|
|
 |
11-26-2012, 10:36 AM
|
 |
Member
|
|
|
Join Date: Nov 2012
Location: S.W. Florida
Posts: 2
Likes: 0
Liked 0 Times in 0 Posts
|
|
Unknown "O" ring appeared while cleaning
Had a great day at the range with my new sport. While cleaning afterwards I found an O ring that may or may not have come out of the bolt carrier group. When I clean, I disassemble the bolt carrier group and let the parts soak in solvent while I clean the barrel. When I went to reassemble I found an o ring that I had not seen before. The inside diameter is the same as the firing pin. Any help would be appreciated.
|
11-26-2012, 10:47 AM
|
 |
Member
|
|
|
Join Date: Sep 2012
Location: Florida
Posts: 62
Likes: 2
Liked 22 Times in 13 Posts
|
|
Here's an exploded view, I don't see an O ring in the BCG?
|
11-26-2012, 10:47 AM
|
 |
Member
|
|
|
Join Date: Nov 2010
Posts: 521
Likes: 225
Liked 364 Times in 184 Posts
|
|
Did you remove the extractor from the bolt? If so it could be the oring from the extractor.
|
|
The Following 2 Users Like Post:
|
|
11-26-2012, 11:04 AM
|
|
Member
|
|
|
Join Date: Oct 2011
Posts: 165
Likes: 2
Liked 49 Times in 37 Posts
|
|
Was just going to suggest the o-ring under the extractor
Sent from my iPhone 4S using Tapatalk
|
11-26-2012, 02:13 PM
|
|
Member
|
|
|
Join Date: Nov 2012
Location: S.W. Florida
Posts: 2
Likes: 0
Liked 0 Times in 0 Posts
|
|
Quote:
Originally Posted by SimpleWeaponSolutions
Did you remove the extractor from the bolt? If so it could be the oring from the extractor.
|
Yes I removed the extractor. It appears from your photo that the o ring goes over the extractor spring. Is that correct?
|
11-26-2012, 02:35 PM
|
 |
Member
|
|
|
Join Date: Feb 2007
Location: Oregon
Posts: 2,403
Likes: 4,558
Liked 2,141 Times in 770 Posts
|
|
Not SWS, but yes, over the extractor spring.
__________________
ΜΟΛΩΝ ΛΑΒΕ
|
11-26-2012, 03:39 PM
|
|
Member
|
|
|
Join Date: Dec 2011
Posts: 895
Likes: 41
Liked 376 Times in 226 Posts
|
|
This raises a good question. Are you guys removing the extractor for cleaning?
|
11-26-2012, 04:05 PM
|
|
Member
|
|
|
Join Date: Oct 2011
Posts: 165
Likes: 2
Liked 49 Times in 37 Posts
|
|
I actually use an ultrasonic bath to clean my bolt.
A little simple green and water, and 1hr in the bath. Take it out, dry it off and oil it up. Works very well. I do it after every session.
Sent from my iPhone 4S using Tapatalk
|
11-26-2012, 04:22 PM
|
|
Member
|
|
|
Join Date: Jan 2012
Location: God's Country
Posts: 4,711
Likes: 1,235
Liked 3,535 Times in 1,770 Posts
|
|
Quote:
Originally Posted by BillyJack2012
This raises a good question. Are you guys removing the extractor for cleaning?
|
And another good question is "Why?"
|
|
Posting Rules
|
|
|
|
|
All times are GMT -4. The time now is 04:37 PM.
Linear Mode
