|
Moderator
|
|
|
Join Date: Nov 2015
Location: SE Michigan
Posts: 18,563
Likes: 8,401
Liked 17,174 Times in 5,626 Posts
|
|
Obvious question, did you try Numrich? I'm not sure that the dash designation means a lot either as I'm pretty sure the pins stayed unchanged.
__________________
So many S&W's, so few funds!!
|
The Following User Likes This Post:
|
|
01-01-2017, 12:21 PM
|
Member
|
|
|
Join Date: Feb 2012
Location: Yuma
Posts: 801
Likes: 176
Liked 436 Times in 261 Posts
|
|
Cylinder and Slide Shop
__________________
A Snider squibbed n the Jungle
|
01-01-2017, 04:45 PM
|
Member
|
|
|
Join Date: Sep 2014
Location: indiana
Posts: 13
Likes: 9
Liked 2 Times in 1 Post
|
|
i took your advice and tried numrich they were out of stock ill keep looking thanks
|
01-01-2017, 06:15 PM
|
|
Member
|
|
|
Join Date: Jan 2007
Location: Sandy Utah
Posts: 8,726
Likes: 1,578
Liked 8,850 Times in 3,530 Posts
|
|
Call Jack First. (Google it)
__________________
Gunsmithing since 1961
|
01-02-2017, 03:40 PM
|
|
Member
|
|
|
Join Date: Dec 2008
Location: USA
Posts: 583
Likes: 1,520
Liked 642 Times in 290 Posts
|
|
When all else fails, drill rod or (IIRC), #54 HSS drill bit fixed a 28 N frame more than once. Can't recall size exactly but the pressure fit has worked great for many years. Unless it's a show piece or all "original matters" gun, these are quick and usually easy to come across. First,Numerich or maybe Popperts are the goto as mentioned, I waited 3 months with S&W a couple years back and received wrong parts twice.
|
The Following User Likes This Post:
|
|
01-02-2017, 03:54 PM
|
SWCA Member
|
|
|
Join Date: Feb 2014
Location: VA & SoFL
Posts: 8,684
Likes: 472
Liked 5,731 Times in 3,205 Posts
|
|
OK! dumb question. How do the pins break? Best
__________________
Mike 2796
SoFo Bunch member
|
01-02-2017, 04:01 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,220
Likes: 483
Liked 11,379 Times in 3,519 Posts
|
|
Extractor alignment pins are .056" x .200", with a very slight crown on the edge at each end. They don't usually break, after some use they literally fall out.....with a little help from the extractor body
__________________
Ret. LE, FA Instr, S&W Armorer
Last edited by armorer951; 01-02-2017 at 04:03 PM.
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
|
|
|
|
All times are GMT -4. The time now is 07:47 AM.