|
|
01-01-2017, 04:54 PM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Northeast TX
Posts: 1,278
Likes: 623
Liked 1,001 Times in 414 Posts
|
|
Swapping Front Sight 586-8
I'm about to change the red ramp front sight to install a patridge sight. I was told by someone he thought the roll pin was made to go in and out only on one side. Is this true?
__________________
Where we go one, we go all
|
01-01-2017, 06:46 PM
|
Suspended
|
|
|
Join Date: Jan 2007
Location: Sandy Utah
Posts: 8,747
Likes: 1,590
Liked 8,911 Times in 3,553 Posts
|
|
Standard practice is pins enter and are removed to/from the right. In actuality it makes no difference as S&W pins are straight, no taper.
|
01-02-2017, 02:35 PM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Northeast TX
Posts: 1,278
Likes: 623
Liked 1,001 Times in 414 Posts
|
|
What diameter punch and bit should this take?
__________________
Where we go one, we go all
|
01-08-2017, 03:00 PM
|
Vendor
|
|
|
Join Date: Jan 2010
Location: Kansas City area
Posts: 6,190
Likes: 54,458
Liked 13,609 Times in 4,289 Posts
|
|
The pins and hole are .055. A .05 punch works well. I use a 1/16 (.062) punch that I put in a cordless drill and ground it down to .05.
|
01-08-2017, 11:30 PM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Northeast TX
Posts: 1,278
Likes: 623
Liked 1,001 Times in 414 Posts
|
|
In fractions, what is a .055? So I can ask for one at the hardware store for a drill bit to drill the hole in the sight blade.
__________________
Where we go one, we go all
|
01-08-2017, 11:39 PM
|
Suspended
|
|
|
Join Date: Jan 2007
Location: Sandy Utah
Posts: 8,747
Likes: 1,590
Liked 8,911 Times in 3,553 Posts
|
|
Nothing in fractions, it is a #54 AWG bit you need. A hardware store is not likely to have wire gauge drill bits.
Last edited by Alk8944; 01-08-2017 at 11:40 PM.
|
The Following User Likes This Post:
|
|
01-09-2017, 09:22 AM
|
|
Moderator
|
|
|
Join Date: Nov 2015
Location: SE Michigan
Posts: 18,596
Likes: 8,408
Liked 17,203 Times in 5,637 Posts
|
|
The closest fraction w/o being too big is 3/64, which is almost .047 of an inch. Don't try to use anything soft, like wire as it will just bend.
__________________
So many S&W's, so few funds!!
|
01-10-2017, 08:01 PM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Northeast TX
Posts: 1,278
Likes: 623
Liked 1,001 Times in 414 Posts
|
|
Thanks guys for the info!
__________________
Where we go one, we go all
|
01-16-2017, 08:10 PM
|
Member
|
|
|
Join Date: Nov 2010
Posts: 532
Likes: 2,772
Liked 709 Times in 235 Posts
|
|
Fellas, would this be the same for my late 90's 640-1? I have tried everything I know but the pin won't budge either way.
Thank you, Dave
|
01-16-2017, 08:54 PM
|
Vendor
|
|
|
Join Date: Jan 2010
Location: Kansas City area
Posts: 6,190
Likes: 54,458
Liked 13,609 Times in 4,289 Posts
|
|
All the sight pins that I've ever seen are the same size. If you have a 1/16 punch, nothing will move because the punch won't fit in the hole.
|
The Following 2 Users Like Post:
|
|
01-16-2017, 09:40 PM
|
Member
|
|
|
Join Date: Nov 2010
Posts: 532
Likes: 2,772
Liked 709 Times in 235 Posts
|
|
Thank you. One side is sticking out just a tad, but the pin won't even budge to get it flush! I've never had one frozen like this. Soaked it for a couple days too, no go. Would heating it with a hair dryer help? Or is just the exact punch the only answer?
|
01-17-2017, 07:47 AM
|
|
Moderator
|
|
|
Join Date: Nov 2015
Location: SE Michigan
Posts: 18,596
Likes: 8,408
Liked 17,203 Times in 5,637 Posts
|
|
Quote:
Originally Posted by Dave Baird
Thank you. One side is sticking out just a tad, but the pin won't even budge to get it flush! I've never had one frozen like this. Soaked it for a couple days too, no go. Would heating it with a hair dryer help? Or is just the exact punch the only answer?
|
I seriously doubt a hair drier would be of any benefit. The proper size and type of punch, along with a proper surface for the revolver is the key. The reason the pin may be protruding from one side may be because the hole is a bit under size and that's as far as the factory could get it in. I'd try removing it from the other side and test the hole size with the proper size drill.
__________________
So many S&W's, so few funds!!
|
The Following User Likes This Post:
|
|
01-17-2017, 09:26 AM
|
Member
|
|
|
Join Date: Nov 2010
Posts: 532
Likes: 2,772
Liked 709 Times in 235 Posts
|
|
Thank you!
|
01-17-2017, 11:40 AM
|
|
Member
|
|
|
Join Date: Dec 2011
Location: S.E. Iowa
Posts: 679
Likes: 288
Liked 731 Times in 309 Posts
|
|
The 629-6 N frame revolvers use the same size roll pin too. I bought a package of 6 #54 bits ( from Amazon) and used one to push out the roll pin. Then another #54 bit to drill the hole in a replacement fiber optic sight.
|
The Following User Likes This Post:
|
|
01-17-2017, 06:35 PM
|
Member
|
|
|
Join Date: Nov 2010
Posts: 532
Likes: 2,772
Liked 709 Times in 235 Posts
|
|
What type of bits are they? None broke while hammering? Got to get me a few of those please!!!
Is this the bit? WESTWARD 2UFN9 Jobber Drill Bit, HSS, Black Oxide, #54 | eBay
Dave
Last edited by Dave Baird; 01-17-2017 at 08:38 PM.
|
01-18-2017, 12:17 PM
|
Vendor
|
|
|
Join Date: Jan 2010
Location: Kansas City area
Posts: 6,190
Likes: 54,458
Liked 13,609 Times in 4,289 Posts
|
|
Yes. Get 3 or 4, not just 1.
|
The Following User Likes This Post:
|
|
01-18-2017, 04:58 PM
|
Member
|
|
|
Join Date: Nov 2010
Posts: 532
Likes: 2,772
Liked 709 Times in 235 Posts
|
|
Will do! Thank you.
|
|
Posting Rules
|
|
|
|
|