|
|
09-04-2017, 10:34 AM
|
|
Member
|
|
|
Join Date: Jul 2010
Location: Fort Collins CO
Posts: 381
Likes: 160
Liked 442 Times in 122 Posts
|
|
Can this be polished out of stainless
So a couple of years ago, I acquired one of my favorite carry guns, a 3" 686 CS-1. I Love it, carry it always camping and hiking, action is great and accurate. The problem is Bubba got to it before me, and tried his hand at engraving.....so functionally it is fine, and I'm fine with it if can't be fixed, but it's a CS-1 and would be so much cooler restored. I knew what it was when I purchased it and got it cheap, but if you think this could be corrected I may attempt or send it off to be polished. I know the sideplate could be replaced and fitted with a new one to take care of that side, but what about the other?
|
The Following User Likes This Post:
|
|
09-04-2017, 10:45 AM
|
|
Member
|
|
|
Join Date: Mar 2014
Location: bootheel of Missouri
Posts: 16,888
Likes: 6,990
Liked 28,119 Times in 8,912 Posts
|
|
That is unfortunate. I'm no expert, but from a hillbilly point of view, it looks like that's there to stay . . .
__________________
Wisdom comes thru fear . . .
|
09-04-2017, 10:52 AM
|
SWCA Member
|
|
|
Join Date: Aug 2015
Location: Central Ohio
Posts: 2,507
Likes: 18,594
Liked 4,675 Times in 1,719 Posts
|
|
Have to agree - with the above post. Probably there to stay. An expert will be along to give you any options that exist. That is a pistol I am looking for. Not necessarily the cs1, but short barrel 686.
|
09-04-2017, 10:53 AM
|
|
US Veteran
|
|
|
Join Date: Jan 2010
Location: The wet side of Oregon
Posts: 6,292
Likes: 8,813
Liked 7,785 Times in 2,377 Posts
|
|
Hard to see how deep those gouges go.
I have smoothed out some pretty deep ones.
Issue is, you're not just polishing that spot, but the entire area.
__________________
-jwk-
US Army '72-'95
|
09-04-2017, 10:59 AM
|
Member
|
|
|
Join Date: Feb 2006
Posts: 3,422
Likes: 1,105
Liked 5,144 Times in 1,578 Posts
|
|
I'd live with it as a nice shooter and look for better example if you want one.
Last edited by sodacan; 09-04-2017 at 11:08 AM.
|
The Following User Likes This Post:
|
|
09-04-2017, 11:14 AM
|
|
Member
|
|
|
Join Date: Apr 2006
Posts: 17,799
Likes: 7,843
Liked 25,701 Times in 8,685 Posts
|
|
The engraved side doesn't look too too bad but it's unclear from the picture exactly what happened to the side plate. The gun can be sanded down but it's also difficult to tell how deep the engraving and milky etching of the Side Plate actually go from pic's. You could contact Fords or give it a whirl yourself if you are daring. The main problem I see is if you start sanding you will loose the S&W Logo as well. You might just want to address the Side Plate side and call it a day. Keep it as a "shooter".
Last edited by chief38; 09-04-2017 at 11:16 AM.
|
The Following 2 Users Like Post:
|
|
09-04-2017, 12:57 PM
|
US Veteran
|
|
|
Join Date: Oct 2011
Location: Southern Virginia
Posts: 1,961
Likes: 9,647
Liked 2,427 Times in 1,028 Posts
|
|
The left side is way less of a "Bubba" mess than many I have seen.
I likely would just accept the scrolls as "personalizing" my gun.
The right side is another story. Neither my memory nor imagination can render a cause for that cloudy look ?
Certainly at the least I would try a little gentle buffing with Flitz polish, with the duel attitude of;... it's mine, and;...what can it hurt to try now.
Replacement side plate fitting is iffy at best, more especially on revolvers that are somewhat limited in production numbers, as opposed to those like a model 10.
At the least you have a gun you want, that shoots well for you.
__________________
wanna do right-- not right now
|
The Following User Likes This Post:
|
|
09-04-2017, 01:12 PM
|
|
Member
|
|
|
Join Date: Jul 2010
Location: Fort Collins CO
Posts: 381
Likes: 160
Liked 442 Times in 122 Posts
|
|
thanks for the opinions, it will probably stay as is, maybe I will try some polish on the side plate to see I f I can make it look better, I can't make it worse. I think the side plate is a result of already trying to erase some engraving done on it so they left the other side. it is a fairly rare 686, being one of the one Smith and Wesson made for US. customs and it has the 2M stamp indicati ng it was probably actually in service
|
The Following User Likes This Post:
|
|
09-04-2017, 01:35 PM
|
Member
|
|
|
Join Date: Jan 2006
Location: Loganville, Ga.
Posts: 354
Likes: 171
Liked 133 Times in 75 Posts
|
|
I can't tell how deep the engraving is, but if it were mine, I would use sanding blocks and 600 grit paper. Bead blasting would be my next step. Dean
|
The Following 2 Users Like Post:
|
|
09-04-2017, 01:40 PM
|
|
US Veteran
|
|
|
Join Date: Apr 2003
Location: Texas, USA
Posts: 1,113
Likes: 1,826
Liked 1,170 Times in 310 Posts
|
|
Have it engraved. A good engraver could incorporate what is already done into a custom job, I'm sure. Kind of like a cover up tattoo,,,
|
The Following 8 Users Like Post:
|
|
09-04-2017, 01:46 PM
|
SWCA Member
|
|
|
Join Date: Jul 2013
Posts: 1,095
Likes: 2,858
Liked 5,194 Times in 722 Posts
|
|
I like Celtics idea. Just like a coverup tattoo, have a well known engraver go at it! Can't botch it any worse than it already is.
SVT28
|
09-04-2017, 02:44 PM
|
|
Moderator
|
|
|
Join Date: Jun 2007
Posts: 26,870
Likes: 976
Liked 18,987 Times in 9,290 Posts
|
|
I would contact the factory Performance Center and see what they might be able to do. I'm sure they have removed pitting deeper than the engraving from metal, and they can top it off with a bead blast finish that would most closely resemble the original factory appearance. The wild card is the sideplate and they may have to examine the gun to determine if it can be used.
__________________
Alan
SWCA LM 2023, SWHF 220
|
09-04-2017, 03:19 PM
|
|
Member
|
|
|
Join Date: Apr 2011
Location: Where this month?
Posts: 3,604
Likes: 264
Liked 4,215 Times in 1,714 Posts
|
|
Side plate is easy.. remove and use a flat plate with 1000 grit then go to 2000 grit sand paper and rem oil. use alternating direction with each stroke about 60 degree changes. You'll get a nearly polished look if done right with the last stroke simulating the original grain direction, then polish the plate and gun to match.
|
The Following 3 Users Like Post:
|
|
09-04-2017, 03:34 PM
|
|
Member
|
|
|
Join Date: Jun 2004
Location: Independence, OH, USA
Posts: 6,944
Likes: 28,935
Liked 7,229 Times in 2,599 Posts
|
|
Send it out to a good engraver and see if he can add a little more to it and make the bubba stuff look better. Larry
|
09-05-2017, 01:03 AM
|
|
Member
|
|
|
Join Date: Oct 2003
Location: Southeast Wisconsin
Posts: 1,750
Likes: 7
Liked 657 Times in 369 Posts
|
|
That sideplate doesn't appear to fit very well. It almost looks as though somebody installed a sideplate from a nickle 581 or 586 and the nickle has turned chalky. I'd have Smith replace it with a correct piece and live with the rest. Most anything can be fixed IF you throw enough money at the problem. Do you really want to pursue that?
Bruce
|
09-05-2017, 02:06 PM
|
|
Member
|
|
|
Join Date: Jul 2014
Location: Mojave Desert
Posts: 10,352
Likes: 18,044
Liked 24,224 Times in 6,853 Posts
|
|
I'd beadblast it and call it good. It's never going to be factory perfect; it's a quality carry gun and shooter.
|
The Following User Likes This Post:
|
|
09-05-2017, 05:15 PM
|
Member
|
|
|
Join Date: Oct 2006
Location: Frisco, TEXAS
Posts: 225
Likes: 1
Liked 77 Times in 31 Posts
|
|
sideplate
that sure looks like completely different side plate.
you could also have it Cerakoted
|
09-05-2017, 06:55 PM
|
Member
|
|
|
Join Date: Apr 2014
Location: New Hampshire
Posts: 407
Likes: 156
Liked 570 Times in 158 Posts
|
|
I was going to say also...that plate looks nickel. If it is, I'd have a new stainless one fitted. The engraving on the other side, it doesn't look too bad actually. I bet it can be removed, and then blend polish the entire gun. You'll likely lose the logo, but I believe Smith will etch a new one on there. If you're not trying to get it back to factory look, you could even remove the engraving and have the whole gun color case hardened...I know, it's kind of out there but really does look awesome and Tyler gun works does stainless steel. I normally wouldn't suggest such a thing but the gun may not ever look factory fresh so you might as well go crazy and make it yours. Lots that can be done with that gun...it's all just money lol.
|
The Following User Likes This Post:
|
|
09-05-2017, 07:10 PM
|
|
SWCA Member
|
|
|
Join Date: Feb 2005
Location: Cocoa Beach, Florida
Posts: 10,579
Likes: 3,066
Liked 22,559 Times in 5,844 Posts
|
|
Quote:
Originally Posted by CelticSire
Have it engraved. A good engraver could incorporate what is already done into a custom job, I'm sure. Kind of like a cover up tattoo,,,
|
I have to agree.
A engraving job can turn a sows ear into a silk purse.
You end up with a nice BBQ gun and a story about how you rescued it from obscurity
|
The Following 2 Users Like Post:
|
|
09-06-2017, 11:05 PM
|
|
Member
|
|
|
Join Date: Oct 2003
Location: Southeast Wisconsin
Posts: 1,750
Likes: 7
Liked 657 Times in 369 Posts
|
|
I have to agree.
Quote:
A engraving job can turn a sows ear into a silk purse.
You end up with a nice BBQ gun and a story about how you rescued it from obscurity
|
Like I said, if you throw enough money at it, you can fix most anything.
Bruce
Last edited by BruceM; 09-06-2017 at 11:06 PM.
|
The Following User Likes This Post:
|
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
|
|
|
|