|
|
|
01-30-2017, 10:22 AM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Model 60 J frame failure to fire
I recently purchased an older model 60 Smith & Wesson J frame which was pretty dinged up.
Failed to fire about 30% of the time.
Tore the gun down completely meticulously cleaned it replaced the Springs,with Wolf Springs, honed the areas that were recommended to be honed.
Checked the hand, extractor, trigger and Hammer.
The gun now has a trigger pull of approximately 11 - 12 pound.
Still getting failure to fire on about 5 out of 50 rounds it doesn't matter what type or brand of ammunition I am using.
I am getting dimples in the primer from where the firing pin hits it, and on occasion if I cycle it through for the second time it will fire that round. Sometimes not.
Cylinder of seems to rotate properly although it is just a little loose.
I've owned a ton of jframes and never ever had a problem like this.
Any ideas or suggestions on how to remedy this problem would be greatly appreciated.
|
01-30-2017, 10:37 AM
|
Banned
|
|
|
Join Date: Jan 2014
Location: Virginia
Posts: 394
Likes: 542
Liked 449 Times in 171 Posts
|
|
I am no gunsmith, but it sounds like the firing pin is not striking as hard as it should. If you're getting dimples on the primer and a second strike mostly fires, that "could" be the culprit? I am always leery when when the trigger pull has been reduced. Sometimes it takes a harder pull to set off the round.
Remember, the 60 is not a target gun, but rather a self defense firearm.
Just a question.....on a dimpled primer that did not go off on the first pull, how does the dimple compare to primers that did go off on the first pull? Is the indent less? The same? That indent can tell a lot IMHO.
|
01-30-2017, 10:39 AM
|
|
Member
|
|
|
Join Date: Mar 2014
Location: bootheel of Missouri
Posts: 16,891
Likes: 6,992
Liked 28,123 Times in 8,915 Posts
|
|
I'd check to see if somebody knocked a couple loops off the mainspring . . .
__________________
Wisdom comes thru fear . . .
|
The Following 3 Users Like Post:
|
|
01-30-2017, 10:39 AM
|
Member
|
|
|
Join Date: Feb 2013
Posts: 255
Likes: 55
Liked 252 Times in 76 Posts
|
|
Just a guess but I would replace the hammer spring with a new factory one and check the head space, should be .06
|
The Following 2 Users Like Post:
|
|
01-30-2017, 10:43 AM
|
Member
|
|
|
Join Date: May 2004
Location: Buckeye, AZ, USA
Posts: 1,085
Likes: 10,373
Liked 1,324 Times in 487 Posts
|
|
I agree with Muss Muggins and psjoe. Sounds a lot like someone reduced trigger pull by removing coils from the mainspring.
__________________
Dave Frost
|
The Following User Likes This Post:
|
|
01-30-2017, 10:52 AM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,225
Likes: 484
Liked 11,391 Times in 3,522 Posts
|
|
If you have already replaced the springs, including the mainspring, it's likely a headspace problem. The rear gauge should be .060" - .064"....measure with feeler gauges between the rear of the cylinder and the breechface. You don't indicate the dash number of your model 60, but along with measuring for end shake on the cylinder, be sure to check for end shake on the yoke as well. (older models made prior to spring and plunger yoke screw mod)
__________________
Ret. LE, FA Instr, S&W Armorer
|
The Following 3 Users Like Post:
|
|
01-30-2017, 11:43 AM
|
|
US Veteran
|
|
|
Join Date: Aug 2006
Location: West Central IL
Posts: 22,808
Likes: 18,558
Liked 22,429 Times in 8,278 Posts
|
|
Check the firing pin, but usually the guns from this vintage don't have the short pin problem. Did you clean (blow some under pressure cleaner) into the firing pin area?
__________________
H Richard
SWCA1967 SWHF244
|
The Following User Likes This Post:
|
|
01-30-2017, 12:48 PM
|
|
SWCA Member
|
|
|
Join Date: Sep 2006
Location: Henderson,Nevada
Posts: 2,624
Likes: 1,876
Liked 9,107 Times in 1,288 Posts
|
|
Has the hammer been bobbed ? Will have less mass and can lead to misfires.
__________________
SWCA 1932 SWHF 135
|
The Following User Likes This Post:
|
|
01-30-2017, 04:01 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by Zebra War Wagon
I am no gunsmith, but it sounds like the firing pin is not striking as hard as it should. If you're getting dimples on the primer and a second strike mostly fires, that "could" be the culprit? I am always leery when when the trigger pull has been reduced. Sometimes it takes a harder pull to set off the round.
Remember, the 60 is not a target gun, but rather a self defense firearm.
Just a question.....on a dimpled primer that did not go off on the first pull, how does the dimple compare to primers that did go off on the first pull? Is the indent less? The same? That indent can tell a lot IMHO.
|
My error the dimple on the primers that did not go off is much lighter as compared to the dimple on the shots that did fire
Last edited by jhkunkel; 02-03-2017 at 11:06 AM.
Reason: Wording
|
01-30-2017, 04:04 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by Toyman
Has the hammer been bobbed ? Will have less mass and can lead to misfires.
|
Excellent point yes they Hammer has been bobbed but I have had Springs in there that has produced as much is 14 pounds of trigger pull and I still get misfires.
I am thinking of replacing the bobbed Hammer with a regular hammer.
|
The Following User Likes This Post:
|
|
01-30-2017, 04:06 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by armorer951
If you have already replaced the springs, including the mainspring, it's likely a headspace problem. The rear gauge should be .060" - .064"....measure with feeler gauges between the rear of the cylinder and the breechface. You don't indicate the dash number of your model 60, but along with measuring for end shake on the cylinder, be sure to check for end shake on the yoke as well. (older models made prior to spring and plunger yoke screw mod)
|
This is a Model 60 no dash after I measure the headspace if I find there is a problem how do I correct it?
|
01-30-2017, 04:21 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,225
Likes: 484
Liked 11,391 Times in 3,522 Posts
|
|
Shims can be used, if needed, to move the cylinder back. Web site listed below has great service, and high quality products......look under "j-frame shim kit"
TriggerShims Brand Shim Kits
__________________
Ret. LE, FA Instr, S&W Armorer
|
The Following User Likes This Post:
|
|
01-30-2017, 04:37 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by psjoe
Just a guess but I would replace the hammer spring with a new factory one and check the head space, should be .06
|
I have replaced the hammer spring with a wolf hammer spring and when that didn't give me any Improvement I replaced it with a Wilson hammer spring.
The hammer pull is over 12 pounds which I would think would be enough for the firing pin.
I also went so far as to take the hammer spring out of one of my other model 60's which is firing flawlessly put it in this gun still the same results.
The wolf Hammer spring I put in was 14 pounds
Last edited by jhkunkel; 01-30-2017 at 04:40 PM.
|
01-30-2017, 04:45 PM
|
Banned
|
|
|
Join Date: Mar 2014
Location: Battery Oaks Range, S.C.
Posts: 1,847
Likes: 5,663
Liked 3,574 Times in 1,163 Posts
|
|
Sell it to me!!!!!!
|
The Following User Likes This Post:
|
|
01-30-2017, 05:40 PM
|
Member
|
|
|
Join Date: Aug 2001
Location: WV
Posts: 2,438
Likes: 409
Liked 2,849 Times in 1,265 Posts
|
|
Quote:
Originally Posted by jhkunkel
Excellent point yes they Hammer has been bobbed but I have had Springs in there that has produced as much is 14 pounds of trigger pull and I still get misfires.
I am thinking of replacing the bobbed Hammer with a regular hammer.
|
I don't think the hammer being bobbed is the problem. There's far to many S&W's with bobbed hammers that have zero problems. If you've tried new springs, I'd think it's a headspace or firing pin problem as others have suggested.
|
The Following 4 Users Like Post:
|
|
01-30-2017, 09:18 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by Muss Muggins
I'd check to see if somebody knocked a couple loops off the mainspring . . .
|
Put in brand-new Hammer Springs. I tried wolf, Wilson, and Smith & Wesson Originals.
|
01-30-2017, 09:20 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by diyj98
I don't think the hammer being bobbed is the problem. There's far to many S&W's with bobbed hammers that have zero problems. If you've tried new springs, I'd think it's a headspace or firing pin problem as others have suggested.
|
Have not had a chance to measure the headspace yet but I have a feeling that might be the answer to my problem.
One of the contributors gave me the name of a website where I can purchase shims very good information.
|
01-30-2017, 09:23 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by Lee's Landing Billy
Sell it to me!!!!!!
|
This has turned into a real challenge for me and as you can imagine it's very frustrating.
If I can't get it working properly in the next day or two I WILL sell it to you.
|
The Following 2 Users Like Post:
|
|
01-30-2017, 09:26 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by armorer951
Shims can be used, if needed, to move the cylinder back. Web site listed below has great service, and high quality products......look under "j-frame shim kit"
TriggerShims Brand Shim Kits
|
It sounds like this could possibly be the problem, after I measure I will let you know my results, thank you for the information.
|
01-30-2017, 09:47 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,225
Likes: 484
Liked 11,391 Times in 3,522 Posts
|
|
You will be able to "feel" the end shake on the cylinder by moving the closed cylinder front to back. note: a small amount of end shake (.001"-.002") is required for the assembly to function properly.
Check the B/C (barrel cylinder) gap while you're at it. If the rear gauge is out of spec, the front gauge is probably too tight. The front gauge should be .004" - .010".
__________________
Ret. LE, FA Instr, S&W Armorer
|
01-30-2017, 10:10 PM
|
|
Member
|
|
|
Join Date: Dec 2016
Location: Wickiup Junction, OR
Posts: 874
Likes: 11
Liked 1,134 Times in 461 Posts
|
|
I am experiencing the same thing with my new to me M-60 (but while from 1972 mine is essentially 'new') BUT I believe I know why - the previous owner's son replaced the main and trigger rebound spring with about the lightest available. DA trigger pull seems like it is only about 10-11 lbs and SA trigger pull is downright scary! The gun is also very tight as it had most likely never been fired and IS getting better - made it through 50 the other day with only one FTF BUT I am going to replace the springs with standard weight.
|
01-30-2017, 10:45 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by armorer951
You will be able to "feel" the end shake on the cylinder by moving the closed cylinder front to back. note: a small amount of end shake (.001"-.002") is required for the assembly to function properly.
Check the B/C (barrel cylinder) gap while you're at it. If the rear gauge is out of spec, the front gauge is probably too tight. The front gauge should be .004" - .010".
|
What is the difference between headspace and yoke shake?
Do I measure the space between the rear of the cylinder and the frame?
The cylinder does seem to move back and forth more than it does on another of my J frames.
|
01-30-2017, 11:20 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,225
Likes: 484
Liked 11,391 Times in 3,522 Posts
|
|
The "rear gauge" as S&W calls it, is the area between the breechface and the rear of the cylinder. It's measured with the cylinder closed, in the area between the cylinder and the firing pin bushing.
End shake on the yoke is a symptom of an improperly fit or worn interface between the button on the end of the yoke stem, and the yoke screw in the sideplate. If not fit correctly, this causes the entire yoke/cylinder assembly to move forward.....and thereby, opening the rear gauge.
End shake on the cylinder is gauge between the end of the yoke barrel and it's bearing surface inside the cylinder. As these surfaces wear, the cylinder can move forward on the yoke barrel and open the rear gauge to the point where the revolver begins to misfire, due to failure of the end of the hammer nose to adequately reach the primer.
__________________
Ret. LE, FA Instr, S&W Armorer
Last edited by armorer951; 01-31-2017 at 03:10 PM.
|
The Following 6 Users Like Post:
|
|
01-31-2017, 10:13 AM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by armorer951
The "rear gauge" as S&W calls it, is the area between the breechface and the rear of the cylinder. It's measured with the cylinder closed, in the area between the cylinder and the firing pin bushing.
End shake on the yoke is a symptom of an improperly fit or worn interface between the button on the end of the yoke stem, and the yoke screw in the sideplate. If not fit correctly, this causes the yoke/cylinder assembly to move forward.....and thereby, opening the rear gauge.
End shake on the cylinder is gauge between the end of the yoke barrel and it's bearing surface inside the cylinder. As these surfaces wear, the cylinder can move forward on the yoke barrel and open the rear gauge to the point where the revolver begins to misfire, due to failure of the end of the hammer nose to adequately reach the primer.
|
Head space measures at .063
Would that be enough to cause my FTF problem?
If so would a shim solve the problem?
I appreciate all your help on this and I'm also learning a lot.
Thank you
|
01-31-2017, 10:20 AM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by jhkunkel
Head space measures at .063
Would that be enough to cause my FTF problem?
If so would a shim solve the problem?
I appreciate all your help on this and I'm also learning a lot.
Thank you
|
I just noticed that in dry firing my Model 60 that works perfectly the firing pin seems to extend just a little bit more than it does on the model 60 that I'm having problems with. Could that fact also be contributing to my problem?
|
01-31-2017, 03:07 PM
|
Member
|
|
|
Join Date: Jun 2012
Location: Demon-class planet
Posts: 7,403
Likes: 29,169
Liked 8,461 Times in 3,772 Posts
|
|
Poster "armorer951" is a very skilled gunsmith with many years of experience working with S&W revolvers. Were I in your shoes, having a problem with a carry gun like a Model 60, I would take the gun to a similarly trained gunsmith and have it put right professionally with an explanation of the difficulty.
Kaaskop49
Shield #5103
|
The Following 4 Users Like Post:
|
|
01-31-2017, 03:17 PM
|
Banned
|
|
|
Join Date: Mar 2014
Location: Battery Oaks Range, S.C.
Posts: 1,847
Likes: 5,663
Liked 3,574 Times in 1,163 Posts
|
|
Still hovering like a buzzard.
|
The Following 2 Users Like Post:
|
|
01-31-2017, 03:25 PM
|
Member
|
|
|
Join Date: Jan 2008
Location: Wilson, NC
Posts: 1,288
Likes: 464
Liked 823 Times in 375 Posts
|
|
Quote:
Originally Posted by Lee's Landing Billy
Still hovering like a buzzard.
|
Me too. I've never had the specified problem, but I'd like to know what caused it in case I ever do.
|
01-31-2017, 03:30 PM
|
Member
|
|
|
Join Date: Jan 2012
Location: Outside Philadelphia Pa
Posts: 16,601
Likes: 7,342
Liked 17,200 Times in 7,303 Posts
|
|
Quote:
Originally Posted by jhkunkel
I recently purchased an older model 60 Smith & Wesson J frame which was pretty dinged up.
Failed to fire about 30% of the time.
Tore the gun down completely meticulously cleaned it replaced the Springs,with Wolf Springs, honed the areas that were recommended to be honed.
Checked the hand, extractor, trigger and Hammer.
The gun now has a trigger pull of approximately 11 - 12 pound.
Still getting failure to fire on about 5 out of 50 rounds it doesn't matter what type or brand of ammunition I am using.
I am getting dimples in the primer from where the firing pin hits it, and on occasion if I cycle it through for the second time it will fire that round. Sometimes not.
Cylinder of seems to rotate properly although it is just a little loose.
I've owned a ton of jframes and never ever had a problem like this.
Any ideas or suggestions on how to remedy this problem would be greatly appreciated.
|
Had the same problem with a model 27-2. Sold it off
Sent from my XT1650 using Tapatalk
|
The Following User Likes This Post:
|
|
01-31-2017, 03:32 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,225
Likes: 484
Liked 11,391 Times in 3,522 Posts
|
|
Your headspace appears to be within allowable tolerances.
Lack of protrusion could be an issue. Normally, the nose protrudes approx. .040" - .045" beyond the breechface. (a dime is .050") Tolerances allowed among the various parts involved can sometimes cause protrusion to be a bit shorter or longer. Another possibility would be damage to the hammer nose, the hammer nose bushing, dirt/debris or damage in the hammer cavity in the frame.....or debris or dirt behind the extractor. (and there are others)
__________________
Ret. LE, FA Instr, S&W Armorer
|
The Following User Likes This Post:
|
|
01-31-2017, 04:00 PM
|
Member
|
|
|
Join Date: Oct 2007
Location: GA
Posts: 221
Likes: 55
Liked 95 Times in 53 Posts
|
|
I have a 60-14 that I fire several thousand rounds a year through. Up until recently its been 100%. I know at one time I had a wolf kit, a Wilson kit and an apex kit that have gone into different J frames. I think I have stock springs (trying to identify springs is some sort of tricky) but I think I do. I cant seem to find a good illustration of the springs that should be in it including the firing pin spring. That said I have found that out of 100-150 rounds I will get 3-4 failure to fires. I can load them in another gun and they fire like clock work. I am following as well. This is to a point I don't have faith any longer in my once most reliable side kick.
|
The Following User Likes This Post:
|
|
01-31-2017, 05:02 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by armorer951
Your headspace appears to be within allowable tolerances.
Lack of protrusion could be an issue. Normally, the nose protrudes approx. .040" - .045" beyond the breechface. (a dime is .050") Tolerances allowed among the various parts involved can sometimes cause protrusion to be a bit shorter or longer. Another possibility would be damage to the hammer nose, the hammer nose bushing, dirt/debris or damage in the hammer cavity in the frame.....or debris or dirt behind the extractor. (and there are others)
|
I will check the protrusion on the nose.
I have completely disassembled the gun and cleaned it meticulously there's no dirt or anything in any of the cavities or extractor.
I did notice not the cylinder has a bit of side to side wobble for lack of a better term. Is it possible that the cylinder lock up is created a problem?
You certainly are extremely knowledgeable and have been very helpful in my trying to figure this out. I'm not certain if this is the proper venue to ask or not but someone mentioned that perhaps if I sent the gun to you you could check it over, I understand that would be a cost involved but that's not a problem. Assuming the cost would be a little less than a million dollars.
It's more about figuring out what the problem is there anything else.
|
01-31-2017, 05:05 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
You mentioned that the headspace seems to be within tolerance, so can I assume ordering and putting a shim in would be a waste of time?
|
01-31-2017, 05:08 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by camsdaddy
I have a 60-14 that I fire several thousand rounds a year through. Up until recently its been 100%. I know at one time I had a wolf kit, a Wilson kit and an apex kit that have gone into different J frames. I think I have stock springs (trying to identify springs is some sort of tricky) but I think I do. I cant seem to find a good illustration of the springs that should be in it including the firing pin spring. That said I have found that out of 100-150 rounds I will get 3-4 failure to fires. I can load them in another gun and they fire like clock work. I am following as well. This is to a point I don't have faith any longer in my once most reliable side kick.
|
I understand what you're saying that is my feeling exactly.
There would be no point in my carrying this gun if it is not one hundred percent reliable.
|
01-31-2017, 05:13 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by jhkunkel
I understand what you're saying that is my feeling exactly.
There would be no point in my carrying this gun if it is not one hundred percent reliable.
|
This is an older model 60 with no dash so the firing pin is riveted to the hammer. It is my understanding that you can no longer replace just the firing pin on this type of hammer and Smith & Wesson no longer makes them.
The search to isolate the problem continues.
|
01-31-2017, 06:13 PM
|
|
Member
|
|
|
Join Date: May 2016
Posts: 227
Likes: 190
Liked 291 Times in 119 Posts
|
|
It sounds like there was both yoke and endshake issues. Solve the yoke first. 1. Take out yoke screw, remove yoke, take hammer and wack the sumvabic at 2 o'clock. Slide back in put in, close, reinstall screw and see if yoke is tight fore and aft. If not wack that sumvabic harder and try again. Once that is done measure at the forcing cone to cylinder. If over .001 order the shim needed to bring it back to .001. If that doesn't work get a real big hammer and really wack that sumvabic and throw it in a lake.
Last edited by Sol-Invictus; 01-31-2017 at 06:15 PM.
|
The Following User Likes This Post:
|
|
01-31-2017, 06:39 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by Sol-Invictus
It sounds like there was both yoke and endshake issues. Solve the yoke first. 1. Take out yoke screw, remove yoke, take hammer and wack the sumvabic at 2 o'clock. Slide back in put in, close, reinstall screw and see if yoke is tight fore and aft. If not wack that sumvabic harder and try again. Once that is done measure at the forcing cone to cylinder. If over .001 order the shim needed to bring it back to .001. If that doesn't work get a real big hammer and really wack that sumvabic and throw it in a lake.
|
I have a pond nearby, so i may do that:mad as my last attempt!!!
|
01-31-2017, 06:54 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,225
Likes: 484
Liked 11,391 Times in 3,522 Posts
|
|
Any reliability issues in single action?
Some side to side play in the cylinder is normal and necessary. I'm assuming your primer hits are in the center of the primer pocket, more or less.
What about end shake on the yoke, did you check for that? The two crowned sideplate screws can get switched and this can cause problems. The front sideplate screw is fit to the button on the yoke stem.
__________________
Ret. LE, FA Instr, S&W Armorer
Last edited by armorer951; 01-31-2017 at 07:09 PM.
|
01-31-2017, 07:42 PM
|
SWCA Member
|
|
|
Join Date: Apr 2007
Location: Pennsylvania
Posts: 6,634
Likes: 638
Liked 6,872 Times in 2,546 Posts
|
|
I have a 60
Just like yours. They don't make them like
That anymore. Stop wondering and send it to S&W. whatever you sell
It for will be what they charge you to fix it right.
|
The Following User Likes This Post:
|
|
01-31-2017, 08:10 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by armorer951
Any reliability issues in single action?
Some side to side play in the cylinder is normal and necessary. I'm assuming your primer hits are in the center of the primer pocket, more or less.
What about end shake on the yoke, did you check for that? The two crowned sideplate screws can get switched and this can cause problems. The front sideplate screw is fit to the button on the yoke stem.
|
Since it has the bobbed hammer, I can only shoot it in single action if I carefully pull the hammer back. i have done that on several occasions just to check, and it fires every time.
I ordered and have already replaced all the sideplate screws including the yoke. Very little yoke shake. (Hopefully I checked it correctly)
The primer hits are pretty much centered.
I'll probably put it all back together and take it out to the range to see if I can identify any specific oddities.
Any interest in looking at it?
|
01-31-2017, 08:12 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by kbm6893
I have a 60
Just like yours. They don't make them like
That anymore. Stop wondering and send it to S&W. whatever you sell
It for will be what they charge you to fix it right.
|
It's just one of those things that's driving me crazy, and want to understand the big question....WHY???
|
01-31-2017, 09:29 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,225
Likes: 484
Liked 11,391 Times in 3,522 Posts
|
|
Very hard to diagnose problems like this without having the gun in hand. Someone said it's like doing surgery over the phone.
Perhaps you have a trusted, experienced gunsmith in your area? If not, I would suggest contacting S&W Customer Service....either by e-mail or by phone. email: [email protected] TX: 1-800-331-0852.
I'd be happy to look at it for you, but the government frowns on sending firearms through the mail.
__________________
Ret. LE, FA Instr, S&W Armorer
|
The Following 3 Users Like Post:
|
|
01-31-2017, 09:42 PM
|
SWCA Member
|
|
|
Join Date: Apr 2007
Location: Pennsylvania
Posts: 6,634
Likes: 638
Liked 6,872 Times in 2,546 Posts
|
|
Quote:
Originally Posted by jhkunkel
It's just one of those things that's driving me crazy, and want to understand the big question....WHY???
|
They'll tell you when they fix it. Will probably fix things you didn't even know needed fixing. My friend sent his father in law's old model 10 in for a reblue. They fixed the timing and the yoke that he didn't even know were off.
|
The Following User Likes This Post:
|
|
02-01-2017, 11:39 AM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by armorer951
Very hard to diagnose problems like this without having the gun in hand. Someone said it's like doing surgery over the phone.
Perhaps you have a trusted, experienced gunsmith in your area? If not, I would suggest contacting S&W Customer Service....either by e-mail or by phone. email: [email protected] TX: 1-800-331-0852.
I'd be happy to look at it for you, but the government frowns on sending firearms through the mail.
|
Well I just want to say how much I appreciate your help. I have certainly learned a lot.I may take it to a local gunsmith here in Warrenton.
I wouldn't want to get either of us in trouble with the government.
Once again.
THANK YOU
|
02-01-2017, 12:01 PM
|
Member
|
|
|
Join Date: Dec 2016
Location: Gulf Coast
Posts: 93
Likes: 100
Liked 141 Times in 35 Posts
|
|
Shimming S&W for endshake.
|
02-01-2017, 12:27 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,225
Likes: 484
Liked 11,391 Times in 3,522 Posts
|
|
My pleasure. If you have a question, you are welcome to send me a PM.
__________________
Ret. LE, FA Instr, S&W Armorer
|
The Following User Likes This Post:
|
|
02-01-2017, 04:10 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by armorer951
My pleasure. If you have a question, you are welcome to send me a PM.
|
Thank You,
Jim
|
02-01-2017, 07:23 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Quote:
Originally Posted by armorer951
Your headspace appears to be within allowable tolerances.
Lack of protrusion could be an issue. Normally, the nose protrudes approx. .040" - .045" beyond the breechface. (a dime is .050") Tolerances allowed among the various parts involved can sometimes cause protrusion to be a bit shorter or longer. Another possibility would be damage to the hammer nose, the hammer nose bushing, dirt/debris or damage in the hammer cavity in the frame.....or debris or dirt behind the extractor. (and there are others)
|
I just thought I would point out that the nose protrusion seems less than the .040 - .045 you cited. The nose does not appear to be damaged when compared with my other J frame hammers.
I have completely resembled the gun and we'll take it up to the range again in a day or two. I'll report back in detail what problems if any I encountered.
|
02-02-2017, 05:52 PM
|
Member
|
|
|
Join Date: Dec 2015
Location: Virginia
Posts: 86
Likes: 49
Liked 14 Times in 11 Posts
|
|
Took 2 Smith & Wesson J frames M-60 to the range today.
My good old standby performed flawlessly, not a FTF in 100 rounds.
My problem Model 60 had 3 FTF's out of 50.
You could clearly see that the primer hits were very light when compared to the ones that fired.
Does this help in any way on determining what the problem might be?
|
02-02-2017, 06:08 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,225
Likes: 484
Liked 11,391 Times in 3,522 Posts
|
|
Not really.
If both of the guns are older models that have a hammer mounted hammer nose (firing pin) you could try swapping the hammers in the guns. If the hammers are compatible, and the hammer from the more "reliable" model restores reliability 100% of the time, then you've pretty much narrowed the problem down to the hammer.
Other than a defective hammer nose there are a couple of other possibilities, including something called "hammer hits rebound". Not a likely cause, but possible. Also, just to double check, put empty casings in the gun and check the rear gauge again...make sure the casings are fully seated in the chambers before a measurement is taken.
Any idea if the misfires are occurring in the same chamber each time?
__________________
Ret. LE, FA Instr, S&W Armorer
Last edited by armorer951; 02-03-2017 at 11:07 AM.
|
The Following User Likes This Post:
|
|
|
|
Posting Rules
|
|
|
|
|