|
|
09-06-2017, 02:09 PM
|
Member
|
|
|
Join Date: Sep 2017
Posts: 2
Likes: 1
Liked 0 Times in 0 Posts
|
|
New Member/15-22 owner
Hi all
Sorry for the newbie question's but i'd rather find this information out before wasting money. Is there a kit people recommend for cleaning the 15-22 sport 2? I realize its not rocket science but if there is some sort of combo that works well i'd love to know about. I've heard people talk about bore snakes. If i were to purchase everything i need by its self, what all should i buy?
Also this and a mossberg 500 20 gauge are the only firearms i own. I just took them out to the range yesterday for the first time. I was having trouble getting shots where i "thought" i was aiming with the 15-22 ( still using stock mbus sights ). Seemed like no matter how i adjusted them, my shots were always going down and to the right. I might have not been putting my face close enough to the stock to see through them properly. Once again, I'm very new to this and from what i read it might have been that was trying to shoot something too close.
|
09-06-2017, 04:03 PM
|
Member
|
|
|
Join Date: Jul 2017
Posts: 12
Likes: 22
Liked 14 Times in 8 Posts
|
|
Hi and welcome!
I have a bore snake for cleaning and never have to do more than two passes even after hundreds of rounds of Thunderbolt (a really dirty ammo that your 15-22 manual tells you to never use). For cleaning the rest of the gun I use microfiber cloths, and cotton swabs.
If your shots are landing in the same place after adjusting your sights it is possible you are inadvertently jerking the gun when pulling the trigger. Try to rest the gun on something or shoot with your left hand to rule it out. Either that or you need to adjust them further. I actually replaced the springs on my trigger with lighter springs to make the trigger pull lighter, since I tend to jerk guns with heavier triggers.
|
The Following User Likes This Post:
|
|
09-06-2017, 05:21 PM
|
Member
|
|
|
Join Date: Sep 2017
Posts: 2
Likes: 1
Liked 0 Times in 0 Posts
|
|
Cool, thank you for that info. Is there a certain bore snake you'd recommend? Also, which type of cleaning products should be used to clean the metal parts of the 15-22?
|
09-06-2017, 10:17 PM
|
Member
|
|
|
Join Date: May 2014
Location: North Texas
Posts: 1,596
Likes: 2,455
Liked 1,148 Times in 608 Posts
|
|
Breakfree CLP is an old standby that will work fine, but there are plenty of good cleaning products. I like Hoppes bore snakes, and would trust Otis although I haven't used one yet. I also do a few passes with the bore snake then clean the parts with Breakfree and swabs. Welcome to the forum!
|
09-06-2017, 11:18 PM
|
Member
|
|
|
Join Date: Mar 2014
Location: The Rugged Llano Estacado
Posts: 3,618
Likes: 21,629
Liked 5,444 Times in 2,245 Posts
|
|
I've only used Hoppe's bore snakes, but I understand Otis makes good ones too. I use Hoppe's #9 cleaner, but pretty much any gun cleaner will work. There are dozens to choose from.
To clean the breech face and the bolt I use Q tips dipped in Hoppe's, a shop towel, and an old toothbrush. The 15-22 doesn't need much oil. Just a drop on each bolt rail. If you choose CLP for cleaning, you can use it as lubricant as well. If you use another solvent you'll want some oil. Pretty much any brand will do. I have Hoppe's and Otis.
__________________
Or something like that . . .
|
09-06-2017, 11:50 PM
|
Member
|
|
|
Join Date: May 2016
Location: Devon, UK
Posts: 67
Likes: 105
Liked 43 Times in 30 Posts
|
|
Also check the barrel isn't loose as they have been known to be loose from the factory.
|
The Following User Likes This Post:
|
|
09-07-2017, 10:03 AM
|
Member
|
|
|
Join Date: Jan 2016
Posts: 112
Likes: 2
Liked 54 Times in 37 Posts
|
|
When using a Boresnake, just be careful that it doesn't snag on the ejector, which could bend it out of whack. I'll usually just put one finger over the rearmost end of the ejector until the Boresnake's end loop clears.
Quote:
Seemed like no matter how i adjusted them, my shots were always going down and to the right. I might have not been putting my face close enough to the stock to see through them properly.
|
Iron sight shooting is a bit of an art form. Having a knowledgeable person there to train you is very helpful. Putting the tip of your nose to the back of the charging handle should give you the proper eye relief to the rear sight, then focus on the front sight and add pressure to the trigger.
|
09-16-2017, 06:37 PM
|
Member
|
|
|
Join Date: Sep 2017
Posts: 6
Likes: 0
Liked 2 Times in 2 Posts
|
|
9 dollar kit with 2 dollar 22 brass bore
|
09-16-2017, 07:02 PM
|
Member
|
|
|
Join Date: Oct 2016
Location: East Texas
Posts: 283
Likes: 99
Liked 164 Times in 101 Posts
|
|
Any cleaning products that are made for cleaning guns should work just fine. As to the sights, I'm wondering if you're adjusting them the opposite of how they should go. Since your problem continues after adjusting. As was posted earlier, there have been rifles shipped from the factory that have loose barrels. Although unlikely, that would also cause your problem.
Newbie questions aren't a problem, we're here to help a fellow enthusiast if possible. Keep us posted on any progress.
And welcome to the forum!
|
09-17-2017, 03:00 PM
|
Member
|
|
|
Join Date: May 2017
Location: Alabama
Posts: 724
Likes: 476
Liked 387 Times in 261 Posts
|
|
Regarding the MBUS adjustments, in case you want the gospel from Magpul, here you go:
"The amount each click will move your point of aim depends on the distance between the front and rear sight. According to Magpul, the rear sight adjusts ~0.7 MOA per click with a 14.5″ sight radius and ~0.5 MOA (0.547″/100m) per click with a 20″ sight radius. The front sight adjusts ~1.6 MOA per click with a 14.5″ sight radius, and ~1.2 MOA per click with a 20″ sight radius."
You can go with the 14.5" sight radius though measuring mine, I get 14.375" measuring from rear of rear sight to front of front sight post.
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
|
|
|
|