long fake suppressor

pyper22 · #1 12-02-2011, 09:08 PM

where can i get one of these , i have seen them but don't remember where. i want one that don't make the bbl. any longer ,, it would be for a threaded bbl. thanks, pyper22.

GonzoTX · #2 12-02-2011, 09:23 PM

Tacticool22

Dragon88 · #3 12-02-2011, 09:28 PM

See posts 3 and 4 in this thread:

*** 15-22 Specific CLASSIFIEDS ***

pyper22 · #4 12-02-2011, 10:40 PM

thank's guy's , pyper22

AirborneDaddy · #5 12-03-2011, 05:50 PM

Spikes tactical

tacticool22 · #6 12-04-2011, 01:31 PM

Thanks GonzoTX
pyper22 if you want a finely made shroud that gives your rifle that integrally suppressed look and has a great finish and no advertising on it, then check out Barrel Shrouds : Tacticool22, Tactical .22 Rifle Parts and Accessories
Your rifle will be shorter than it is with the flash hider.

shotsfired · #7 12-04-2011, 02:36 PM

can u get me all info on your shrouds, thanks.

tacticool22 · #8 12-04-2011, 02:52 PM

All the info is on that link. If there is something missing, please let me know so I can add that information.
Or if something is not clear, let me know so I can fix that too.

pyper22 · #9 12-04-2011, 08:30 PM

Quote:

Originally Posted by tacticool22

Thanks GonzoTX
pyper22 if you want a finely made shroud that gives your rifle that integrally suppressed look and has a great finish and no advertising on it, then check out Barrel Shrouds : Tacticool22, Tactical .22 Rifle Parts and Accessories
Your rifle will be shorter than it is with the flash hider.

thanks, tacticool. question. how do i tightened the shroud, if it covers all of my bbl. i made a bbl. vise out of a block of teflon, to remove the threaded flash hider, or whatever it is called. but how do i torque the shroud with the org. hand guard. , thanks. pyper22.

tacticool22 · #10 12-05-2011, 02:17 AM

Hand tight with a crush washer is fine. I have one that I don't even use the crush washer. Just hand tight with a glove, those grippy rubber dipped gardening kind, and it stays tight.

ChattanoogaPhil · #11 12-05-2011, 09:22 AM

I swap around muzzle devices quite a bit on my .22s and just hand tighten them.

pyper22 · #12 12-05-2011, 05:21 PM

Quote:

Originally Posted by tacticool22

Hand tight with a crush washer is fine. I have one that I don't even use the crush washer. Just hand tight with a glove, those grippy rubber dipped gardening kind, and it stays tight.

thanks . that is what i thuought i would try. pyper22

TargetSher · #13 12-07-2011, 10:51 PM

Are we talking about the shroud set screw or receiver? Great product Tacticool, I'll be ordering soon.

pyper22 · #14 12-11-2011, 11:48 PM

Quote:

Originally Posted by TargetSher

Are we talking about the shroud set screw or receiver? Great product Tacticool, I'll be ordering soon.

we talking about the threaded shroud with the flash supp. removed.and it would go a little ways in to the hand guard. with the insert removed. pyper22

pyper22 · #15 12-11-2011, 11:50 PM

Quote:

Originally Posted by tacticool22

Thanks GonzoTX
pyper22 if you want a finely made shroud that gives your rifle that integrally suppressed look and has a great finish and no advertising on it, then check out Barrel Shrouds : Tacticool22, Tactical .22 Rifle Parts and Accessories
Your rifle will be shorter than it is with the flash hider.

would it be less than 16"? that is a nono. pyper22

tacticool22 · #16 12-12-2011, 12:27 AM

The overall length is 5/8" less than with a standard A1 or A2 flash hider.
A standard 15-22 has a 16.5 inch barrel, threaded or not. Even though all the literature says 16" barrel.
Here is a link to how the ATF measures barrel length http://www.atf.gov/publications/down...-chapter-2.pdf

Hole Fire · #17 12-16-2011, 09:57 PM

Quote:

Originally Posted by tacticool22

Thanks GonzoTX
pyper22 if you want a finely made shroud that gives your rifle that integrally suppressed look and has a great finish and no advertising on it, then check out Barrel Shrouds : Tacticool22, Tactical .22 Rifle Parts and Accessories
Your rifle will be shorter than it is with the flash hider.

Love the look, awsome, my concern is heat, will this cause the barrel to heat up faster,dont no anything about them just concerned about extra heat on barrel affecting groups!

GonzoTX · #18 12-17-2011, 12:26 AM

the flash hider comes of easy, well at least for my rifle. all I did was put some duck tape of the flash hider and put a crescent wrench on it, and then just tapped it with a rubber mallet. It was easy and then just hand tight the fake can with a glove.

tacticool22 · #19 12-17-2011, 02:10 PM

Quote:

Originally Posted by Hole Fire

Love the look, awsome, my concern is heat, will this cause the barrel to heat up faster,dont no anything about them just concerned about extra heat on barrel affecting groups!

There is no problem with heat. Unless you are running full auto, or pretty close to it, and hundreds of rounds at a time.
As far as heating up faster, I doubt it. The larger surface area of the aluminum shroud will transfer heat to the atmosphere faster than the steel of the barrel.
It's all theoretical. If you want to test it, get a thermal camera and do some video.