|
|
03-24-2017, 02:39 PM
|
Member
|
|
|
Join Date: Dec 2016
Posts: 97
Likes: 0
Liked 70 Times in 42 Posts
|
|
What weight Wolff rebound spring?
A while back I reported my M19 snub had locked up due to the ejector rod backing out. Got that sorted out.
That resulted in one of the ratchet pins coming out. I found the pin and reinstalled it successfully.
Now I want to replace the rebound spring. I have the Wolff spring kit. Which weight should I go with?
I'll be using the gun in club level IDPA matches.
|
03-24-2017, 02:55 PM
|
|
Moderator
|
|
|
Join Date: Nov 2015
Location: SE Michigan
Posts: 18,476
Likes: 8,386
Liked 17,059 Times in 5,594 Posts
|
|
The rebound spring isn't nearly as critical as the hammer spring. You should be able to go with their lightest w/o any problems. Too light on the hammer spring though can cause primer failure, unless you switch to reloads with Federal primers.
__________________
So many S&W's, so few funds!!
|
The Following 2 Users Like Post:
|
|
03-24-2017, 03:19 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,205
Likes: 481
Liked 11,335 Times in 3,505 Posts
|
|
If they check your SA pull befor the matches, the lighter rebound springs may cause the gun to fail this integrity check. Light springs will have an affect on the SA pull weight.....making it lighter. A very light rebound spring may also cause reliability issues in terms of trigger return. If you are doing any rapid firing during the match, you'll need to retain enough force in the rebound spring to insure positive trigger return.
Without any further internal modification, you should be able to use a 13 to 14 pound rebound spring in your model 19. Make sure to check your SA pull rate after any spring modifications/substitututions.....and test fire the gun with your match ammo to ensure reliability. The minimum SA factory pull is 3 pounds.
__________________
Ret. LE, FA Instr, S&W Armorer
Last edited by armorer951; 03-24-2017 at 03:24 PM.
|
The Following 3 Users Like Post:
|
|
03-24-2017, 03:21 PM
|
Member
|
|
|
Join Date: Aug 2007
Location: Oklahoma
Posts: 8,158
Likes: 3,605
Liked 5,199 Times in 2,172 Posts
|
|
I use 14# on my IDPA revolver so I get a snappy return with no dragging. I use the strutted mainspring with an extended strain set to 7# double action pull.
Some go lighter on both, and I beat some people who get some misfires in a match.
__________________
Science plus Art
|
The Following User Likes This Post:
|
|
03-25-2017, 03:36 AM
|
|
Member
|
|
|
Join Date: Dec 2012
Location: N.E. OKLA.
Posts: 6,461
Likes: 5,859
Liked 9,272 Times in 3,480 Posts
|
|
I vote for the 14# rebound spring too.
I just added one to my M357 Night Guard that had a 4-3/4# SA pull before. After polishing the rebound block, lube & 14# spring it was right at 2-3/4#, which was better than I usually get.
Sometimes I have to clip 1/2 a turn or more to get the 2-1/2# SA I like for my casual target shooting.
.
__________________
Waiting for the break of day
|
03-25-2017, 12:54 PM
|
|
US Veteran
|
|
|
Join Date: Aug 2006
Location: West Central IL
Posts: 22,758
Likes: 18,437
Liked 22,313 Times in 8,245 Posts
|
|
I always use the 14# spring for reliability.
__________________
H Richard
SWCA1967 SWHF244
|
03-25-2017, 09:31 PM
|
Member
|
|
|
Join Date: Dec 2016
Posts: 97
Likes: 0
Liked 70 Times in 42 Posts
|
|
I installed a 14 lb spring and shot it last night in IDPA pratice. After firing a cylinder load to check "0", I shot the stages, going for only head shots! Not that much of a challenge as the furthest targets were at 12 yards.
I think it is going to be a fun gun.
|
03-25-2017, 10:03 PM
|
Member
|
|
|
Join Date: Mar 2003
Location: New England, USA
Posts: 4,468
Likes: 3,068
Liked 4,294 Times in 1,610 Posts
|
|
Good Choice.
I've found the 14# will drop in and work well and reliably in just about any S&W revolver. 13 or 12# if you are willing to do some extensive polishing of the internals.
I don't normally change out the hammer/main spring unless I'm going for a super light DA trigger in a range (only) gun.
__________________
Dave
Last edited by Wee Hooker; 03-25-2017 at 10:04 PM.
|
03-26-2017, 06:16 AM
|
Member
|
|
|
Join Date: Jan 2013
Location: Florida
Posts: 1,555
Likes: 312
Liked 1,741 Times in 746 Posts
|
|
14# does seem to be the sweet spot. I've sometimes been able to go lighter with polishing, but usually I end up not getting as positive trigger reset as I like with the 12/13# springs.
|
The Following User Likes This Post:
|
|
03-26-2017, 10:34 AM
|
|
Member
|
|
|
Join Date: Jul 2016
Location: Santa Cruz Mountains, CA
Posts: 309
Likes: 596
Liked 369 Times in 157 Posts
|
|
I use a 13# rebound in my 617. Lightened up SA pull nicely.
I have a 12# that I was going to try but it is just fine with the 13# and I have read of reset issues using with a too light a rebound spring so I am sticking with the 13#.
|
03-26-2017, 11:34 AM
|
Member
|
|
|
Join Date: Dec 2016
Posts: 97
Likes: 0
Liked 70 Times in 42 Posts
|
|
Comparing the lengths of the various Wolff springs, you, can't judge their rating by that. Thank God they package them separately.
I have a couple of loose rebound springs of unknown rating. Is there way of determining what rating they are?
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
|
|
|
|