Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > S&W-Smithing
o

Notices

S&W-Smithing Maintenance, Repair, and Enhancement of Smith & Wesson and Other Firearms.


Reply
 
Thread Tools Display Modes
  #1  
Old 01-03-2021, 03:06 PM
Jerry in SC Jerry in SC is offline
Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Apr 2007
Location: Upstate
Posts: 465
Likes: 150
Liked 93 Times in 55 Posts
Default 1946 K-22 misfires

My son recently picked up a decent K-22 of approximately 1946 or 47 vintage, lots of holster wear but mechanically good, with the exception of a tiny bit of cylinder end shake. I didn't get a chance to check it out before he bought it.

It's having an occasional misfire with multiple ammo types and brands (even the match stuff). The mainspring looks to be original as does the screw. I've tried to tighten the mainspring screw but it appears to be down tight. The firing pin is protruding well enough seems a little loose in the bushing.

I'm hesitant to use Power end shake washers so am asking for advice as to the best method to correct.
Reply With Quote
  #2  
Old 01-03-2021, 03:30 PM
bigmoose's Avatar
bigmoose bigmoose is offline
Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Apr 2010
Location: Central New York State
Posts: 1,616
Likes: 3,459
Liked 2,104 Times in 629 Posts
Default

You may need to remove the sideplate and thoroughly clean and lube it. How does the area where the hammer and pin fall into appear? Is there built up crud there? Is the cylinder timing correctly as it rotates?
Heavy dried up grease at hammer pivot may slow the hammer fall enough to cause light strikes.

Last edited by bigmoose; 01-03-2021 at 03:32 PM.
Reply With Quote
The Following User Likes This Post:
  #3  
Old 01-03-2021, 03:54 PM
mmande's Avatar
mmande mmande is online now
SWCA Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Sep 2007
Location: Iowa
Posts: 1,385
Likes: 378
Liked 519 Times in 280 Posts
Default

One of the first things we teach new shooters in our clubs revolver league is to make sure the ammo is pressed tightly into the chamber. Weather rim fire or center fire there can be build up in the chamber and the round will not seat properly. When the firing pin first hits the round it merely seats it into the chamber because there isn't enough resistance to set the primer off. If it still doesn't go off on the second hit then you need to look into other causes of the misfire.
Just a thought;
Mike
__________________
Mike
S&WCA #2470
Reply With Quote
The Following User Likes This Post:
  #4  
Old 01-03-2021, 03:58 PM
hogblue hogblue is offline
Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Dec 2009
Location: S.W. Missouri
Posts: 351
Likes: 124
Liked 587 Times in 156 Posts
Default

The masterpiece I received from my uncle and was doing the same thing you described. A trip to the plant cured the problem. Excellent customer service. It’s as good as new
Reply With Quote
  #5  
Old 01-03-2021, 04:01 PM
OutWest50 OutWest50 is offline
SWCA Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Oct 2020
Location: Central Texas
Posts: 156
Likes: 616
Liked 376 Times in 91 Posts
Default

All of the suggestions that bigmoose provides make sense and should be checked. Excessive endshake can result in misfires. The best remedy for endshake is either to stretch the yoke tube (gunsmith) or install proper thickness cylinder shim bearings; either of which provides the same end result. I have used the shim bearings on several occasions and they work very well. One thing to note is to also check for yoke endplay with the cylinder removed and yoke in place. Correct yoke end play first with yoke bearing, then address cylinder endshake with cylinder bearing.
Reply With Quote
  #6  
Old 01-03-2021, 04:50 PM
jag22 jag22 is offline
Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Dec 2010
Location: Dallas
Posts: 701
Likes: 3
Liked 356 Times in 212 Posts
Default

I would for sure start out with a thorough cleaning, especially with a gun that old where you don’t know it’s history. That would include removing the strain screw and cleaning its pocket as well as the screw itself. Cleaning may not solve the problem but that’s where you need to start. I also check YouTube for any helpful videos.
Reply With Quote
The Following User Likes This Post:
  #7  
Old 01-03-2021, 05:05 PM
Geno44 Geno44 is offline
Member
1946 K-22 misfires  
Join Date: Oct 2008
Location: S/W Illinois
Posts: 923
Likes: 554
Liked 1,152 Times in 445 Posts
Default

How do the firing pin marks on all the cases look? Are they uniform and "normal"?
Reply With Quote
The Following 2 Users Like Post:
  #8  
Old 01-03-2021, 06:49 PM
Jerry in SC Jerry in SC is offline
Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Apr 2007
Location: Upstate
Posts: 465
Likes: 150
Liked 93 Times in 55 Posts
Default

Quote:
Originally Posted by Geno44 View Post
How do the firing pin marks on all the cases look? Are they uniform and "normal"?
They look consistent.
Reply With Quote
  #9  
Old 01-03-2021, 06:52 PM
steelslaver's Avatar
steelslaver steelslaver is online now
US Veteran
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Oct 2013
Location: Central Montana
Posts: 13,625
Likes: 12,742
Liked 39,091 Times in 9,966 Posts
Default

The endshake shims work very well and I prefer them to stretching the yoke. The shims are hardened steel and provide a perfectly smooth hard surface for the cylinder to run on. .If that and a good cleaning doesn't cure it possibly a new tension screw. Some people (me) shorten the screw. But, I never leave one close to the edge of fire or misfire.
Reply With Quote
  #10  
Old 01-03-2021, 06:52 PM
Jerry in SC Jerry in SC is offline
Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Apr 2007
Location: Upstate
Posts: 465
Likes: 150
Liked 93 Times in 55 Posts
Default

Quote:
Originally Posted by mmande View Post
One of the first things we teach new shooters in our clubs revolver league is to make sure the ammo is pressed tightly into the chamber. Weather rim fire or center fire there can be build up in the chamber and the round will not seat properly. When the firing pin first hits the round it merely seats it into the chamber because there isn't enough resistance to set the primer off. If it still doesn't go off on the second hit then you need to look into other causes of the misfire.
Just a thought;
Mike
Yes we always check the seating. The chambers are nice and clean with no build up at the leade to keep them from seating properly.
Reply With Quote
  #11  
Old 01-03-2021, 06:55 PM
Jerry in SC Jerry in SC is offline
Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Apr 2007
Location: Upstate
Posts: 465
Likes: 150
Liked 93 Times in 55 Posts
Default

Quote:
Originally Posted by bigmoose View Post
You may need to remove the sideplate and thoroughly clean and lube it. How does the area where the hammer and pin fall into appear? Is there built up crud there? Is the cylinder timing correctly as it rotates?
Heavy dried up grease at hammer pivot may slow the hammer fall enough to cause light strikes.
I’ve removed the side plate and cleaned all the parts, the firing pin area looks nice and clean. Timing is perfect, the hammer fall feels a bit light.
Reply With Quote
  #12  
Old 01-03-2021, 07:06 PM
Jerry in SC Jerry in SC is offline
Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Apr 2007
Location: Upstate
Posts: 465
Likes: 150
Liked 93 Times in 55 Posts
Default

Quote:
Originally Posted by OutWest50 View Post
All of the suggestions that bigmoose provides make sense and should be checked. Excessive endshake can result in misfires. The best remedy for endshake is either to stretch the yoke tube (gunsmith) or install proper thickness cylinder shim bearings; either of which provides the same end result. I have used the shim bearings on several occasions and they work very well. One thing to note is to also check for yoke endplay with the cylinder removed and yoke in place. Correct yoke end play first with yoke bearing, then address cylinder endshake with cylinder bearing.
My suspicion is cylinder endshake being the cause, there is no yoke end play (one of the first things I check on a older S&W). I’ll try the Power shims.

Last edited by Jerry in SC; 01-03-2021 at 07:10 PM.
Reply With Quote
  #13  
Old 01-03-2021, 07:10 PM
Jerry in SC Jerry in SC is offline
Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Apr 2007
Location: Upstate
Posts: 465
Likes: 150
Liked 93 Times in 55 Posts
Default

Quote:
Originally Posted by steelslaver View Post
The endshake shims work very well and I prefer them to stretching the yoke. The shims are hardened steel and provide a perfectly smooth hard surface for the cylinder to run on. .If that and a good cleaning doesn't cure it possibly a new tension screw. Some people (me) shorten the screw. But, I never leave one close to the edge of fire or misfire.
There is a possibility of a shortened screw, but finding a correct one is not easy for a pre number 5 screw. I have the yoke stretching tool but don’t want to use it on a K-22 this old. The shims will be my first avenue.
Reply With Quote
  #14  
Old 01-03-2021, 07:10 PM
murphydog's Avatar
murphydog murphydog is offline
Moderator
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Jun 2007
Posts: 26,782
Likes: 936
Liked 18,876 Times in 9,241 Posts
Default

If the hammer strike force is unusually light, the mainspring strain screw may have been shortened. Buying a new one for comparison, or putting a spent primer on the old one and re-trying it at the range may help.
__________________
Alan
SWCA LM 2023, SWHF 220
Reply With Quote
The Following 5 Users Like Post:
  #15  
Old 01-03-2021, 09:27 PM
ruger 22 ruger 22 is offline
Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Jan 2012
Location: NY
Posts: 802
Likes: 1,634
Liked 1,081 Times in 483 Posts
Default

Geno44 hit on a problem I had with my 34-1. I had misfires on all kinds of different ammo but the marks were consistent. I have since shot 2 bricks of Federal with not a single misfire. It was the ammo.
Reply With Quote
  #16  
Old 01-03-2021, 09:43 PM
dwh's Avatar
dwh dwh is offline
SWCA Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Dec 2014
Location: SW PA
Posts: 496
Likes: 622
Liked 1,578 Times in 352 Posts
Default

My M17 had a similar problem with misfires. It had a broken firing pin. I quick and easy repair.
__________________
Dave
Regulators mount up!
Reply With Quote
  #17  
Old 01-03-2021, 10:13 PM
dsf dsf is offline
Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Jan 2006
Location: Escaping CA to OR in 2024
Posts: 1,166
Likes: 1,141
Liked 1,424 Times in 577 Posts
Default

Quote:
Originally Posted by Jerry in SC View Post
I’ve removed the side plate and cleaned all the parts, the firing pin area looks nice and clean. Timing is perfect, the hammer fall feels a bit light.
Re post #14, an expended small primer with anvil removed gives just a bit more "oomph" to the hammer fall. I know it's a Rube Goldberg solution, but it works. Absent a new mainspring or strain screw.

There are other ways to accomplish the result but this one is pretty easy and reversible.
Reply With Quote
  #18  
Old 01-04-2021, 07:03 PM
lefty_jake lefty_jake is offline
Member
1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires 1946 K-22 misfires  
Join Date: Jul 2015
Posts: 228
Likes: 135
Liked 245 Times in 127 Posts
Default

Quote:
Originally Posted by Jerry in SC View Post
I’ve removed the side plate and cleaned all the parts, the firing pin area looks nice and clean. Timing is perfect, the hammer fall feels a bit light.
If the hammer fall feels a bit light, this is likely the source of the problem. Rimfire rounds need a solid strike, and generally require a bit more mainspring tension than centerfire rounds.

I will second the suggestion to try a using the body of a spent primer as a shim on the end of the strain screw. There is a good chance it will resolve the issue.

I would also like to know the weight of the double action trigger pull. The pull weight gives a good approximation of the mainspring tension, so it provides an important clue about what is going on. If the pull weight is much below 10 lb on a rimfire, then that is suspect. If the trigger pull is already around 12 lb, then there likely is some other problem. Of course these numbers are not absolutes, but getting good measurements is still helpful.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
1946 m&p ME94 S&W Hand Ejectors: 1896 to 1961 9 09-07-2020 10:54 PM
1946 S&W RdrBill S&W Hand Ejectors: 1896 to 1961 10 04-25-2011 06:11 PM
1946 pre 10 sw44spl S&W Hand Ejectors: 1896 to 1961 5 04-24-2011 08:55 PM
1946 .38-44 HD swmod29 S&W Hand Ejectors: 1896 to 1961 5 05-23-2010 03:03 AM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 05:03 PM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)