|
|
01-17-2022, 03:21 PM
|
|
US Veteran
|
|
|
Join Date: Jun 2011
Location: the ready line, N. Idaho
Posts: 1,410
Likes: 927
Liked 1,764 Times in 734 Posts
|
|
M19-2 light trigger pull
My NTM (New to Me) 19-2, pristene bluing, tight cylinder gap (like .004), very happy with the timing, no end shake, etc, is light on the trigger pull ( will lift 2.75 lbs, but not 3lbs). I tested the main spring by lifting 4.25 lbs at the first step of the hammer below the hammer nose. I would like more t pull weight 3.5 or so. Q: Are the main spring and the rebound spring related in this operation. If I change rebound spring to heaver will it send balance out of wack. I know of no GS's in N Idaho to ask for help. I read that S&W standard rebound spring should be 18lbs. I have looked up a supplier and found 16 lb available only.
Is this bbl stud normal for a new -2? Or might it have been stretched by some master builder?
__________________
"Don't Give Up the Ship"
Last edited by pantannojack; 01-17-2022 at 09:31 PM.
|
01-17-2022, 03:37 PM
|
Vendor
|
|
|
Join Date: Jan 2010
Location: Kansas City area
Posts: 6,190
Likes: 54,459
Liked 13,612 Times in 4,290 Posts
|
|
The rebound spring is the main one involved in SA pull. The condition of the hammer and trigger SA sears are part of the equation, too. If you can cock the hammer and not have push off, the sears are probably OK. In that case, going to a heavier rebound spring will raise the SA trigger pull. If you want a factory rebound spring, I will send you one for the princely sum of your mailing address.
|
The Following 9 Users Like Post:
|
|
01-20-2022, 02:09 AM
|
|
Member
|
|
|
Join Date: Jul 2009
Location: Puget Sound
Posts: 616
Likes: 578
Liked 802 Times in 287 Posts
|
|
My 19-3 has a Wolff reduced power main spring and a 13# rebound spring installed. Less than 16# springs are definitely available.
|
The Following User Likes This Post:
|
|
01-20-2022, 05:44 AM
|
|
Member
|
|
|
Join Date: Apr 2006
Posts: 17,820
Likes: 7,852
Liked 25,742 Times in 8,697 Posts
|
|
16 pounds is MORE than heavy enough IMHO.
|
The Following User Likes This Post:
|
|
01-20-2022, 07:51 AM
|
|
US Veteran
|
|
|
Join Date: Jul 2010
Location: Denver, CO
Posts: 2,266
Likes: 858
Liked 4,405 Times in 1,084 Posts
|
|
The specification for single action trigger weight in my Smith & Wesson Armorers manual is 2.5 lbs. so you really are within spec.
Stu
|
01-20-2022, 10:03 AM
|
Member
|
|
|
Join Date: Mar 2012
Posts: 5,831
Likes: 3,902
Liked 5,902 Times in 2,543 Posts
|
|
Is that pic correct? Where's the infamous cut in the lower barrel face to accommodate the yoke?
__________________
Pickpocket
|
01-20-2022, 10:36 AM
|
Vendor
|
|
|
Join Date: Jan 2010
Location: Kansas City area
Posts: 6,190
Likes: 54,459
Liked 13,612 Times in 4,290 Posts
|
|
The new K frames don't have the flat cut on the bottom of the barrel.
|
01-20-2022, 11:56 AM
|
Member
|
|
|
Join Date: Mar 2012
Posts: 5,831
Likes: 3,902
Liked 5,902 Times in 2,543 Posts
|
|
Quote:
Originally Posted by Protocall_Design
The new K frames don't have the flat cut on the bottom of the barrel.
|
True, but isn't OP talking about a 19-2? I must've missed something...
__________________
Pickpocket
|
01-20-2022, 01:08 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,225
Likes: 484
Liked 11,390 Times in 3,522 Posts
|
|
This is the S&W SA trigger standard as of today, January 20th, 2022, according to S&W Customer Service representative "Dave".
It's impossible to say what it will be tomorrow.....
Smith & Wesson Support
10:59 AM (3 minutes ago)
to me
Hello,
The factory standard is 3-5 pounds for single action trigger poundage.
Regards,
Dave
__________________
Ret. LE, FA Instr, S&W Armorer
Last edited by armorer951; 01-20-2022 at 01:14 PM.
|
The Following User Likes This Post:
|
|
01-20-2022, 04:09 PM
|
Vendor
|
|
|
Join Date: Jan 2010
Location: Kansas City area
Posts: 6,190
Likes: 54,459
Liked 13,612 Times in 4,290 Posts
|
|
Quote:
Originally Posted by Hapworth
True, but isn't OP talking about a 19-2? I must've missed something...
|
You're right - I missed something, too. A 19-2 would have the flat.
|
01-20-2022, 04:18 PM
|
|
US Veteran
|
|
|
Join Date: Jul 2010
Location: Denver, CO
Posts: 2,266
Likes: 858
Liked 4,405 Times in 1,084 Posts
|
|
Armorer, indeed, all over the map. Here's the page from my Armorers manual.
Stu
|
The Following 3 Users Like Post:
|
|
01-20-2022, 04:51 PM
|
|
US Veteran
|
|
|
Join Date: Jun 2011
Location: the ready line, N. Idaho
Posts: 1,410
Likes: 927
Liked 1,764 Times in 734 Posts
|
|
Quote:
Originally Posted by Hapworth
Is that pic correct? Where's the infamous cut in the lower barrel face to accommodate the yoke?
|
Thank you for pointing that out. I never noticed. I mic'd the cylinder stud which rotates under the bbl stud at .400". I also mic'd a 10-5 cylinder stud with the bbl flat relief, at .420". Might that explain the difference, and does this indicate some custom assembly technique meant to not weaken the bbl? Upon receiving this piece from some online auction I was immediately impressed by the fresh high luster blue and the tightness of action. But there is a smudge beneath the finish on the side plate suggesting a reblue job. If so it is the nicest refinish I would ever hope to see. After sitting on it for a year, I have decided to use it as a shooter going no stronger than 6.5g Unique and 158g LSWC GC
__________________
"Don't Give Up the Ship"
|
The Following User Likes This Post:
|
|
|
Posting Rules
|
|
|
|
|