Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > S&W-Smithing
o

Notices

S&W-Smithing Maintenance, Repair, and Enhancement of Smith & Wesson and Other Firearms.


Reply
 
Thread Tools Display Modes
  #1  
Old 06-20-2009, 12:04 PM
lwt210 lwt210 is offline
Member
 
Join Date: May 2009
Posts: 13
Likes: 0
Liked 0 Times in 0 Posts
Default How does the hand spring fit on 442/642

Greetings and thanks in advance for any assistance.

But how does the hand spring install in a Smith 442/642?

I have one apart and can't figure out how that little spring goes back in.

Any help/links would be appreciated.
Reply With Quote
  #2  
Old 06-20-2009, 01:45 PM
500 Magnum Nut's Avatar
500 Magnum Nut 500 Magnum Nut is offline
Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: May 2004
Location: Connecticut, USA
Posts: 1,526
Likes: 0
Liked 143 Times in 48 Posts
Default

On the new MIM guns the hand spring is different. The pictures below is how it looks assembled. If it fly's apart, look at the pictures to aid you in reassembling it. Remember that there is a "blind" cutout area where the short side of the spring fits, inside the trigger. The other side of the spring gets bent behind the hand stud in the normal way and when all assembled it's fine. Remember, the spring fits on the side that the hand is positioned.


__________________
NRA Benefactor Member
Reply With Quote
The Following 3 Users Like Post:
  #3  
Old 06-20-2009, 02:51 PM
lwt210 lwt210 is offline
Member
 
Join Date: May 2009
Posts: 13
Likes: 0
Liked 0 Times in 0 Posts
Default

So trigger removal is pretty much mandatory?

I don't see anyway of fishing that thing in with the trigger installed.

If this is right, can you give me a guide on removing the trigger? I have removed just about everything else.

Thanks for the help.
Reply With Quote
  #4  
Old 06-20-2009, 04:29 PM
500 Magnum Nut's Avatar
500 Magnum Nut 500 Magnum Nut is offline
Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: May 2004
Location: Connecticut, USA
Posts: 1,526
Likes: 0
Liked 143 Times in 48 Posts
Default

These notes apply to all S&W revolvers. Only minor differences:
Find a perfect fitting screwdriver.

Remove the grip.

Unscrew all the screws on the side plate, don't mix them up.

Roll gun over, push the thumb latch in and open the cylinder.

Slide yoke and cylinder off the frame, go easy not to scratch it.

Roll gun back and find a plastic hammer and tap the frame (near where the grips would be) and the side plate will come loose.

Remove slide plate.

Lift out the hammer block (sheet metal part with a hole on one end, hook on the other CENTENIAL MODELS OMIT).

Loosen strain screw and remove main spring. (J frame insert cotter pin into hole, remove from stirrup).

Pull thumb piece to rear. Press trigger to cock hammer, lift hammer up and off the stud.

Find a screwdriver, and pry the rebound slide off the stud, rebound spring and stem will fly out so keep a finger over opening.

Pull back the hand to clear window, then wiggle trigger off the stud.

You can remove the cylinder stop and bolt but the gains are not worth the trouble.

But if you must, then flip gun over and unscrew thumb piece.

Flip gun back, pull bolt to rear and lift out of frame, watch out for plunger and tiny spring.

Pry out spring for cylinder stop, let the stop drop down and remove stop.

Reverse the operation to put it back together. Find a special rebound slide tool to put the rebound spring back on. It looks like this:


Remember all the guns from J frame to X are nearly all the same internally.

The hammer block sits all the way up before the slide plate goes back on. One end sits on the stud of the rebound slide, the other end sits in front of the hammer. Picture of 500:



Here is a picture of a 686 without the hammer block:
__________________
NRA Benefactor Member
Reply With Quote
  #5  
Old 06-20-2009, 09:31 PM
lwt210 lwt210 is offline
Member
 
Join Date: May 2009
Posts: 13
Likes: 0
Liked 0 Times in 0 Posts
Default

It's the wiggling the trigger off the stud part I am stuck at.

It doesn't want to budge.

Do I have to relieve the pressure of the trigger return spring to get the trigger and the part behind the trigger that encases the return spring out? Do these parts come out together?

Gonna give it a rest for today and hit it again fresh in the a.m. Starting to give me a headache.

Thanks again.
Reply With Quote
  #6  
Old 06-20-2009, 10:03 PM
lwt210 lwt210 is offline
Member
 
Join Date: May 2009
Posts: 13
Likes: 0
Liked 0 Times in 0 Posts
Default

Okay,


I got mad and wiggled that trigger off.

Now I am gonna attempt to get the hand back on the trigger. I may be seeing light at the end of the tunnel.
Reply With Quote
  #7  
Old 06-21-2009, 07:25 AM
lwt210 lwt210 is offline
Member
 
Join Date: May 2009
Posts: 13
Likes: 0
Liked 0 Times in 0 Posts
Default

Got her put back together now. All seems well but I have a shooting session planned for early Monday morning to ensure it is all right.

Many thanks to you sir for the help. The pics made all the difference.

That spring is a bear to get installed.
Reply With Quote
  #8  
Old 07-26-2009, 01:38 PM
DCWilson's Avatar
DCWilson DCWilson is offline
SWCA Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: Dec 2007
Location: Orange County, CA
Posts: 13,991
Likes: 4,996
Liked 7,678 Times in 2,616 Posts
Default MIM trigger in 296 and fitting hand spring

Let me just add a word to 500 Magnum Nut's excellent post No. 2 above about hand springs inside MIM triggers. The 296 I was just tinkering with has a smaller and less complex configuration than the one in his example, and it took me longer than it should have to extrapolate from his pictures to my situation. Fitting the hand spring turns out to be simple if you know how to approach it, and an exercise in frustration if you just monkey around with it in the dark. Recommendation: if you have old eyes like mine, do this in a deep box in bright sunlight or under heavy desktop task lighting.

The hand spring has a short arm and a long arm. Put the short arm into the blind pocket that 500MN mentioned, and make sure the coil in the spring is back against the metal of the trigger; there is a semi-circular relief in the MIM part to accommodate it.

Then using a pin punch or narrow bladed screwdriver the same width as the slot in the trigger, push the long end of the hand spring back far enough to slip the two pegs of the hand into their holes in the trigger.

Then with the hand firmly seated, release pressure on the spring and you are good to go.

Sorry, no pictures. The next time I take the gun apart I will try to remember to take some. But really, if you remember short end down and coil against the metal, that's all you need to know to make reinstallation of the hand spring work.
__________________
David Wilson

Last edited by DCWilson; 04-17-2013 at 12:34 PM. Reason: fix duplicated word
Reply With Quote
The Following 4 Users Like Post:
  #9  
Old 07-29-2009, 07:13 PM
allglock allglock is offline
Banned
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: Nov 2001
Location: Se. Pa.
Posts: 1,330
Likes: 67
Liked 81 Times in 50 Posts
Default

Tagged for future reference.
Reply With Quote
  #10  
Old 08-01-2009, 11:24 PM
bodger's Avatar
bodger bodger is offline
US Veteran
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: May 2009
Location: los angeles
Posts: 6
Likes: 0
Liked 1 Time in 1 Post
Default

Quote:
Originally Posted by allglock View Post
Tagged for future reference.
+1 to that. I just took apart my Model 66 for the first time. That hand torsion spring is a little beetch to get back in there.

edit to add: I talked to a gunsmith who has devised a wire tool that makes holding the spring in position a lot easier than the screwdriver trick.

He attaches the wire to the bench with a screw, then loops the other end over the spring arm that needs to be forward of the pegs, and pulls back on the trigger assembly
whilst he inserts the hand into the trigger.
neat.

Last edited by bodger; 08-03-2009 at 01:28 PM.
Reply With Quote
The Following User Likes This Post:
  #11  
Old 04-14-2010, 08:19 PM
mgraff mgraff is offline
Member
 
Join Date: May 2008
Location: Wyoming
Posts: 2
Likes: 0
Liked 0 Times in 0 Posts
Default

Quote:
Originally Posted by allglock View Post
Tagged for future reference.
+2 I guess! great info thanks
Reply With Quote
  #12  
Old 04-27-2010, 03:23 PM
BE Mike's Avatar
BE Mike BE Mike is offline
Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: Sep 2003
Location: Indiana
Posts: 3,567
Likes: 2,230
Liked 3,461 Times in 1,469 Posts
Default

I've been replacing the springs on my father's 642. He is getting up in age and doesn't have the strength to pull a hard double action pull any more. Although I've worked on a lot of the older S&W revolvers, I have limited experience with those with MIM parts. I can't tell you just how much help this thread has been in getting the hand spring back in place. It can't be stressed too much just how important it is to get the short leg of that spring solidly in that blind hole in the trigger. Muchisimas gracias!
Reply With Quote
  #13  
Old 05-08-2011, 10:37 AM
otis2011 otis2011 is offline
Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: May 2011
Posts: 10
Likes: 0
Liked 2 Times in 2 Posts
Default

+1 to entire thread!


I know I am late to the party, but I'm sure others will view this thread going forward, wanted to share my experience.

I have a 642-2 and wanted to remove the lock mechanism. A little too exuberant in removing the hammer and the spring popped from the hand. Doh!!!

Took me a while to find the hidden pocket. Bright task lighting was critical for this discovery. Once I discovered the pocket, the pictures made a lot more sense to me, making the assembly more logical.

Found that a flat end allen wrench (vs. the ball ends I have so many of) that was small enough to fit into the slot and large enough to fill most of the slot worked very well for pushing the spring back to get behind the hand pins.

Thanks to all for your help in this perplexing challenge. Have the pistol back together now (whew!!!) and am ready to go to the range to run it again, to make certain my assembly technique was correct.

Last edited by otis2011; 05-08-2011 at 10:40 AM.
Reply With Quote
The Following User Likes This Post:
  #14  
Old 05-09-2011, 11:44 PM
Kwizard Kwizard is offline
Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: May 2011
Posts: 9
Likes: 0
Liked 1 Time in 1 Post
Default Thanks!

Just wanted to say thanks to all that contributed to this thread. The comments and photos were invaluable when I was reassembling my 60 after putting lighter main and rebound springs in.
Reply With Quote
The Following User Likes This Post:
  #15  
Old 09-19-2012, 06:03 PM
jackpearl jackpearl is offline
Member
How does the hand spring fit on 442/642  
Join Date: Jan 2006
Location: Coast of Maine
Posts: 221
Likes: 199
Liked 30 Times in 22 Posts
Default

Thanks!! Fooled with this for an hour before I found these pictures, ten minuets later, All back together!!
__________________
NRA Life Member
AF&AM #129
Reply With Quote
  #16  
Old 09-19-2012, 07:43 PM
H Richard's Avatar
H Richard H Richard is offline
US Veteran
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: Aug 2006
Location: West Central IL
Posts: 22,758
Likes: 18,437
Liked 22,311 Times in 8,245 Posts
Default

There is very seldom a reason to remove the "hand" from the trigger, just leave it in place when you remove the trigger. Only when you need to work on the hand do you need to remove it.
__________________
H Richard
SWCA1967 SWHF244
Reply With Quote
The Following User Likes This Post:
  #17  
Old 09-19-2012, 11:04 PM
jackpearl jackpearl is offline
Member
How does the hand spring fit on 442/642  
Join Date: Jan 2006
Location: Coast of Maine
Posts: 221
Likes: 199
Liked 30 Times in 22 Posts
Default

Quote:
Originally Posted by H Richard View Post
There is very seldom a reason to remove the "hand" from the trigger, just leave it in place when you remove the trigger. Only when you need to work on the hand do you need to remove it.
Agreed. Had to smooth some sharp edges on my 625 hand. I pulled the hand out of the trigger and suddenly realized, this isn't like the rest.
__________________
NRA Life Member
AF&AM #129
Reply With Quote
  #18  
Old 05-30-2015, 10:33 AM
RaylanGivens's Avatar
RaylanGivens RaylanGivens is offline
Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: Mar 2013
Location: Richardson, Texas
Posts: 217
Likes: 95
Liked 192 Times in 65 Posts
Default

Otis211 thanks for the Allen wrench idea. I an enrolled in an NRA Smith and Wesson Revolver Armorers class to be held in June.so I took the side plate off an old .38 M&P. I had never removed a side plate. I certainly learned a lot of helpful info by doing that. The only issue I had was getting the hand back into the trigger. This thread came up when I did a search. The Allen wrench did the trick. Thanks to all who contributed. The pictures were a great help. This forum is amazing. There a good people here who have the info we need when we need it.
__________________
I'm just buying one more.
Reply With Quote
The Following User Likes This Post:
  #19  
Old 06-01-2015, 07:11 PM
Boogsawaste's Avatar
Boogsawaste Boogsawaste is offline
Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: Jun 2013
Location: Quakertown PA
Posts: 1,466
Likes: 4,742
Liked 1,172 Times in 486 Posts
Default

I also use the allen wrench trick. Works beautifully!
__________________
Jim
Reply With Quote
The Following User Likes This Post:
  #20  
Old 08-16-2015, 12:56 PM
dyna962007 dyna962007 is offline
Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: Jan 2015
Location: STL MO area
Posts: 57
Likes: 2
Liked 4 Times in 4 Posts
Default schematics

One of the biggest problems Ive had with this and other projects on these newer guns is the lack of schematics that pertain to this specific gun.
I have a 686-6 and have looked everywhere, at all the sights including S and W to find a parts breakdown for it. Not a -5, not a dash 4 but one for a 686-6.
I am trying to buy some new hand springs and can get a straight answer on what the part number is or where to even buy it.
Id also like to buy a new hand but that may be more than the system can handle.
__________________
Former LEO & firearms trainer
Reply With Quote
  #21  
Old 05-21-2016, 09:17 PM
ryker411 ryker411 is offline
Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: Nov 2010
Posts: 10
Likes: 1
Liked 39 Times in 3 Posts
Default

Nerve saving thread. Thank you for this one!!!!
Reply With Quote
  #22  
Old 06-23-2016, 10:50 AM
46Slick 46Slick is offline
Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: Jan 2013
Posts: 8
Likes: 4
Liked 2 Times in 1 Post
Default

My 642-1 had a problem with the cylinder not revolving after installing an Apex spring kit. I found that little spring in the trigger that tensions the hand. I had no clue on how to assemble the spring back in. Gave up over night. A new Google this am led me to this thread. The pictures gave me the insight to re-assemble the hand spring. My gun did not quite match the pictures but the idea was there. Good to go now. Thanx to the poster.
Reply With Quote
  #23  
Old 10-08-2016, 07:12 PM
jringo8769's Avatar
jringo8769 jringo8769 is offline
Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: Jan 2012
Location: Jamestown NY
Posts: 813
Likes: 7,785
Liked 518 Times in 281 Posts
Default

well i want to thank u ....i spent part of my day trying to fix my Dad's gun and this was just what i was looking for...thank u and God Bless,John
Reply With Quote
  #24  
Old 03-07-2017, 10:38 PM
hard hard is offline
Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: Mar 2017
Posts: 3
Likes: 3
Liked 1 Time in 1 Post
Default success

Quote:
Originally Posted by 500 Magnum Nut View Post
On the new MIM guns the hand spring is different. The pictures below is how it looks assembled. If it fly's apart, look at the pictures to aid you in reassembling it. Remember that there is a "blind" cutout area where the short side of the spring fits, inside the trigger. The other side of the spring gets bent behind the hand stud in the normal way and when all assembled it's fine. Remember, the spring fits on the side that the hand is positioned.


Got it thanks
Reply With Quote
The Following User Likes This Post:
  #25  
Old 06-15-2017, 08:28 PM
aryfrosty's Avatar
aryfrosty aryfrosty is offline
Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: Mar 2011
Location: Huntsville, Alabama
Posts: 34
Likes: 6
Liked 2 Times in 2 Posts
Default

Quote:
Originally Posted by 500 Magnum Nut View Post
These notes apply to all S&W revolvers. Only minor differences:
Find a perfect fitting screwdriver.
Thank you for the photos. I am apparently in a condition of dotage but by using your photos I was able to get the hand spring back in place.
Reply With Quote
  #26  
Old 08-07-2017, 07:28 PM
Ten32's Avatar
Ten32 Ten32 is offline
Member
How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642 How does the hand spring fit on 442/642  
Join Date: Mar 2015
Location: PA
Posts: 3
Likes: 3
Liked 2 Times in 2 Posts
Default

Could someone please repost the pics, the links are dead...and my 340 is in pieces. Thanks!

Sent from my SM-G930V using Tapatalk
Reply With Quote
Reply

Tags
442, 642, 686, gunsmith, j frame, lock, model 40, model 66, screwdriver

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Late 40s M&P Hand, Hand Lever, & Spring wamalo S&W-Smithing 2 07-24-2017 03:33 PM
Need 625 Hand Spring keno WANTED to Buy 1 04-24-2014 11:27 AM
hand spring on a 686 smallspook S&W Revolvers: 1980 to the Present 3 04-22-2013 04:04 PM
642 hand spring TGDKYSER S&W Revolvers: 1980 to the Present 0 07-07-2012 06:49 PM
Need help with Hand Spring jimonfly S&W-Smithing 6 08-17-2010 10:46 AM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 05:32 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)