Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > S&W-Smithing
o

Notices

S&W-Smithing Maintenance, Repair, and Enhancement of Smith & Wesson and Other Firearms.


Reply
 
Thread Tools Display Modes
  #1  
Old 03-25-2018, 04:08 PM
dr. mordo's Avatar
dr. mordo dr. mordo is offline
Member
1903 Hand Ejector crane problem? 1903 Hand Ejector crane problem? 1903 Hand Ejector crane problem? 1903 Hand Ejector crane problem? 1903 Hand Ejector crane problem?  
Join Date: Jul 2017
Location: Miami, FL
Posts: 1,677
Likes: 5,138
Liked 2,954 Times in 1,021 Posts
Default 1903 Hand Ejector crane problem?

My mom has had this gun for 25 years, and I recently took it to give it some TLC (which it desperately needs!).

It seems to shoot fine, but I noticed the front lock is not engaging. Any thoughts on what is causing this? It looks to me like the crane is a tiny bit bent.

Also, any idea what the finish is? It looks almost like paint to me (though mineral spirits had no effect on it) and seems to be wearing thru on the other side because I can see some nickle shining thru. Obviously, the gun is not worth much at all, but I'm pretty handy and figured I'd mess around with it a bit. The previous owner bobbed the hammer and 'painted' it, both of which I'd like to undo.

1903 Hand Ejector crane problem?-1903-he-1-jpg
Attached Images
File Type: jpg 1903 HE 1.jpg (73.9 KB, 99 views)
Reply With Quote
The Following User Likes This Post:
  #2  
Old 03-26-2018, 09:22 AM
glowe's Avatar
glowe glowe is offline
US Veteran

1903 Hand Ejector crane problem? 1903 Hand Ejector crane problem? 1903 Hand Ejector crane problem? 1903 Hand Ejector crane problem? 1903 Hand Ejector crane problem?  
Join Date: Nov 2009
Location: Michigan Western UP
Posts: 12,912
Likes: 3,028
Liked 14,245 Times in 5,432 Posts
Default

That is a pre-1928 cut barrel 32 Hand Ejector. First thing to determine is if the pin is working properly. It is spring loaded, so just pushing it from the rear and letting it go will determine if it is binding. Oil it if it is working properly and try the next step.

The next thing to look for is a bent ejector rod. Does the pin "seat" into the knob when you rotate the cylinder? If so, open the cylinder looking from the front and watch the knob as you rotate the cylinder. If it wobbles, the rod is probably a little bent. It would simply need to be straightened, but remember that that ejector rod is hollow and very thin.

If the rod runs true, the yoke (crane) is bent. You first have to determine what direction it needs to be straightened by looking closely at the location of the pin in relationship to the hole in the knob. If the knob is left or right of the pin, that is the direction the yoke is bent. Up or down means the yoke is very slightly "racked".

Depending on your skill level at disassembling the ejector rod and cylinder, and performing some slight bending of the yoke, the job is can be done at home with some care and repeated assembly/disassembly. One needs to do this while the yoke is still on the revolver. After removing the cylinder and ejector rod, take a long rod about the diameter of the ejector rod hole and, after securing your revolver frame in a vise, you can apply pressure to the yoke. This will re-align the hole with the pin. Do this in very small steps until your pin drops into the ejector hole.

If you are not comfortable doing this kind of work, it should be off to the gunsmith or look for a replacement crane for your revolver. Numrich has them, but they are not cheap. ebay is another place to look for early I frame yokes. Keep in mind that you have a $150 gun, so the yoke at Numrich is half the value, but if the sentimental value is higher, by all means get it fixed.
__________________
Gary
SWCA 2515
Reply With Quote
The Following User Likes This Post:
  #3  
Old 03-26-2018, 01:19 PM
WR Moore WR Moore is offline
Member
 
Join Date: Oct 2006
Posts: 6,579
Likes: 1,787
Liked 5,342 Times in 2,685 Posts
Default

I don't see any light between the locking bolt lug and the end of the ejector/extractor rod. Is the rod screwed in all the way? Should be right hand threads. Do make sure the locking bolt goes back and forth freely. There should be visible clearance between the end of the rod and the lug.

The best way to check the yoke is with a pin gauge. If the bend isn't too bad, it can be straightened in the frame. Brass hammer/babbit bar is the general method, but I'd check the ejector/extractor rod for straightness first. There is supposed to be an internal tapered cone in the end of the ejector/extractor.

Last edited by WR Moore; 03-26-2018 at 01:20 PM.
Reply With Quote
The Following User Likes This Post:
  #4  
Old 03-26-2018, 06:57 PM
dr. mordo's Avatar
dr. mordo dr. mordo is offline
Member
1903 Hand Ejector crane problem? 1903 Hand Ejector crane problem? 1903 Hand Ejector crane problem? 1903 Hand Ejector crane problem? 1903 Hand Ejector crane problem?  
Join Date: Jul 2017
Location: Miami, FL
Posts: 1,677
Likes: 5,138
Liked 2,954 Times in 1,021 Posts
Default

Thanks very much for the help! I'll take a closer look and let you know how it goes.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Found 1903 First Change Hand Ejector 32 hand Plain Old Dave WANTED to Buy 1 01-04-2017 04:47 PM
my first 1903 hand ejector good454cu S&W Hand Ejectors: 1896 to 1961 7 02-23-2013 09:40 AM
1903 hand ejector .32 - value increase? Mobilman44 S&W Hand Ejectors: 1896 to 1961 4 10-02-2012 10:19 PM
32 hand ejector model of 1903 sugarae S&W Hand Ejectors: 1896 to 1961 7 12-26-2009 02:23 PM
What is it...1903, hand ejector? n2hunting S&W Hand Ejectors: 1896 to 1961 3 06-30-2009 06:51 AM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 07:01 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)