Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Semi-Automatic Pistols > Smith & Wesson SD & Sigma Pistols
o

Notices

Smith & Wesson SD & Sigma Pistols SD & Sigma Pistols in All Generations


Reply
 
Thread Tools Display Modes
  #1  
Old 03-26-2017, 08:01 AM
Gsx4's Avatar
Gsx4 Gsx4 is offline
Member
Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience  
Join Date: Mar 2017
Posts: 26
Likes: 7
Liked 32 Times in 13 Posts
Default Apex Trigger Install - My Experience

I found myself with some unexpected free time yesterday afternoon. So, what does one do when you have free time? You install the Apex trigger and spring kit, and extended slide release takedown plate into your SD9.
For self-education purposes I watched Apex’s tutorial video and also Sootch00’s on YouTube. Sootch’s is an HD version based on Apex’s, which is SD.
Installing the two springs in the slide took about 10 minutes. Changing out the trigger and trigger return spring, and take down plate took about another 20 – 30 minutes. Everything went smoothly according to the aforementioned tutorial videos. The only problem I had was the trigger pin that holds the locking block, return spring and slide release. The slide release spring was getting stuck between the frame and the slide release arm preventing the spring from locking into the trigger pin. When looking at it, it looked good, but the pin would not “click” into place. Once I noticed my error it clicked right in. Yay!
Function testing showed that my work was good. As instructed by Apex, I could see the sear properly engaged with the trigger bar. I also pressed down on the release tab several times as recommended. All looked good.I reassembled the pistol and dry fired several times pulling the trigger normally. I thought I would be one of the lucky ones and not have to file the back of the trigger for added relief. That was until I pulled the trigger slowly. It didn’t work every time. No good.
After double checking my work on the inside, I started filing the area on the back of the trigger, as instructed by Apex, using the small files I have for guitar work. As Apex recommended, small amounts at a time. I decided 10 strokes at a time (one down/up motion = one stroke). After each one of these processes I would check the trigger. No improvement. In fact after four or five of the filing processes it seemed to be getting worse, not better. Checked my work on the inside again. All seemed good. More filing. Apex said you may have to remove .015 to .020. Seemed like a lot to me, but I took their word and kept at it. After more filing the dry firing was definitely getting worse. I was not happy, but noticed when I pulled the trigger with my left trigger finger, which exerted a little pressure to the right the gun would fire fairly consistently. And even though I had at this point checked my work several times, I could feel in the trigger pull something akin to two smooth parts rubbing against each other, which I hadn’t noticed before. I initially attributed this to the new springs/trigger, but took the slide off one more time just to be sure. Slow trigger pulls watching the mechanism. Good. Hit the release tab several times again. Good. Looked for any foreign objects that may have found their way inside. Nothing. Turned the frame upside down and tapped it against my hand. Nothing. Inspected the function again. Looked good. Put the gun back together. Slowly pulled the trigger. Click. At this point I’m pretty sure I could hear the Hallelujah Chorus going on in the background. The trigger pull felt smooth. It reset perfectly. In fact it reset perfectly another fifty or so times. I don’t know what I did, but the rubbing feeling I felt earlier was gone. The trigger pull was smooth and consistent. Mr. Lyman showed an average pull weight of 5-3/4 lbs. This down from the stock weight of 8-1/2 to 9 lbs. Take up was a little shorter. Reset slightly shorter. Emphasis on slightly. Was it worth the time and investment? Yes. The trigger is much better than stock. I estimate I had to file off about .010 to .012 off the specific part of the back of the trigger before finding the sweet spot, which admittedly was a frustrating process. I hope to get to the range tomorrow to live fire test this new setup. I’ll post an update after that.
__________________
Gsx4
Reply With Quote
The Following 2 Users Like Post:
  #2  
Old 03-26-2017, 07:38 PM
mlk18's Avatar
mlk18 mlk18 is offline
Member
Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience  
Join Date: May 2005
Location: U.S.A.
Posts: 2,426
Likes: 296
Liked 785 Times in 356 Posts
Default

Interesting. I have installed 5-6 Apex kits/triggers in SD9's and have yet to need to modify them at all. Just plug and play. Hope it shoots well for you.
Reply With Quote
  #3  
Old 03-26-2017, 07:51 PM
Gsx4's Avatar
Gsx4 Gsx4 is offline
Member
Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience  
Join Date: Mar 2017
Posts: 26
Likes: 7
Liked 32 Times in 13 Posts
Default

Thanks mlk18. Since I don't know what caused the trigger to function normally after filings and several re-inspections, I can't be certain the filing was necessary. It could have been another problem unrelated to the trigger relief. What that problem might have been though is a mystery and frustrating for the owner.
__________________
Gsx4
Reply With Quote
  #4  
Old 03-27-2017, 01:30 AM
Disabled1 Disabled1 is offline
Banned
Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience  
Join Date: Apr 2015
Location: South Of The North Pole
Posts: 1,257
Likes: 491
Liked 710 Times in 424 Posts
Thumbs up

Quote:
Originally Posted by mlk18 View Post
Interesting. I have installed 5-6 Apex kits/triggers in SD9's and have yet to need to modify them at all. Just plug and play. Hope it shoots well for you.
Same here. I have (4) APEX trigger and spring installs on my other (4) fantastic plastic S&W's (SW9VE, SW40VE, SD9VE, SD40VE). Those triggers average out to 5.5-5.75 lbs.
Reply With Quote
  #5  
Old 03-27-2017, 09:20 AM
NevadaBob's Avatar
NevadaBob NevadaBob is offline
Member
Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience  
Join Date: Apr 2012
Location: Reno, NV
Posts: 421
Likes: 563
Liked 206 Times in 130 Posts
Default

Thanks Gsx4 for taking the time to post your experience. It is helpful to everyone! I did likewise back in '13. There are some tweaks/quirks in the install process that the Apex folks don't address. If one were to use the search function, put in the word "rocket" in the "SD & Sigma" subforum, my thread can be located.
Reply With Quote
The Following User Likes This Post:
  #6  
Old 03-28-2017, 12:35 PM
rwj56 rwj56 is offline
Member
Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience Apex Trigger Install - My Experience  
Join Date: Apr 2016
Posts: 80
Likes: 4
Liked 24 Times in 16 Posts
Default

Thanx Gsx4 for that post I ordered the trigger and spring kit for my newly aquired SD9ve Yesterday hopefully mine will go smooth ,I have installed the apex trig/spring kit in my M&P9c but that is a totally different animal,that install went very smooth.
Reply With Quote
The Following User Likes This Post:
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
What trigger pull weight are you getting on your APEX Flat Faced FSS Trigger install? falconman515 Smith & Wesson M&P Pistols 42 12-17-2021 11:20 PM
Help with Apex trigger install please chele519 Smith & Wesson M&P Pistols 20 10-30-2015 10:47 PM
Need help about apex trigger install ussoldier1984 Smith & Wesson M&P Pistols 31 05-30-2015 04:44 PM
Trigger pre-travel in Shield after Apex trigger install MKE.guns Smith & Wesson M&P Pistols 4 03-13-2015 03:22 PM
Need immediate APEX trigger install help!! zgoettsc Smith & Wesson M&P Pistols 18 03-03-2014 10:11 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 02:40 PM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)