Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Semi-Automatic Pistols > Smith & Wesson Semi-Auto Pistols
o

Notices

Smith & Wesson Semi-Auto Pistols Other Smith & Wesson Semi-Automatic Pistols from the 1950's to Present


Reply
 
Thread Tools Display Modes
  #1  
Old 11-01-2020, 07:55 PM
jdlii's Avatar
jdlii jdlii is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Jun 2009
Location: TN
Posts: 2,222
Likes: 5,163
Liked 4,852 Times in 1,390 Posts
Default 39-2 Takedown Issues

I acquired a very nice Mod. 39-2 last month, 98% with the box and documents. Took it apart for inspection and cleaning with no issues.

Today, for the first time, I got a chance to shoot it and see how it performed. Got home and prepared to take it down for cleaning.

Took a look at the youtube video again for a refresher course. Pulled the slide back, lined up the slot in the slide with the take down pin. Couldn't push it out without the use of the plastic handle of a gun cleaning tooth brush.

Got the pin out but, can't get the slide to separate from the frame by sliding it forward. It moves about an inch and locks up. Put the take down pin/lever back in and it functions fine.

WHAT THE HECK AM I DOING WRONG?

Thank you in advance for your answers and assistance!

Frustrated in TN!

Last edited by jdlii; 11-26-2020 at 11:15 AM.
Reply With Quote
  #2  
Old 11-01-2020, 08:13 PM
Heymatt Heymatt is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Jan 2019
Location: SE Fla
Posts: 819
Likes: 876
Liked 1,360 Times in 504 Posts
Default

Silly question, did you remove the magazine?
Reply With Quote
The Following User Likes This Post:
  #3  
Old 11-01-2020, 08:14 PM
jdlii's Avatar
jdlii jdlii is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Jun 2009
Location: TN
Posts: 2,222
Likes: 5,163
Liked 4,852 Times in 1,390 Posts
Default

Yes, I removed the magazine.
Reply With Quote
  #4  
Old 11-01-2020, 08:20 PM
S&WIowegan S&WIowegan is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: May 2004
Location: Iowa
Posts: 4,106
Likes: 14,444
Liked 3,763 Times in 1,784 Posts
Question

Is the gun cocked?
__________________
Bob.
SWCA 1821
Reply With Quote
  #5  
Old 11-01-2020, 08:27 PM
jdlii's Avatar
jdlii jdlii is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Jun 2009
Location: TN
Posts: 2,222
Likes: 5,163
Liked 4,852 Times in 1,390 Posts
Default

Yes, the hammer is cocked. As I am sure you know, when you move the slide to the rear, to line up the cut out in the slide to the take down pin/lever, the hammer is cocked.

Last edited by jdlii; 11-01-2020 at 09:02 PM.
Reply With Quote
  #6  
Old 11-01-2020, 08:49 PM
Sevens Sevens is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Mar 2015
Location: Ohio
Posts: 7,827
Likes: 9,401
Liked 14,752 Times in 5,026 Posts
Default

Often the recoil guide rod will get ever so slightly out of place and it makes it difficult to remove. When this happens, I draw the slide back as far as I am able and then I get a hold of the muzzle end of the guide rod as it protrudes from the slide. Pull it — try to seat it properly, let it go carefully and then again attempt to move the slide forward and off the frame, taking care to help the hammer fall gently and not smack the frame.

It’s a little difficult to put this in to words but it isn’t difficult to attempt this.
Reply With Quote
The Following User Likes This Post:
  #7  
Old 11-01-2020, 11:18 PM
Pine_Worker's Avatar
Pine_Worker Pine_Worker is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Oct 2007
Location: Central Texas
Posts: 1,489
Likes: 2,637
Liked 1,588 Times in 713 Posts
Default

[QUOTE .......taking care to help the hammer fall gently and not smack the frame.

[/QUOTE]

Yes, the hammer must be forward for the slide to be removed. If it does not automatically fall forward, the trigger must be pulled.
__________________
Pine_Worker
Ex-LEO, NRA Life
Reply With Quote
The Following User Likes This Post:
  #8  
Old 11-02-2020, 01:50 AM
Sevens Sevens is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Mar 2015
Location: Ohio
Posts: 7,827
Likes: 9,401
Liked 14,752 Times in 5,026 Posts
Default

It will absolutely “fall forward” unless your decock linkage is broken, the slide rides over the finger that makes the hammer drop as you move the slide forward off your frame.
Reply With Quote
  #9  
Old 11-07-2020, 01:58 PM
jdlii's Avatar
jdlii jdlii is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Jun 2009
Location: TN
Posts: 2,222
Likes: 5,163
Liked 4,852 Times in 1,390 Posts
Default

Nope, it is still a "no go." I can remove the pin but, the slide will move forward about 1/4" and no more.

I have pulled the slide to the rear, as far as possible, and tried to wiggle and/or move the rod guide. It will not budge and I am sure not going to force it.

Any suggestions?

Thanks!
Reply With Quote
  #10  
Old 11-07-2020, 03:14 PM
gmborkovic gmborkovic is online now
SWCA Member
39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Feb 2014
Location: VA & SoFL
Posts: 8,644
Likes: 469
Liked 5,697 Times in 3,186 Posts
Default

Up for discussion:
1. remove mag.
2. remove hammer and spring
3. remove grips, for a better view.
__________________
Mike 2796
SoFo Bunch member
Reply With Quote
  #11  
Old 11-07-2020, 03:59 PM
Sevens Sevens is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Mar 2015
Location: Ohio
Posts: 7,827
Likes: 9,401
Liked 14,752 Times in 5,026 Posts
Default

I have only two suggestions. I see that you did attempt what I suggested, I will suggest it again, in a slightly different way. (Not that you didn't try, merely saying that if we were in the same room, it is the first thing I would try! )

Slide stop still in place, magazine out, pistol functional--

Draw slide all the way back and with a thin rubber grabbing assistance (think rubber kitchen jar opener, a short bit of bicycle tire innertube, ANYTHING that enhances your grip but certainly not a pair of pliers) try again to get a hold of the guide rod from the muzzle end and slowly rotate it a few degrees or slowly and carefully, a full 360 degrees, plus or minus.

Basically, anything so that the guide rod ends up somewhere other than it's orientation for the last 20 years.

Then again attempt to remove the slide stop and move the slide forward slowly off the frame. Must know: the hammer absolutely has to be cocked fully (not half cock) if you want to draw the slide off the frame on a 39-2. This is because the sear release lever will not allow the slide to go forward unless it is able to fall. At hammer half-cock, that sear release lever will not go down in to the frame and allow the slide to pass over it.

If the sear release lever cannot lower in to the frame, the slide isn't coming off the frame.

Edit to add!
I just did this repeatedly on my 39-2 and I am going to say it is quite possible that all you are missing here is that you need to start with the hammer fully cocked. Once the slide moves forward enough, it will drop the hammer for you -- be ready to catch it.
Reply With Quote
The Following User Likes This Post:
  #12  
Old 11-10-2020, 10:34 PM
jdlii's Avatar
jdlii jdlii is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Jun 2009
Location: TN
Posts: 2,222
Likes: 5,163
Liked 4,852 Times in 1,390 Posts
Default

It is now in the hands of my trusted gunsmith. Moving and/or rotating the recoil rod did not have the desired effect. I was able to completely rotate the recoil rod and even pull it slightly forward, in hope of getting it back in its proper position. That simply didn't work.

I am hopeful that my GS will be able to get the pistol apart and back together properly. If not, it may have to be returned to the mothership.

Last edited by jdlii; 11-12-2020 at 10:53 PM.
Reply With Quote
The Following User Likes This Post:
  #13  
Old 11-12-2020, 10:47 PM
peterdeb's Avatar
peterdeb peterdeb is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Sep 2013
Location: The FREE state of Florida
Posts: 590
Likes: 978
Liked 527 Times in 268 Posts
Default

Owning a couple of these, I am sure interested in what the GS says was the problem. Please keep us updated.
Reply With Quote
The Following User Likes This Post:
  #14  
Old 11-21-2020, 02:31 PM
jdlii's Avatar
jdlii jdlii is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Jun 2009
Location: TN
Posts: 2,222
Likes: 5,163
Liked 4,852 Times in 1,390 Posts
Default

My GS got it apart and diagnosed the problem as a burr on the ejector. Apparently the burr was not allowing the slide to move completely forward.
He is going to "polish" the burr down and hopefully this this resolve the issue.

The root cause, according to our conversation, is most likely the Winchester steel cased "Range" ammunition that I shot the first and only time I fired the Mod. 39. The pistol definitely doesn't like this ammo and out of the 25 rounds that I fired, it failed to extract and eject over 30% of the time. No more steel ammo of any kind for this pistol and believe it or not, I bought this ammo to shoot in a CZ Mod. 75 that I sold. Otherwise my practice is never to shoot steel cased ammo in any firearm that I own.

Live and learn.
Reply With Quote
The Following 2 Users Like Post:
  #15  
Old 11-21-2020, 03:19 PM
Green Frog Green Frog is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Jul 2010
Location: Central VA
Posts: 8,598
Likes: 1,551
Liked 9,325 Times in 4,182 Posts
Default

Quote:
Originally Posted by jdlii View Post
My GS got it apart and diagnosed the problem as a burr on the ejector. Apparently the burr was not allowing the slide to move completely forward.
He is going to "polish" the burr down and hopefully this this resolve the issue.

The root cause, according to our conversation, is most likely the Winchester steel cased "Range" ammunition that I shot the first and only time I fired the Mod. 39. The pistol definitely doesn't like this ammo and out of the 25 rounds that I fired, it failed to extract and eject over 30% of the time. No more steel ammo of any kind for this pistol and believe it or not, I bought this ammo to shoot in a CZ Mod. 75 that I sold. Otherwise my practice is never to shoot steel cased ammo in any firearm that I own.

Live and learn.
Your Model 39-2 is a thoroughbred. You don’t get Kentucky Derby performance feeding your thoroughbred crabgrass. Just sayin’.

Froggie
Reply With Quote
The Following 2 Users Like Post:
  #16  
Old 11-21-2020, 07:11 PM
gmborkovic gmborkovic is online now
SWCA Member
39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Feb 2014
Location: VA & SoFL
Posts: 8,644
Likes: 469
Liked 5,697 Times in 3,186 Posts
Default

Mr. j, glad you got it resolved with no damage. Maybe just a little tap on the back of the slide. And free. Lesson about steel cases.
__________________
Mike 2796
SoFo Bunch member
Reply With Quote
  #17  
Old 11-21-2020, 08:38 PM
Sistema1927's Avatar
Sistema1927 Sistema1927 is offline
US Veteran
39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Dec 2003
Location: "Land of Disenchantment"
Posts: 3,375
Likes: 3,918
Liked 9,077 Times in 2,497 Posts
Default

Funny how the human mind works. When I saw the title, I only saw "39" and Takedown".

I opened this thread thinking that it was going to be about a certain Marlin .22 levergun.
__________________
Only a cold warrior
Reply With Quote
  #18  
Old 11-21-2020, 09:11 PM
stansdds stansdds is offline
Member
39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues 39-2 Takedown Issues  
Join Date: Apr 2007
Location: Virginia
Posts: 8,717
Likes: 19,291
Liked 11,744 Times in 5,354 Posts
Default

Quote:
Originally Posted by jdlii View Post
My GS got it apart and diagnosed the problem as a burr on the ejector. Apparently the burr was not allowing the slide to move completely forward.
He is going to "polish" the burr down and hopefully this this resolve the issue.

The root cause, according to our conversation, is most likely the Winchester steel cased "Range" ammunition that I shot the first and only time I fired the Mod. 39. The pistol definitely doesn't like this ammo and out of the 25 rounds that I fired, it failed to extract and eject over 30% of the time. No more steel ammo of any kind for this pistol and believe it or not, I bought this ammo to shoot in a CZ Mod. 75 that I sold. Otherwise my practice is never to shoot steel cased ammo in any firearm that I own.

Live and learn.
Reason number 398 for me not using steel cased ammo in my U.S. made firearms.
__________________
VCDL, GOA, NRA
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Takedown Pin foxchase Smith & Wesson M&P 15-22 23 03-21-2014 12:37 PM
Firing pin issues? / wear issues christopher002600 Smith & Wesson M&P Pistols 21 07-06-2013 11:19 AM
Takedown pin okstcowboy Smith & Wesson M&P 15-22 16 03-03-2011 08:43 AM
Bodyguard Takedown issues bodyguard32411 Smith & Wesson Semi-Auto Pistols 6 01-23-2011 01:10 AM
M&P 9 takedown calward Smith & Wesson M&P Pistols 17 01-15-2011 04:48 AM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 11:39 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)