|
|
01-17-2013, 02:17 PM
|
Member
|
|
|
Join Date: Nov 2012
Location: Kansas City
Posts: 104
Likes: 15
Liked 30 Times in 18 Posts
|
|
Small pin on slide
I forget what this pin is called, but it holds are the striker-fired parts in place, and you can see it on the top of the slide and on the underneath side. To do a complete disassembly of pistol (Shield and other M&P's) you punch this out of the slide. What is it called? And where do I find a replacement?
|
01-17-2013, 02:33 PM
|
|
US Veteran
|
|
|
Join Date: Oct 2012
Location: Waterford, Michigan
Posts: 1,753
Likes: 772
Liked 959 Times in 516 Posts
|
|
Are you referring to the extractor pin? That's the only pin on the slide that you need to punch out. This only allows you to remove the extractor and its spring. The internals of the slide are removed by the backplate and the removal of the rear sight. Contact Smith and Wesson for replacement pin.
__________________
M&P40c/15-22/SD9VE/Mossy500
|
01-17-2013, 03:44 PM
|
Member
|
|
|
Join Date: Nov 2012
Location: Kansas City
Posts: 104
Likes: 15
Liked 30 Times in 18 Posts
|
|
Yes, thanks. Just wanted to know terminology.
|
01-17-2013, 08:43 PM
|
Member
|
|
|
Join Date: Jun 2012
Location: Sarasota FL
Posts: 1,425
Likes: 3
Liked 517 Times in 297 Posts
|
|
It is a roll pin, if you are referring to the pin that holds the whole sear assembly in. The pin goes through the frame (holes on each side of the frame). You can get them from S&W parts. They call it a coil pin. Or you can take it to the hardware and see if they have a similar one. It will have to match the outside diameter, but if it is too long, you can grind it down to the correct length.
Bob
Last edited by robkarrob; 01-17-2013 at 08:53 PM.
|
01-17-2013, 08:54 PM
|
|
US Veteran
|
|
|
Join Date: Oct 2012
Location: Waterford, Michigan
Posts: 1,753
Likes: 772
Liked 959 Times in 516 Posts
|
|
Quote:
Originally Posted by robkarrob
It is a roll pin, if you are referring to the pin that holds the whole sear assembly in. The pin goes through the frame (holes on each side of the frame). You can get them from S&W parts. They call it a coil pin. Or you can take it to the hardware and see if they have a similar one. It will have to match the outside diameter, but if it is too long, you can grind it down to the correct length.
Bob
|
He's talking about the vertical pin in the SLIDE.
__________________
M&P40c/15-22/SD9VE/Mossy500
|
01-17-2013, 10:33 PM
|
Member
|
|
|
Join Date: Jun 2012
Location: Sarasota FL
Posts: 1,425
Likes: 3
Liked 517 Times in 297 Posts
|
|
Easier way than going through all these explanations.
Bob
|
01-17-2013, 10:58 PM
|
Member
|
|
|
Join Date: Jan 2011
Posts: 19
Likes: 7
Liked 18 Times in 6 Posts
|
|
In the early models, this pin is solid and extremely difficult to get out. It is a roll pin in most models, though, and S&W recommends replacing it if you take it out. There's not much of a reason to take it out if the extractor's not messed up.
|
01-17-2013, 11:30 PM
|
Member
|
|
|
Join Date: Nov 2012
Location: Kansas City
Posts: 104
Likes: 15
Liked 30 Times in 18 Posts
|
|
Bob, I'm talking about the extractor pin not the roll pin that holds in the sear assembly. Thank you for the thought though.
|
|
Posting Rules
|
|
|
|
|
All times are GMT -4. The time now is 12:52 PM.