|
|
03-05-2018, 04:57 PM
|
Member
|
|
|
Join Date: Aug 2010
Location: Austin, TX
Posts: 260
Likes: 171
Liked 123 Times in 65 Posts
|
|
Beware of the Evil Bolt Roll Pin!
You must use a punch small enough to enter the opening where the roll pin is located, large enough to engage the sides of the roll pin which is hollow but large enough not to slip into the opening of the roll pin, get stuck and destroy the pin. Don't ask as how I became such an expert
|
The Following User Likes This Post:
|
|
03-05-2018, 06:37 PM
|
Member
|
|
|
Join Date: Mar 2015
Location: Anchorage, AK
Posts: 25
Likes: 7
Liked 29 Times in 14 Posts
|
|
Wheeler makes a set of roll pin punches that have a nub to fit the hole and a ledge to fit the sides. They are typically the same size punch as the hole so you shouldn’t have a problem getting it in there. Wheeler makes a set of just punches and they also make an AR toolset that has the punches that you probably need for the 15-22 plus a bunch of other handy to have stuff... worthwhile kits.
Sent from my iPhone using Tapatalk
|
The Following 3 Users Like Post:
|
|
03-05-2018, 07:03 PM
|
US Veteran
|
|
|
Join Date: Feb 2009
Location: Ozarks of Missouri
Posts: 3,329
Likes: 3,009
Liked 2,922 Times in 992 Posts
|
|
Quote:
Originally Posted by lancehankins
Wheeler makes a set of roll pin punches that have a nub to fit the hole and a ledge to fit the sides. They are typically the same size punch as the hole so you shouldn’t have a problem getting it in there.
|
Here is what one looks like . . .
Russ
|
The Following User Likes This Post:
|
|
03-05-2018, 07:54 PM
|
Member
|
|
|
Join Date: Aug 2010
Location: Austin, TX
Posts: 260
Likes: 171
Liked 123 Times in 65 Posts
|
|
thanks just what i needed
|
03-06-2018, 01:36 AM
|
|
Member
|
|
|
Join Date: Jan 2014
Location: Utah
Posts: 1,966
Likes: 2,383
Liked 2,954 Times in 1,054 Posts
|
|
Not only are specific roll pin (nubbed) punches in the set, but there is also (usually) a double ended roll pin starter, large on one end and small on the other. It will drive a pin into its channel and leave about 1/4” sticking out. You can use the appropriate punch to finish seating the pin without damaging it. Quicker and easier. Worth the money. Proper tools for the job.
|
The Following User Likes This Post:
|
|
03-06-2018, 05:14 AM
|
|
Member
|
|
|
Join Date: Aug 2003
Location: West Central FL
Posts: 744
Likes: 761
Liked 448 Times in 284 Posts
|
|
3/32nds is the correct size for the bolt roll pin. Also a little tip I learned; don't drive it all the way out, just enough to release the firing pin (under spring pressure) and the recoil spring guide. This will make re-installation a breeze so your not fighting it to keep it straight.
|
The Following 3 Users Like Post:
|
|
03-06-2018, 09:57 AM
|
Member
|
|
|
Join Date: Aug 2010
Location: Austin, TX
Posts: 260
Likes: 171
Liked 123 Times in 65 Posts
|
|
Quote:
Originally Posted by CB3
Not only are specific roll pin (nubbed) punches in the set, but there is also (usually) a double ended roll pin starter, large on one end and small on the other. It will drive a pin into its channel and leave about 1/4” sticking out. You can use the appropriate punch to finish seating the pin without damaging it. Quicker and easier. Worth the money. Proper tools for the job.
|
Yes. I eventually learn! Actually this is the first gun I have that has a "roll pin" that I can think of. Wasn't aware of the need for a special tool. After a few "wacks" with a hammer and normal punch I became "aware".
|
03-06-2018, 09:59 AM
|
Member
|
|
|
Join Date: Aug 2010
Location: Austin, TX
Posts: 260
Likes: 171
Liked 123 Times in 65 Posts
|
|
Quote:
Originally Posted by cjt50
3/32nds is the correct size for the bolt roll pin. Also a little tip I learned; don't drive it all the way out, just enough to release the firing pin (under spring pressure) and the recoil spring guide. This will make re-installation a breeze so your not fighting it to keep it straight.
|
Thanks. Saw a YT video also recommending not to completely drive out the pin.
|
03-06-2018, 10:03 AM
|
|
Member
|
|
|
Join Date: Feb 2016
Posts: 1,576
Likes: 1,730
Liked 2,731 Times in 868 Posts
|
|
There is tuition cost for becoming a home gun smith, especially for the labs. How I know this.
|
03-06-2018, 10:06 AM
|
Member
|
|
|
Join Date: Aug 2010
Location: Austin, TX
Posts: 260
Likes: 171
Liked 123 Times in 65 Posts
|
|
|
The Following User Likes This Post:
|
|
03-06-2018, 12:01 PM
|
|
Member
|
|
|
Join Date: Jan 2014
Location: Utah
Posts: 1,966
Likes: 2,383
Liked 2,954 Times in 1,054 Posts
|
|
|
03-06-2018, 01:16 PM
|
Member
|
|
|
Join Date: Mar 2014
Location: The Rugged Llano Estacado
Posts: 3,618
Likes: 21,634
Liked 5,446 Times in 2,247 Posts
|
|
I guess I was just plain lucky. I replaced my firing pin by driving the roll pin (mostly) out with a nail the right size. I did clip the point off first. Worked like a charm for me, but I know it was a "bubba" job.
Got to get some real punches soon. Well, I have a couple, but neither was the right size.
__________________
Or something like that . . .
|
03-06-2018, 01:30 PM
|
Member
|
|
|
Join Date: Apr 2016
Posts: 1,464
Likes: 3,979
Liked 2,918 Times in 803 Posts
|
|
I'm not familiar with the .22 caliber AR15, is this roll pin the same as the cotter pin type firing pin retaining pin in the .223 version?
|
03-06-2018, 05:12 PM
|
Member
|
|
|
Join Date: Aug 2010
Location: Austin, TX
Posts: 260
Likes: 171
Liked 123 Times in 65 Posts
|
|
Quote:
Originally Posted by TX-Dennis
I guess I was just plain lucky. I replaced my firing pin by driving the roll pin (mostly) out with a nail the right size. I did clip the point off first. Worked like a charm for me, but I know it was a "bubba" job.
Got to get some real punches soon. Well, I have a couple, but neither was the right size.
|
I recommend not using a regular punch like I did. It was "almost" the perfect size which resulted in the bolt visiting my gunsmith to remove the "almost perfect punch" A roll pin punch would have avoided this drama.
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
|
|
|
|