|
|
11-08-2020, 03:13 PM
|
SWCA Member
|
|
|
Join Date: Oct 2020
Location: Central Texas
Posts: 167
Likes: 668
Liked 394 Times in 98 Posts
|
|
Sideplate burrs
Sometimes when a sideplate has been pried off or otherwise handled roughly, some small raised edges appear on the upper sideplate seam near the trigger. Does anybody have a suggestion regarding how to "roll" that edge back flush?
|
11-08-2020, 03:45 PM
|
|
Moderator
|
|
|
Join Date: Jan 2007
Location: Great Lakes State
Posts: 29,952
Likes: 12,834
Liked 34,126 Times in 8,020 Posts
|
|
I’d try tapping it down with a small brass hammer. Go slow...
__________________
"I also cook."
|
The Following User Likes This Post:
|
|
11-08-2020, 05:34 PM
|
SWCA Member
|
|
|
Join Date: Oct 2007
Location: California
Posts: 19,250
Likes: 11,925
Liked 20,598 Times in 8,583 Posts
|
|
Don't tap on the front surface!
Usually, pried up side plate seam edges are "upset'. Meaning the metal is bulged up at the seams. Fixing them generally involves flattening the upset bulges w/o removing metal, by pressing the high spots with a flat polished piece of harder metal called a "dolly". I use a polished small chisel bottom surface or other similar machined tool surface as a "dolly".
Lay the sideplate face down on the "dolly": perfectly clean, smooth, hard, and flat surface and tap on the BACK SIDE of the side plate. But don't use the hammer surface. Use a punch with flat, polished tip and tap on the punch with the hammer.
The side plate can be squeezed against the dolly in a vice. Or the dolly can be laid flat on the side plate and tapped on the backside of the "upset" side plate edges to flatten the front side as described above.
A LOT LESS work than fitting an oddball replacement side plate, and at no cost and with better final fit results.
__________________
Jim
S&WCA #819
|
The Following 10 Users Like Post:
|
|
11-09-2020, 02:45 PM
|
SWCA Member
|
|
|
Join Date: Oct 2020
Location: Central Texas
Posts: 167
Likes: 668
Liked 394 Times in 98 Posts
|
|
Thanks for the information; will be helpful.
|
11-10-2020, 07:40 AM
|
|
US Veteran
|
|
|
Join Date: Nov 2013
Location: South Central Texas
Posts: 1,185
Likes: 2,688
Liked 1,114 Times in 501 Posts
|
|
Quote:
Originally Posted by s&wchad
I’d try tapping it down with a small brass hammer. Go slow...
|
I also have peened my cylinder notches in this manner. VERY LIGHTLY, and checked by running my fingernail over the notch edge after every tap. NOTE: If you over do it, you will need to see/have a local smithy correct your timing, so be very aware...
Last edited by HorizontalMike; 11-10-2020 at 07:42 AM.
|
11-10-2020, 08:53 AM
|
|
Member
|
|
|
Join Date: Oct 2020
Location: Switzerland
Posts: 308
Likes: 1,705
Liked 530 Times in 189 Posts
|
|
Thank you Jim, have just encountered this problem for the first time a couple of weeks ago and was wondering about how to go about it. Easy to make it worse.
|
The Following User Likes This Post:
|
|
11-10-2020, 10:34 PM
|
|
Member
|
|
|
Join Date: May 2020
Location: Southern Indiana
Posts: 20
Likes: 38
Liked 10 Times in 7 Posts
|
|
Ok, this is probably a stupid question, but would it be possible to flatten the sideplate seam without taking the sideplate off? Could maybe something like a highly polished socket from your socket set be used to tap and sort of roll the seam back down? Of course you would tap on the socket while holding it to the seam, not actually tap the gun with the socket.
|
11-11-2020, 02:53 AM
|
SWCA Member
|
|
|
Join Date: Oct 2007
Location: California
Posts: 19,250
Likes: 11,925
Liked 20,598 Times in 8,583 Posts
|
|
No stupid questions.
Anything other than a flat polished surface used against the top surface will not usually be satisfactory.
The socket will likely leave a ripple affect on the upset burr. And one hammer tap a little askew will probably leave a tiny divot in the side plate from the other end of the socket.
__________________
Jim
S&WCA #819
|
The Following 2 Users Like Post:
|
|
11-11-2020, 08:28 AM
|
|
US Veteran
|
|
|
Join Date: Oct 2013
Location: Central Montana
Posts: 13,715
Likes: 12,858
Liked 39,476 Times in 10,046 Posts
|
|
Everyone that does much mechanical work needs a fair sizes SMOOTH flat hard surface. I have several anvils, some 1/4 brass plate and a granite inspection plate about 18"x18" and several brass hammers. I bought a smaller nylon and rubber hammer with the screw on faces. Took off the rubber one and made one from some aluminum round stock. Some brass and aluminum round stock of various sizes is also very handy to have around.
Just like the side plate spot lots of times metal is actually just displaced and not gone. Stamping, cylinder notches, dings etc. You may not always be able to move it all back, but a good share of it will go back and help.
I have removed the import markings from 2 of the 4 J&G gun smith special K frames so far and after some tapping it doesn't take much sanding to get the metal smooth again. Yes, that is legal, wrote the BATF for clarification. Law only prohibits removal of original serial number.
|
|
Posting Rules
|
|
|
|
|