Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Rifles and Shotguns > Smith & Wesson M&P10 Rifles
o

Notices

Smith & Wesson M&P10 Rifles Dedicated to the Smith & Wesson M&P-10 Rifles


Reply
 
Thread Tools Display Modes
  #1  
Old 04-18-2014, 06:41 PM
Boondocks Boondocks is offline
Member
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Apr 2014
Posts: 4
Likes: 0
Liked 1 Time in 1 Post
Default M&P10 firing pin issue

Here's a 'disconcerting' situation. After about 60 rounds through my new rifle over a week or so, the bolt failed to retract fully after firing a round. I opened the receiver and tried to extract the bolt but it 'dragged' severely as I pulled it out. When I examined the bolt I found that 'cam' that the firing pin passes through was under some spring tension that didn't allow it to be in the full upright position. That's why it dragged against the inside of the receiver and made it difficult to remove. I tried to pull the firing pin out of the bolt and it wouldn't budge. Thinking the firing pin might be broken, I took the rifle to my gunsmith (a fine Marine who knows everything about ARs). He was non-plussed when he couldn't remove the firing pin. Finally with a small needle-nose pliers he was able the grasp the firing pin and wedge it out. It wasn't broken. The spring around the pin was tightly compressed and had tightly wedged the firing pin in the bolt.

He was surprised to see a spring on the firing pin, as was I. Diameter of the ends of the spring are not the same so it apparently only goes on one way. I'm not sure which, except that maybe the larger end is supposed to slip over the back of the firing pin.

End of long story...I would not want this event to occur when I was trying to shoot something or somebody. Gun would be totally out of commission. So, anybody else have this happen? At least now you know that it can happen with the M&P10. I wonder when this is going to happen again with my rifle! And if one of you guys can check your firing pin spring, let me know which end goes on the pin first! I assume the spring is there to preclude slam-fires????
Reply With Quote
  #2  
Old 04-18-2014, 08:14 PM
webfarmer's Avatar
webfarmer webfarmer is offline
Member
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Apr 2013
Location: Michigan
Posts: 491
Likes: 271
Liked 146 Times in 105 Posts
Default

Yes, the spring is to eliminate slam fire issues. I can't go take mine down right now but I can relay I've not had the problem. Firing pin with spring comes out easily each time I clean the rifle. Round count is only at 190 so this info might not be any help to you. Good luck!
Reply With Quote
  #3  
Old 04-18-2014, 08:45 PM
Boondocks Boondocks is offline
Member
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Apr 2014
Posts: 4
Likes: 0
Liked 1 Time in 1 Post
Default

Thanks, Webfarmer! If you do get a chance to check that spring, please advise which end goes on pin first.
Reply With Quote
  #4  
Old 04-19-2014, 10:40 PM
webfarmer's Avatar
webfarmer webfarmer is offline
Member
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Apr 2013
Location: Michigan
Posts: 491
Likes: 271
Liked 146 Times in 105 Posts
Default

Boondocks, the small end goes on the firing pin first. I see the firing pin is tapered where the spring is placed. Small end toward where the hammer strikes - large end toward the primer. Hope that helps!
Reply With Quote
The Following 2 Users Like Post:
  #5  
Old 04-21-2014, 09:55 AM
Boondocks Boondocks is offline
Member
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Apr 2014
Posts: 4
Likes: 0
Liked 1 Time in 1 Post
Default Spring position on firing pin

Thanks for letting me know proper position of the firing pin spring! We had it reversed, so I'll do the switch.
Reply With Quote
  #6  
Old 04-21-2014, 11:12 PM
rojodiablo rojodiablo is offline
Banned
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Sep 2011
Posts: 1,759
Likes: 613
Liked 1,190 Times in 626 Posts
Default

Quote:
Originally Posted by Boondocks View Post
Thanks for letting me know proper position of the firing pin spring! We had it reversed, so I'll do the switch.
Actually, the proper position of the firing pin spring is in a top drawer of your tool box...........

Truly a part added to try and save us from ourselves, and it's not really a worthwhile solution....... I have fired AR based rifles for years and years...... and I have never had a slamfire or a rifle decide to go FA all by itself.
Reply With Quote
The Following 3 Users Like Post:
  #7  
Old 04-21-2014, 11:30 PM
Boondocks Boondocks is offline
Member
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Apr 2014
Posts: 4
Likes: 0
Liked 1 Time in 1 Post
Default

I agree. I'm thinking the spring should find a new home. I don't intend to risk another tied-up bolt.
Reply With Quote
The Following User Likes This Post:
  #8  
Old 01-11-2021, 11:27 AM
rosewood rosewood is offline
Member
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Oct 2019
Location: Georgia
Posts: 2,091
Likes: 4,288
Liked 1,926 Times in 929 Posts
Default

Resurrecting an old thread.

So are the M&P 10s coming with a firing pin spring so that it isn't a floating firing pin?

Have folks removed this spring (effectively converting it to floating) and has there been any issues as a result?

Thanks,

Rosewood
Reply With Quote
  #9  
Old 01-11-2021, 09:44 PM
sgtsandman's Avatar
sgtsandman sgtsandman is offline
US Veteran
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Jan 2014
Location: Aliquippa, PA
Posts: 1,400
Likes: 351
Liked 714 Times in 476 Posts
Default

I think the spring is there to prevent slam fires since the pin is larger than an AR-15 pin. I wouldn't get rid of it.


If you do decide to do it. Test it multiple times at a shooting range to make sure it won't be a problem. Sling shot the action hard. Shoot some test rounds and see if the following shots fire uncommanded. I'm not sure how to do a drop test safely and also not damage the rifle but there is a potential there also.


Again, I wouldn't do it. I figure that spring is there for a reason.
Reply With Quote
The Following 2 Users Like Post:
  #10  
Old 01-12-2021, 12:16 PM
BillyMagg BillyMagg is offline
Member
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Jun 2012
Location: Central Obamastan
Posts: 1,052
Likes: 16,749
Liked 800 Times in 419 Posts
Thumbs down Its a problem

Quote:
Originally Posted by sgtsandman View Post
I think the spring is there to prevent slam fires since the pin is larger than an AR-15 pin. I wouldn't get rid of it.


If you do decide to do it. Test it multiple times at a shooting range to make sure it won't be a problem. Sling shot the action hard. Shoot some test rounds and see if the following shots fire uncommanded. I'm not sure how to do a drop test safely and also not damage the rifle but there is a potential there also.


Again, I wouldn't do it. I figure that spring is there for a reason.
I'm gonna disagree with you one time here Sarge, it tied up the OP's weapon. Eugene Stoner designed the AR-10, he did it right the first time. The OP has demonstrated, that sometimes, safety features added after the fact, do not in fact contribute to overall function or safety of the weapon...

Smith and Wesson has at least one other objectionable such device on their current revolvers...

Don't complicate something simple that works well, and always, always, keep your muzzle pointed in a safe direction!

but I will agree in principle that the original designer know's what he is doing, and I don't like modifying or at home engineering, especially when it has to do with a safety feature, that's why my M&P wears a thumb safety...

Last edited by BillyMagg; 01-12-2021 at 12:19 PM.
Reply With Quote
  #11  
Old 01-12-2021, 01:47 PM
rosewood rosewood is offline
Member
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Oct 2019
Location: Georgia
Posts: 2,091
Likes: 4,288
Liked 1,926 Times in 929 Posts
Default

I would think with the spring in place, then federal primers which are typically not recommended in AR type platforms would be good to go in the M&P10s.
Reply With Quote
  #12  
Old 01-13-2021, 03:04 AM
sgtsandman's Avatar
sgtsandman sgtsandman is offline
US Veteran
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Jan 2014
Location: Aliquippa, PA
Posts: 1,400
Likes: 351
Liked 714 Times in 476 Posts
Default

Quote:
Originally Posted by BillyMagg View Post
I'm gonna disagree with you one time here Sarge, it tied up the OP's weapon. Eugene Stoner designed the AR-10, he did it right the first time. The OP has demonstrated, that sometimes, safety features added after the fact, do not in fact contribute to overall function or safety of the weapon...

Smith and Wesson has at least one other objectionable such device on their current revolvers...

Don't complicate something simple that works well, and always, always, keep your muzzle pointed in a safe direction!

but I will agree in principle that the original designer know's what he is doing, and I don't like modifying or at home engineering, especially when it has to do with a safety feature, that's why my M&P wears a thumb safety...

No problem with the disagreement. That is part of the reason a forum like this exists and while I do have some knowledge on things, I am certainly not the final authority or any kind of credible expert. If you know something I don't, by all means please bring it up. We are all here to learn together.



I did give the option of trying it without the spring as long as they test it first to make sure it won't be a problem.


The OP did bring up the potential issue with Federal primers. Whether any manufacturer uses them or not in .308 ammunition, I can't say. With their reputation of being soft, it could be an issue or it could not.
Reply With Quote
The Following 2 Users Like Post:
  #13  
Old 01-18-2021, 10:46 AM
BillyMagg BillyMagg is offline
Member
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Jun 2012
Location: Central Obamastan
Posts: 1,052
Likes: 16,749
Liked 800 Times in 419 Posts
Cool Yes Sir!

Quote:
Originally Posted by sgtsandman View Post
No problem with the disagreement. That is part of the reason a forum like this exists and while I do have some knowledge on things, I am certainly not the final authority or any kind of credible expert. If you know something I don't, by all means please bring it up. We are all here to learn together.



I did give the option of trying it without the spring as long as they test it first to make sure it won't be a problem.


The OP did bring up the potential issue with Federal primers. Whether any manufacturer uses them or not in .308 ammunition, I can't say. With their reputation of being soft, it could be an issue or it could not.
Thanks Sarge, I do agree with you that it is there for a reason, as I read this again, I wonder if the OP's firing pin spring was assembled with the spring reversed from its intended direction?? it is surprising that it was able to lock up his gun??

We do know that the 6.5 Creedmoor is happier with a smaller diameter firing pin in order to prevent cratered or blown primers. I'm surprised there is enough slop in the OP's bolt to allow the spring to enter the firing pin channel to begin with??
Reply With Quote
  #14  
Old 01-18-2021, 12:10 PM
rosewood rosewood is offline
Member
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Oct 2019
Location: Georgia
Posts: 2,091
Likes: 4,288
Liked 1,926 Times in 929 Posts
Default

Quote:
Originally Posted by BillyMagg View Post
Thanks Sarge, I do agree with you that it is there for a reason, as I read this again, I wonder if the OP's firing pin spring was assembled with the spring reversed from its intended direction?? it is surprising that it was able to lock up his gun??

We do know that the 6.5 Creedmoor is happier with a smaller diameter firing pin in order to prevent cratered or blown primers. I'm surprised there is enough slop in the OP's bolt to allow the spring to enter the firing pin channel to begin with??
Good point. A neighbor took apart his Lorcin .380. Got it jammed up. Took me awhile to get it apart, he installed the firing pin backwards with the firing pin on the wrong side also. After getting it apart and figuring out what he done, realized the firing pin was bent also. After explaining to him what he did, he blamed it on a youtube video. Had him order a new firing pin and also the safety spring he lost somehow.

Some folks just don't need to be taking guns apart.

Rosewood
Reply With Quote
The Following User Likes This Post:
  #15  
Old 01-19-2021, 01:23 AM
sgtsandman's Avatar
sgtsandman sgtsandman is offline
US Veteran
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Jan 2014
Location: Aliquippa, PA
Posts: 1,400
Likes: 351
Liked 714 Times in 476 Posts
Default

Quote:
Originally Posted by BillyMagg View Post
Thanks Sarge, I do agree with you that it is there for a reason, as I read this again, I wonder if the OP's firing pin spring was assembled with the spring reversed from its intended direction?? it is surprising that it was able to lock up his gun??
I don't remember the spring being different on one end compared to the other. It's possible that, that may be the case. I'll have to disassemble my bolt ant take a look at it and the firing pin channel at the back of the bolt carrier to see if that may be the issue,
Reply With Quote
The Following User Likes This Post:
  #16  
Old 01-19-2021, 07:46 AM
rosewood rosewood is offline
Member
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Oct 2019
Location: Georgia
Posts: 2,091
Likes: 4,288
Liked 1,926 Times in 929 Posts
Default

Quote:
Originally Posted by sgtsandman View Post
I don't remember the spring being different on one end compared to the other. It's possible that, that may be the case. I'll have to disassemble my bolt ant take a look at it and the firing pin channel at the back of the bolt carrier to see if that may be the issue,
I haven't taken my apart to see. However, I have seen other guns where the firing pin spring was indeed larger on one end than the other and so subtle you didn't notice unless you tried it both ways.

Interesting...

Rosewood
Reply With Quote
The Following User Likes This Post:
  #17  
Old 01-22-2021, 03:45 AM
sgtsandman's Avatar
sgtsandman sgtsandman is offline
US Veteran
M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue M&P10 firing pin issue  
Join Date: Jan 2014
Location: Aliquippa, PA
Posts: 1,400
Likes: 351
Liked 714 Times in 476 Posts
Default

Quote:
Originally Posted by rosewood View Post
I haven't taken my apart to see. However, I have seen other guns where the firing pin spring was indeed larger on one end than the other and so subtle you didn't notice unless you tried it both ways.

Interesting...

Rosewood
I finally remembered to look. Both ends are the same with the same fit on the firing pin. It locks into a cutout at the base of the pin. The ends taper a bit compared to the middle. I have the original. The Sport model may or ma not be different.
Reply With Quote
The Following User Likes This Post:
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Firing Pin Issue Mike1161 Smith & Wesson M&P Pistols 12 01-22-2015 03:00 AM
Firing pin issue brand new 686 Elmot S&W Revolvers: 1980 to the Present 11 12-07-2014 11:02 AM
M&P 9 Firing issue who-knows-ivix Smith & Wesson M&P Pistols 0 07-09-2013 11:48 AM
40c Firing Issue EXERCISINGTHE2ND Smith & Wesson M&P Pistols 61 01-29-2013 04:36 PM
442 issue.. not firing sbachler S&W Revolvers: 1980 to the Present 16 10-12-2012 01:08 AM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 06:07 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)