|
|
 |
04-01-2020, 09:40 AM
|
|
Member
|
|
|
Join Date: Apr 2020
Posts: 5
Likes: 1
Liked 2 Times in 2 Posts
|
|
M&P Sport 2 Handguard question
Looking to change the hand-guard on the Sport II, the model sport 2 i got came with the red dot so there is no front sight, anyone else swap the front hand-guard out and can post a link to one that will work. also will i need a new gas block?
|
|
The Following User Likes This Post:
|
|
04-01-2020, 09:55 AM
|
 |
US Veteran
|
|
|
Join Date: Feb 2017
Location: Missouri
Posts: 2,929
Likes: 3,902
Liked 6,802 Times in 1,851 Posts
|
|
Is this the style of gas block is has on it?
__________________
SWHF #595
|
04-01-2020, 12:14 PM
|
|
Member
|
|
|
Join Date: Apr 2020
Posts: 5
Likes: 1
Liked 2 Times in 2 Posts
|
|
Yes looks very similar to that one.
|
|
The Following User Likes This Post:
|
|
04-01-2020, 01:04 PM
|
|
US Veteran
|
|
|
Join Date: Feb 2017
Location: Missouri
Posts: 2,929
Likes: 3,902
Liked 6,802 Times in 1,851 Posts
|
|
OK, if your just looking to add iron sights one can be mounted to the rail on the block. If your wanting a free float handguard you'll have to swap the gas block for low profile type.
__________________
SWHF #595
|
04-01-2020, 01:37 PM
|
|
Member
|
|
|
Join Date: Nov 2016
Location: Wisconsin
Posts: 542
Likes: 4
Liked 339 Times in 181 Posts
|
|
I have rhe sport 2 with the A2 site/block.
I was abke to install a magpul SL MLOK hand guard. It wraps around the A2 site and gas block. I guess you could say it mimics a mid length hand guard. It was a bit of a tricky/pain to click into place. But I really like it. And no need to buy and replace the A2 site and gas block.
|
04-01-2020, 02:35 PM
|
|
Member
|
|
|
Join Date: Apr 2020
Posts: 5
Likes: 1
Liked 2 Times in 2 Posts
|
|
I see. i am going for a different look with the hand-guard something with better venting. i also want to be able to put a fore grip attached to the hand-guard and as well as a flip down front sight. What special tools will i need to have?
|
04-01-2020, 08:11 PM
|
|
Member
|
|
|
Join Date: Nov 2016
Location: Wisconsin
Posts: 542
Likes: 4
Liked 339 Times in 181 Posts
|
|
The magpul handguard I mentioned above I believe would do all of those things. It will be able to attach anything that attaches with MLOK fittings.
Magpul makes several different hand grips for it lights lasers etc.
|
04-02-2020, 12:25 PM
|
|
Member
|
|
|
Join Date: Apr 2020
Location: Alabama
Posts: 10
Likes: 5
Liked 2 Times in 2 Posts
|
|
I put a UTG slimline pro carbine length on mine. It’s aluminum, has full length pic rail on top, and m look on the other 3 sides. It’s two piece that bolts together with four screws, it also has two set screws on bottom near delta ring to assure solid install. I really like it.
|
|
The Following User Likes This Post:
|
|
04-02-2020, 01:39 PM
|
|
Member
|
|
|
Join Date: Apr 2020
Posts: 5
Likes: 1
Liked 2 Times in 2 Posts
|
|
I like the way that one looks, did you have to replace the stock gas block on it or take it off at all? as pictured above on this forum.
|
04-02-2020, 01:44 PM
|
|
Member
|
|
|
Join Date: Apr 2020
Posts: 5
Likes: 1
Liked 2 Times in 2 Posts
|
|
Can you post a picture of the UTG slimline pro on your AR? Thanks
|
04-02-2020, 03:46 PM
|
|
Member
|
|
|
Join Date: Apr 2020
Location: Alabama
Posts: 10
Likes: 5
Liked 2 Times in 2 Posts
|
|
DBrownn33. No, I didn’t have to replace or change anything else. Strait off with the stock one and on with the UTG slimline. UTG has a flange where the two pieces overlap and then bolt together. I also added a Magpul angled fore end on mine. I’ll post pic too.
The close up pic shows the two bolts that hold the two pieces together. There are two bolts on the opposite side also. And two set screws that are on the bottom side. Very solid.
__________________
Aim small, squeeze often!
|
|
Posting Rules
|
|
|
|
|
All times are GMT -4. The time now is 10:35 AM.
Linear Mode
