|
|
09-29-2020, 06:57 PM
|
Member
|
|
|
Join Date: Feb 2010
Location: Wyoming
Posts: 6,175
Likes: 6,402
Liked 7,086 Times in 3,003 Posts
|
|
Need some help replacing a bbl
I happen to have a M-19 that was setup to be a target gun with a heavy bbl. It was done up really nice but I have no use for such a Frankenstein. When I got it I got the box papers original 4 inch bbl stocks sights etc. Though I have worked on S&W internals have never removed a bbl. Bbl is pinned. Just wondering if the pin is tapered? does it have to come out left to right or vice versa? Or doesn't it matter?
|
09-29-2020, 07:35 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,225
Likes: 484
Liked 11,390 Times in 3,522 Posts
|
|
The barrel pin is not tapered. It can be removed/replaced in either direction.
__________________
Ret. LE, FA Instr, S&W Armorer
|
The Following 2 Users Like Post:
|
|
09-29-2020, 07:53 PM
|
Vendor
|
|
|
Join Date: Jan 2010
Location: Kansas City area
Posts: 6,190
Likes: 54,459
Liked 13,612 Times in 4,290 Posts
|
|
Make sure you take the crane (yoke) out before trying to unscrew the barrel. Otherwise, you will damage it.
|
The Following User Likes This Post:
|
|
09-29-2020, 10:47 PM
|
Member
|
|
|
Join Date: Dec 2016
Location: South Carolina
Posts: 1,713
Likes: 1,054
Liked 3,520 Times in 961 Posts
|
|
I'd suggest you take it to a gunsmith unless you have the correct tools. Trying to remove a barrel without proper knowledge and tools can easily lead to a warped frame. Ask me how I know
|
The Following User Likes This Post:
|
|
09-29-2020, 11:41 PM
|
SWCA Member
|
|
|
Join Date: Oct 2007
Location: California
Posts: 19,251
Likes: 11,929
Liked 20,598 Times in 8,583 Posts
|
|
Pins, including on Smith & Wessons, usually go in from the right and out from the left. But by looking at the frame around the pin hole you can usually determine the direction because there will be a slight ring or burr of metal that's pushed out when the pin was originally installed. If you drive the pin in from the left, you'll sometimes create the burr around the right side of the hole as well.
As posted above, the pins are straight.
That would be an easy barrel to replace because you have the original which was fit to that frame so the front sight is straight up and down when it's tightened. Unless you want to learn how to change barrels, I too would take it to a gunsmith. But again it will be easy (less expensive) because the barrel is already fitted and will not likely need any work on a lathe.
If you want to do it just ask and I'll send the procedure. But you will need a frame 'wrench' either purchased or home made.
__________________
Jim
S&WCA #819
|
The Following 2 Users Like Post:
|
|
09-30-2020, 12:34 AM
|
Member
|
|
|
Join Date: Mar 2013
Posts: 633
Likes: 509
Liked 581 Times in 321 Posts
|
|
Heck just send it to Frank Glenn.
Penny wise,pound foolish.
|
09-30-2020, 02:39 AM
|
Member
|
|
|
Join Date: Feb 2010
Location: Wyoming
Posts: 6,175
Likes: 6,402
Liked 7,086 Times in 3,003 Posts
|
|
I was pretty certain it was straight. Just checking to make sure. I am confident I can do the job. If I have any trouble...I have a friend who is one of the best handgun smiths over round Cody....but he dies mostly Single Actions. I'm more concerned with getting the bbl back on straight. I have replaced bbls on rifles...and a few Colt revolvers
|
The Following User Likes This Post:
|
|
09-30-2020, 09:49 AM
|
SWCA Member
|
|
|
Join Date: Oct 2007
Location: California
Posts: 19,251
Likes: 11,929
Liked 20,598 Times in 8,583 Posts
|
|
Skeet 028,
Well then you'll likely have fun doing it and not problems. I like working on my own guns, it's an additional satisfaction to acquiring, owning, and shooting them for me.
Enjoy,
__________________
Jim
S&WCA #819
|
The Following User Likes This Post:
|
|
|
Posting Rules
|
|
|
|
|