Smith & Wesson Forum

Go Back   Smith & Wesson Forum > >


Reply
 
Thread Tools Display Modes
  #1  
Old 06-19-2017, 08:02 AM
jimmyj's Avatar
jimmyj jimmyj is online now
Member
Cerakote Finish Cerakote Finish Cerakote Finish Cerakote Finish Cerakote Finish  
Join Date: May 2003
Location: DUNNELLON, FLORIDA USA
Posts: 7,826
Likes: 831
Liked 6,849 Times in 2,148 Posts
Smile Cerakote Finish

Has anyone applied "Cerakote" to a firearm?
Is this a "Do It Your Self" spray on finish ?

Thanks,
Jimmy
Reply With Quote
  #2  
Old 06-19-2017, 09:30 AM
chief38's Avatar
chief38 chief38 is offline
Member
Cerakote Finish  
Join Date: Apr 2006
Posts: 8,969
Likes: 1,698
Liked 6,096 Times in 2,833 Posts
Default

Yes - it's a DIY product. I've not sprayed any of my guns (I don't really care for the look) but some of my shootin' Bud's have and if you like that sort of look it comes out pretty good. So far the durability has been OK, but it's only been a year or so since they did it - therefore I can no tell you the long term quality.

There are several other products on the market that are all basically the same as the Cerakote. Another one is called Dura-coat and I don't recall the other names. If you google them you can find names, prices, reports on ease of use and durability. Just follow directions to the T.
Reply With Quote
  #3  
Old 06-19-2017, 12:34 PM
Tyrod Tyrod is online now
Member
Cerakote Finish Cerakote Finish Cerakote Finish Cerakote Finish Cerakote Finish  
Join Date: Oct 2011
Location: Sunny Central Florida
Posts: 1,048
Likes: 281
Liked 704 Times in 263 Posts
Default

I think Cerakote is a cut above most of the other "spray-on" finishes. It has very specific prep requirements. The others aren't too picky about prep. Then Ceracoat H has a bake cure cycle. Most of the others don't. Then there's the ceramic component. I don't know if that is really important or marketing hype. If you have the capability for air brushing and an oven that can get to the requisite temp then try it. I do know Ceracoat is far more durable than Dura-coat which is known for fast wear out. I've seen Ceracoat finishes that have been chipped but I haven't seen any that have had wear.
__________________
NRA Benefactor
Reply With Quote
  #4  
Old 06-19-2017, 12:44 PM
BAM-BAM BAM-BAM is online now
Member
 
Join Date: Oct 2005
Location: Western Pa.
Posts: 7,071
Likes: 153
Liked 7,722 Times in 3,704 Posts
Default

I have had 2 3rd Gen frames done by a local Gunsmith ..... a 6904 and a 915..... both have seen "moderate use" over about 2 to 2 1/2 years with no wear noted. Both guns were purchased used and had moderate wear and "ring rash" on the frames..... but the slides were closer to 95%......

They have been carried more than shot.......(when I want a gun but don't want to take one of my "better/more expensive" guns).......since the refinish.

IIRC cost was about ....... $75 for each frame...... both are now reverse two tone....... mat "silver" frames w/ blue slides.
While TTSH would disapprove ....... they look good IMHO and I'd rather carry them than a Glock for a beater/ ATV /truck gun!!!!

Last edited by BAM-BAM; 06-19-2017 at 12:50 PM.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Cerakote TonySoprano9VE Smith & Wesson SD & Sigma Pistols 4 11-15-2016 02:14 PM
Cerakote M&P 9c motorcyclejoe Smith & Wesson M&P Pistols 12 01-28-2016 06:54 PM
CeraKote MNBassn Smith & Wesson Semi-Auto Pistols 2 10-13-2014 04:22 PM
Cerakote hmbiohazard Smith & Wesson SD & Sigma Pistols 8 03-01-2014 02:12 PM
Cerakote vs. Birdsong's Black T finish jfd Smith & Wesson Semi-Auto Pistols 12 02-10-2011 07:30 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 10:24 AM.


S-W Forum, LLC 2000-2015
Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)