Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Rifles and Shotguns > Smith & Wesson M&P15 Rifles
o

Notices

Smith & Wesson M&P15 Rifles Dedicated to the Smith & Wesson M&P-15 Rifles


Reply
 
Thread Tools Display Modes
  #1  
Old 09-10-2014, 03:11 PM
harrym harrym is offline
Member
Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque?  
Join Date: Apr 2013
Posts: 169
Likes: 0
Liked 24 Times in 21 Posts
Default Scope ring torque?

When I went to the range today, my AR15's scope was loose in its Burris PEPR mount. I had shot less than 50 rounds since mounting the scope. I noticed that the reticle was off vertical, so that's when I checked it. The only thing besides shooting it that could have changed is replacing the stock handguard with a new MOE-SL handguard. Anyway, it's lined up now and the 12 screws are torqued at 12 pounds. What should the torque be for a scope in this mount? I considered using some blue Loctite, but I'm not sure I'll keep this scope on this rifle.
Reply With Quote
  #2  
Old 09-10-2014, 03:27 PM
cyphertext cyphertext is offline
US Veteran
Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque?  
Join Date: Feb 2012
Location: Wylie, TX
Posts: 4,670
Likes: 1,075
Liked 3,823 Times in 2,040 Posts
Default

Taken from Burris web page...

Scopes - rifle scopes, handgun scopes, hunting scopes by Burris Optics

Q. How do I know how much to tighten my rings and bases?
A. Use the following specifications to correctly tighten your rings and bases. Be careful not to over tighten as doing so can damage your product.

Eliminator / LRFP Base Clamps: 40 inch-pounds
Signature / Zee Ring Tops: 20 inch-pounds
Signature / Zee Base Screws: 30 inch-pounds
Rear Windage Base Screws: 40 inch-pounds
AR-P.E.P.R. /Tactical Ring Tops: 20 inch-pounds
AR-P.E.P.R. /Tactical Ring Crossbolt: 65 inch-pounds

Signature Ring Clamps: 30 inch-pounds
Rimfire / Airgun Rings: 20 inch-pounds
Reply With Quote
  #3  
Old 09-10-2014, 04:18 PM
MichiganScott MichiganScott is offline
Member
Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque?  
Join Date: Jan 2012
Location: God's Country
Posts: 4,711
Likes: 1,235
Liked 3,535 Times in 1,770 Posts
Default

Lock-Tite can make a real mess of the small screws used on the rings. If you really feel that they need help, use some anti-seize compound on the screws. Not only does it make it easier to remove them when you need to, it helps keep them from backing out if torqued to spec.
Reply With Quote
  #4  
Old 09-10-2014, 06:51 PM
78Staff's Avatar
78Staff 78Staff is offline
Member
Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque?  
Join Date: Jan 2014
Location: NE Florida
Posts: 816
Likes: 389
Liked 258 Times in 171 Posts
Default

Echoing what has already been said, different manufacturers require different specs - Larue is 30in-lbs, for instance. 12 is pretty low. Either way, loctite should not be required for ring screws if torque specs and proper tightening procedure is followed.
Reply With Quote
  #5  
Old 09-10-2014, 08:59 PM
harrym harrym is offline
Member
Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque?  
Join Date: Apr 2013
Posts: 169
Likes: 0
Liked 24 Times in 21 Posts
Default

OK, I retightened the ring top screws to 20 pounds. I'll see if they hold at that torque. I had to take a rifle to a gunsmith once to remove a scope base that had been sealed with Loctite, so I want to avoid that. Thanks for the Burris chart.
Reply With Quote
  #6  
Old 09-11-2014, 12:03 AM
Rastoff's Avatar
Rastoff Rastoff is offline
Member
Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque?  
Join Date: Dec 2011
Location: So Cal (Near Edwards AFB)
Posts: 14,710
Likes: 2,926
Liked 17,102 Times in 6,271 Posts
Default

Quote:
Originally Posted by MichiganScott View Post
If you really feel that they need help, use some anti-seize compound on the screws. Not only does it make it easier to remove them when you need to, it helps keep them from backing out if torqued to spec.
Please, please don't do this. The reason they won't back out with this method is that you've greatly over torqued the screws.

Anti-seize is a kind of lubricant. Unless the manufacturer specifically states to use anti-seize, the torque values are for dry screws/bolts.

Torque is a measure of twisting force. The friction created by the increased surface area of a screw is a factor in determining the correct torque value. Because anti-seize reduces the amount of friction, the actual force applied by the screw, when tightened to the recommended torque, is greatly increased.
I have seen wheel lugs snapped off before the recommended torque value was reached because anti-seize was put on the lugs.

So, don't use anti-seize on bolts or screws or nuts when torquing to the manufacturer's spec.


Now, to keep your scope tight, but not over tight, try this....

Mount the scope and go through the pain staking process of getting the reticle level. Then head to the range and fire two shots.
Check the scope ring screws.
Fire 5 shots.
Check the scope ring screws again.
Fire 10 shots.
Check the ring screws again, but they should be good by now.

Doing this helps settle the parts. Any movement that was going to happen, has happened. By doing it incrementally like this, you get it tight before the scope can move out of place. So, do this first, then zero the scope. If you have a quality scope and quality rings, it will stay zeroed for years to come.
__________________
Freedom isn't free.
Reply With Quote
The Following User Likes This Post:
  #7  
Old 09-11-2014, 10:41 AM
MichiganScott MichiganScott is offline
Member
Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque?  
Join Date: Jan 2012
Location: God's Country
Posts: 4,711
Likes: 1,235
Liked 3,535 Times in 1,770 Posts
Default

Quote:
Originally Posted by Rastoff View Post
Please, please don't do this. The reason they won't back out with this method is that you've greatly over torqued the screws.

Anti-seize is a kind of lubricant. Unless the manufacturer specifically states to use anti-seize, the torque values are for dry screws/bolts.

Torque is a measure of twisting force. The friction created by the increased surface area of a screw is a factor in determining the correct torque value. Because anti-seize reduces the amount of friction, the actual force applied by the screw, when tightened to the recommended torque, is greatly increased.
I have seen wheel lugs snapped off before the recommended torque value was reached because anti-seize was put on the lugs.

So, don't use anti-seize on bolts or screws or nuts when torquing to the manufacturer's spec.


Now, to keep your scope tight, but not over tight, try this....

Mount the scope and go through the pain staking process of getting the reticle level. Then head to the range and fire two shots.
Check the scope ring screws.
Fire 5 shots.
Check the scope ring screws again.
Fire 10 shots.
Check the ring screws again, but they should be good by now.

Doing this helps settle the parts. Any movement that was going to happen, has happened. By doing it incrementally like this, you get it tight before the scope can move out of place. So, do this first, then zero the scope. If you have a quality scope and quality rings, it will stay zeroed for years to come.
We will have to agree to disagree on this. Leupold strongly recommends using oil on the screws for their rings and bases. There is a big difference between torquing down a new ring or base screw to 15-65 in-lbs than when torquing a rusted lug bolt to 100+ ft-lbs.

By the way, modern oils creep into just about any place. You will eventually end up with oil on the threads anyway. I've never torqued off a screw head since I started using antiseize, something I can't say for my friends that insist on using Lock-tite.
Reply With Quote
  #8  
Old 09-11-2014, 10:23 PM
Rastoff's Avatar
Rastoff Rastoff is offline
Member
Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque?  
Join Date: Dec 2011
Location: So Cal (Near Edwards AFB)
Posts: 14,710
Likes: 2,926
Liked 17,102 Times in 6,271 Posts
Default

Quote:
Originally Posted by MichiganScott View Post
We will have to agree to disagree on this.
OK.

Quote:
Originally Posted by MichiganScott View Post
Leupold strongly recommends using oil on the screws for their rings and bases.
If the manufacturer recommends it, then they've already taken the added torque into account. So, in that case I'd say it was not only OK, but necessary.
__________________
Freedom isn't free.
Reply With Quote
  #9  
Old 09-12-2014, 02:49 PM
SoCoRuss SoCoRuss is offline
Member
Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque?  
Join Date: Apr 2014
Posts: 71
Likes: 0
Liked 13 Times in 6 Posts
Default

Does the torque recommended have leeway. I have the Leupold Patrol. Guide says 20 inch lbs. I have multiple inch lbs torque wrenches but they all start at 25inch lbs! Not real happy to have to get a new one for 5 inch lbs difference.
Reply With Quote
  #10  
Old 09-12-2014, 03:09 PM
cyphertext cyphertext is offline
US Veteran
Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque?  
Join Date: Feb 2012
Location: Wylie, TX
Posts: 4,670
Likes: 1,075
Liked 3,823 Times in 2,040 Posts
Default

Quote:
Originally Posted by SoCoRuss View Post
Does the torque recommended have leeway. I have the Leupold Patrol. Guide says 20 inch lbs. I have multiple inch lbs torque wrenches but they all start at 25inch lbs! Not real happy to have to get a new one for 5 inch lbs difference.
Leupold says 18 - 22 inch pounds. When I worked at Academy mounting scopes, we didn't have torque wrenches. Got them good and snug and then went about a quarter turn more.

Leupold also recommends lightly lubricating the screws...
Reply With Quote
  #11  
Old 09-12-2014, 07:45 PM
Rastoff's Avatar
Rastoff Rastoff is offline
Member
Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque? Scope ring torque?  
Join Date: Dec 2011
Location: So Cal (Near Edwards AFB)
Posts: 14,710
Likes: 2,926
Liked 17,102 Times in 6,271 Posts
Default

Quote:
Originally Posted by SoCoRuss View Post
Does the torque recommended have leeway. I have the Leupold Patrol. Guide says 20 inch lbs. I have multiple inch lbs torque wrenches but they all start at 25inch lbs! Not real happy to have to get a new one for 5 inch lbs difference.
The best click type torque wrenches on the market have a tolerance of +/-10% which means 22.5-27.5inch/lbs for your wrench. If it hasn't been calibrated in over a year, chances are that tolerance has gone to 20% or worse. That means the torque value could be anywhere from 20-30inch/lbs.

Now, we're talking about inch/lbs here. That's not really a lot of torque. I seriously doubt that you'll damage the rings, screws or scope at that torque.

Just for the record, I have been a Metrologist for about 30 years now. I have calibrated thousands of torque wrenches in that time. The majority of them, that were more than a year old, were either limited to +/-20% or thrown away because they were worse than that.
__________________
Freedom isn't free.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Scope ring Tool Drm50 S&W-Smithing 2 05-03-2015 11:31 PM
Scope Ring Question bodark Smith & Wesson M&P15 Rifles 12 02-15-2015 10:24 AM
SOLD: Wheeler Engineering F.A.T. Scope in/lb Torque Wrench & Crosshair Leveling Kit Thiokol Accessories/Misc - For Sale or Trade 0 12-20-2012 06:35 PM
BSA sweet 22 scope/scope ring questions BIGMAC116 Smith & Wesson M&P 15-22 5 07-22-2011 07:03 PM
Scope Ring Advice Guyman Smith & Wesson M&P 15-22 3 03-09-2010 10:00 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 08:02 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)