|
|
01-28-2020, 02:49 AM
|
|
Member
|
|
|
Join Date: Mar 2012
Location: Upstate, SC
Posts: 2,029
Likes: 3,122
Liked 4,807 Times in 1,538 Posts
|
|
Barrel Indexing Problem
Hi,
I just picked up this nice 1950 Target, and noticed that the rear sight needed to be adjusted far left to get it zeroed. (see pic #1)
Later, I noticed that the reason for this is that the barrel is indexed past the 12 O'Clock position. (see pic #2) The barrel rib can be clearly seen as not being aligned with the topstrap. To go along with this, the front sight is slightly canted off center. Also the ejector doesn't quite fit with the locking stud in the barrel shroud.
So, what's the fix? Can the barrel be backed off slightly (given that the work would be done by a competent person having the right tools), or does the barrel need to be completely reset?
Kuhnhausen and a couple others suggest the latter.
I suppose if it's the latter case, it's the whole ball of wax: resetting the shoulder, possibly cutting one more turn of thread, facing off the barrel breech, and recutting the forcing cone.....?
Thanks for any advice,
Jim
PS: See post #14 for update
Last edited by 6string; 02-01-2020 at 05:58 AM.
Reason: title correction, update
|
The Following 3 Users Like Post:
|
|
01-28-2020, 05:26 AM
|
|
Member
|
|
|
Join Date: Jan 2012
Location: OVER the hill in TEJAS
Posts: 2,725
Likes: 13,107
Liked 4,339 Times in 1,773 Posts
|
|
I am not a smith but the gun has a pin in the barrel. I would have someone with the proper tools move it a little maybe without removing the pin and test. That is much more than a thread index. The surface looks good. I would like to see the rest of the gun. Does it target bench shoot good with the sight adjusted? It looks like a one owner from the top.
Last edited by 4barrel; 01-28-2020 at 05:35 AM.
|
The Following User Likes This Post:
|
|
01-28-2020, 05:47 AM
|
|
Member
|
|
|
Join Date: Mar 2012
Location: Upstate, SC
Posts: 2,029
Likes: 3,122
Liked 4,807 Times in 1,538 Posts
|
|
Hi,
Thanks for the reply. I've attached a few more pics.
Yes, it's a pinned barrel. And, the pin looks totally unmolested. So, I doubt it has ever been removed for any reason.
I count 10 grooves in the barrel rib and top strap. It looks like the misalignment is about the distance value of one or two grooves?
There's no sign anywhere that this revolver has been worked on inappropriately; all screws slots are clean, no tool marks or scratches.
Serial # S 85xxx so, about 1952. Could it have been shipped this way?
It is my understanding that the torque on the pinned barrels was a bit less than the later unpinned barrels. (IE: fitted so it hand tightens to 1/8th turn less than 12 o'clock, then use a barrel wrench/fixture for the final 1/8th turn.) So, I wonder if backing the barrel out slightly would still be within an acceptable amount of torque?
Jim
PS: It shot right, even with the rear sight blade adjusted that far left. So, I really believe given the height of the front sight (Patridge) the getting the barrel aligned properly will fix things.
Last edited by 6string; 01-28-2020 at 06:37 AM.
Reason: added PS
|
The Following 2 Users Like Post:
|
|
01-28-2020, 07:27 AM
|
|
Member
|
|
|
Join Date: Feb 2011
Location: Central PA
Posts: 4,557
Likes: 8,216
Liked 11,453 Times in 3,023 Posts
|
|
I have never had to "tweek" the barrel on a pinned S&W, so I cant say how that would effect things.
I have done so to several fixed sighted SA revolvers with excellent results. Both required at least as much of a turn as yours appears to need to get things hitting POA. The cylinder gap change was minimal, having no negative effect.
I am not a gunsmith, but I believe the small amount of correction your barrel needs should not be enough to have to worry about the barrel shooting loose. I would try it, and worse case situation, the barrel starts to loosen upon use, or the retaining pin wont properly fit, and you have to go thru the effort of having the barrel shoulder turned down, and the barrel re-fit.
Nice looking 1950 Target, by the way.
Larry
|
The Following 2 Users Like Post:
|
|
01-28-2020, 08:14 AM
|
Member
|
|
|
Join Date: May 2010
Location: The Steel City
Posts: 2,158
Likes: 6,840
Liked 4,405 Times in 1,409 Posts
|
|
Have an experienced smith turn the barrel back into place. If he feels it's not a tight enough fit he can Loctite the barrel in place. Andy did that for me on a Triple Lock in lieu of setting the barrel back a turn.
|
The Following 3 Users Like Post:
|
|
01-28-2020, 08:15 AM
|
|
Member
|
|
|
Join Date: Apr 2005
Location: Birdsboro Pa.
Posts: 444
Likes: 183
Liked 199 Times in 92 Posts
|
|
A few years back I bought a 25-2 that looked beautiful, but after I got it home I noticed the barrel was over tightened. I took it to the local S&W guru and he moved it back. He said sometimes they don't go back all the way, but mine came out nice.
The Handgunner Shop.. Topton Pa.
Randy has changed barrels for me, and recently "tightened" a barrel on a 929. Those rear sights were the opposite of yours, and are now centered.
|
The Following User Likes This Post:
|
|
01-28-2020, 08:33 AM
|
Member
|
|
|
Join Date: Mar 2012
Posts: 5,831
Likes: 3,902
Liked 5,902 Times in 2,543 Posts
|
|
If the pic of the rear sight indicates how far left you had to set it to achieve desired zero, and the gun shoots and functions correctly and to your liking, I wouldn't change a thing; that rear blade isn't very far left at all...
Otherwise, is a qualified revolversmith near you to have a look and make a suggestion? It seems a gentle "touch" a few degrees over in the proper equipment might correct, but you're right, if the barrel has to be pulled I'd guess the full treatment will be required.
The latter might be worth it if, say, you already have excessive barrel-cylinder gap, but otherwise I'd suggest avoiding "the works" and living with the slight cant if everything else is in order.
Again, I've seen the rear sight blade torqued a lot farther over to get zero on otherwise good revolvers.
__________________
Pickpocket
|
The Following 2 Users Like Post:
|
|
01-28-2020, 08:47 AM
|
|
US Veteran
|
|
|
Join Date: Oct 2013
Location: Central Montana
Posts: 13,719
Likes: 12,860
Liked 39,491 Times in 10,051 Posts
|
|
I believe with proper tools the barrel could be turned back without removing the pin. The groove in the barrel shank is actually a bit generous and will allow several degrees of movement without anything bending. If it returns to the slightly canted position there is anothe fix before setting the barrel back. Remove barrel and use a small punch to make say 8 spaced small punch marks around the shoulder that mates to the frame. This will displace a small amount of metal around each punch and that metal will contact the frame earlier than the shoulder did before and increase the torque required to align it. I doubt it will ever move again. Did it to my 18-4 years ago. It is still straight after thousands of rounds.
Barrel cylinder gap. One complete turn is .027777----. There are 360 degrees in a turn so each degree only gives you .000077. so 3 or 4 degrees won't change much. It takes 13 degrees to get .001
Last edited by steelslaver; 01-28-2020 at 08:59 AM.
|
The Following 12 Users Like Post:
|
4barrel, 6string, chief38, Hapworth, Hondo44, jack the toad, JH1951, Muley Gil, Nomadmax, Protocall_Design, reccpd101, stansdds |
01-28-2020, 05:28 PM
|
SWCA Member
|
|
|
Join Date: Oct 2007
Location: California
Posts: 19,251
Likes: 11,933
Liked 20,598 Times in 8,583 Posts
|
|
What steelslaver posted has always worked for me. I followed the methods in old gun smithing manuals. It's usually not required to dimple with a punch, but if so, I dimple the mating surface on the frame, not the barrel shoulder.
The barrel will not return to being canted to the left. If the barrel is not tight enough after straightening it, when shooting the gun the barrel tends to turn to the right due to the rifling twist. If that happens, then resort to dimple the frame mating surface to the barrel. But I doubt it will be necessary.
__________________
Jim
S&WCA #819
|
The Following 2 Users Like Post:
|
|
01-29-2020, 07:03 AM
|
|
Member
|
|
|
Join Date: Mar 2012
Location: Upstate, SC
Posts: 2,029
Likes: 3,122
Liked 4,807 Times in 1,538 Posts
|
|
To All Who Responded,
I am very grateful for your informed responses, and the time you took to answer. There is a lot of knowledge on this great forum.
A number of you guys have consistently, over the years, provided fantastic insights and experiences that has always been appreciated.
The seller, also a forum member, has been extremely helpful and generous.
This is a very nice revolver and deserves to be properly adjusted.
So, I plan to see if just tweaking the fit by backing out the barrel a degree or two solves the problem. My hope all along was that might just work. If it works, great. If not, then there's other options.
I'll follow up with the details, and more pictures.
Thanks again, and I'll be sure to revisit this thread...
Jim
|
The Following 4 Users Like Post:
|
|
01-29-2020, 10:12 AM
|
|
Member
|
|
|
Join Date: Apr 2006
Posts: 17,829
Likes: 7,854
Liked 25,754 Times in 8,706 Posts
|
|
I agree with Steelslaver - a Smith with experience might be able to move the barrel just a smidgeon without removing the pin. Sometmes the pin and the flat on the barrel have some play and will allow it to move a little. Yours is not off all that much.
|
The Following 3 Users Like Post:
|
|
01-29-2020, 11:18 AM
|
Member
|
|
|
Join Date: Oct 2006
Posts: 6,658
Likes: 1,825
Liked 5,415 Times in 2,732 Posts
|
|
Having fitted quite a few barrels I've got a slightly different take than some posters.
Real briefly, the best way to evaluate the issue is to pull the barrel pin and loosen the barrel about 90 degrees. Turn the barrel in hand tight. If the (from the rear) left hand side of the barrel rib lines up with the right hand side of the frame rib, you can just turn the barrel in to proper alignment and you'll have correct torque.
If the barrel comes up short, if it's very slightly slightly short pull it and lightly apply some grease to the barrel shoulder. Be very careful in moving it to index point. Anything significant, you'll need to lightly face the barrel shoulder.This is a skill of the craft thing evaluating what you can muscle without cracking the frame.
If the barrel turns past that alignment point with hand pressure, you'll pretty much have to do the barrel set back. Kinda depends on how far past. That doesn't involve cutting any new threads, just moving the shoulder-don't forget to trim any under lug if the ejector rod is enclosed.
Last edited by WR Moore; 01-29-2020 at 11:25 AM.
|
The Following 2 Users Like Post:
|
|
01-29-2020, 05:54 PM
|
Member
|
|
|
Join Date: May 2011
Location: USA
Posts: 280
Likes: 5
Liked 249 Times in 116 Posts
|
|
I did the punch dimples on a 25-2 that was indexed too far. It worked out fine. Quite often, if you have to loosen the barrel to get the correct index, even a little, it will be loose, and you will need to either do the punch marks to raise some metal, before retightening, or locktite the threads. I have heard of some putting a thin shim up against the barrel shoulder, to get the same effect. Recutting the shoulder would be a last resort.
|
The Following User Likes This Post:
|
|
02-01-2020, 05:56 AM
|
|
Member
|
|
|
Join Date: Mar 2012
Location: Upstate, SC
Posts: 2,029
Likes: 3,122
Liked 4,807 Times in 1,538 Posts
|
|
Problem seems to be fixed
Hi,
Well, I decided to just do the work myself. Fitting a set of oak blocks for the frame and barrel was straightforward. I used a pin block vise I made for working on grand piano pin blocks as a bench-mounted barrel vise. I used a large Jorgensen #2 handscrew as the wrench. After set-up, the adjustment was fairly easy, just took a number of raps on the handscrew with a wooden mallet. It was very controllable. It moved very minutely bit by bit.
(As a related experience, before having a bad accident a few years ago, I did a lot of cycling and bike work. I often worked on vintage Italian bikes, with removal and adjustment of the headset or bottom bracket being common. The issues involved seem similar to barrel indexing.)
I took it to the range yesterday and put 100 rds through it to see if it was OK. All cast bullet loads from 200 gr target loads to stiff 250 gr loads. Before and after pics confirm it was unchanged.
At the same time, I did some accuracy work at 25 and 50 yds. Got one very lucky 5 shot group at 50 yds (with the stiff 250 gr RNFP load). No question, it's a great shooter!
There's a few pictures here to show some of the highlights.
Mostly, I want to thank everyone for their great help.
Sincerely,
Jim
|
The Following 12 Users Like Post:
|
4barrel, bgrafsr, Hondo44, Jebus35745, Kurusu, Muley Gil, P.44, Protocall_Design, R*E, reccpd101, series guy, Warren Sear |
02-01-2020, 08:28 AM
|
|
US Veteran
|
|
|
Join Date: Oct 2013
Location: Central Montana
Posts: 13,719
Likes: 12,860
Liked 39,491 Times in 10,051 Posts
|
|
Looks great and shoots great. It is a fine revolver. I would just keep an eye on it and you know plenty of options if it ever does move. There is a certain satisfaction in knowing you managed something like this
Enjoy
|
The Following 3 Users Like Post:
|
|
02-01-2020, 11:04 AM
|
US Veteran SWCA Member Absent Comrade
|
|
|
Join Date: Nov 2009
Location: upstate SC / Mtns SW Va
Posts: 4,789
Likes: 3,064
Liked 9,875 Times in 1,986 Posts
|
|
I AM IMPRESSED. AND YES I AM SHOUTING.
__________________
Charlie
|
The Following 2 Users Like Post:
|
|
02-01-2020, 05:12 PM
|
Member
|
|
|
Join Date: Aug 2018
Location: West Texas
Posts: 309
Likes: 96
Liked 204 Times in 130 Posts
|
|
Rather than rely on punch marks which may or may not be the same height, I peen the mating shoulder on the barrel for the full 360 degrees with a small, polished face hammer. (See the previous thread about planishing). Several trips around the barrel shoulder will push up enough metal, evenly, to allow the proper torque when reassembling. Using light taps with a smooth hammer, the job can be done with no marks showing. By the way, I lay the barrel on a piece of lead while topping on to prevent any damage to the under side.
|
The Following User Likes This Post:
|
|
02-01-2020, 06:13 PM
|
SWCA Member
|
|
|
Join Date: Oct 2007
Location: California
Posts: 19,251
Likes: 11,933
Liked 20,598 Times in 8,583 Posts
|
|
Quote:
Originally Posted by Kp321
Rather than rely on punch marks which may or may not be the same height, I peen the mating shoulder on the barrel for the full 360 degrees with a small, polished face hammer. (See the previous thread about planishing). Several trips around the barrel shoulder will push up enough metal, evenly, to allow the proper torque when reassembling. Using light taps with a smooth hammer, the job can be done with no marks showing. By the way, I lay the barrel on a piece of lead while topping on to prevent any damage to the under side.
|
Can you post a photo of a barrel that you've peened/fitted that way?
__________________
Jim
S&WCA #819
|
02-01-2020, 06:30 PM
|
Member
|
|
|
Join Date: May 2011
Location: USA
Posts: 280
Likes: 5
Liked 249 Times in 116 Posts
|
|
Peening does work also. It does give a little more metal contact to but up against the frame. Hopefully in the OP's case he may only need a few thousandths, and a few moderate taps around the shoulder may get what he needs without leaving peen marks.
|
The Following User Likes This Post:
|
|
02-02-2020, 10:42 AM
|
|
US Veteran
|
|
|
Join Date: Oct 2013
Location: Central Montana
Posts: 13,719
Likes: 12,860
Liked 39,491 Times in 10,051 Posts
|
|
Quote:
Originally Posted by Kp321
Rather than rely on punch marks which may or may not be the same height, I peen the mating shoulder on the barrel for the full 360 degrees with a small, polished face hammer. (See the previous thread about planishing). Several trips around the barrel shoulder will push up enough metal, evenly, to allow the proper torque when reassembling. Using light taps with a smooth hammer, the job can be done with no marks showing. By the way, I lay the barrel on a piece of lead while topping on to prevent any damage to the under side.
|
Usually more than one good way to skin a cat. Never thought of that. Hard to do anything about right at the rib or an ejector shroud on barrels with those, But a little on each side of those should be sufficient. It is all about moving the metal in the direction you desire. I don't think that the "crater" areas around the punch marks need to be completely uniform. Only trying to create enough for it to tighten up. Some of the metal around the crater mouth will be flattened by the turning motion as barrel tightens evening everything out. But for just a few degrees either method works well. Like Hondo doing his metal movement on the frame and me doing it on barrel. Easier to get straight uniform punches on the frame shoulder. I just try to stay away from messing with the frame if I can. But, I confess if a barrel doesn't go all the way into time it is easier to remove a tiny bit from the frame face than barrel shoulder. 1 degree needs just .000077 of metal. 5 degrees .000385. A couple of smooth flat passes with a good file will get you a few degrees and everything stays flat and square.
I read your thread on planishing and have to agree. Itt works. Best done before any sanding or filing. You want the mental in the high spots for moving into the low ones.
Most people never stop to really think about something like a dent. Yes there is a low spot, but the metal didn't disappear, it got moved. It is sometimes possible to move it back.
Last edited by steelslaver; 02-02-2020 at 10:58 AM.
|
The Following 3 Users Like Post:
|
|
02-03-2020, 10:20 AM
|
|
Member
|
|
|
Join Date: Jun 2004
Location: Independence, OH, USA
Posts: 6,950
Likes: 28,984
Liked 7,242 Times in 2,604 Posts
|
|
Hey Jim, glad it worked out. Was watching to see what the conclusion would be. Larry
|
The Following User Likes This Post:
|
|
|
Posting Rules
|
|
|
|
|