Recent content by datsun40146

  1. datsun40146

    TITANIUM CYLINDERS ON THE 432UC & 632UC

    My S&W 432UC came back from S&W two weeks ago. The titanium cylinder was installed, total cost was about $167 and 7 weeks turn around or so. The original cylinder and ratchet were returned. The teeth on the new cylinder were different than the original one giving a little different trigger...
  2. datsun40146

    TITANIUM CYLINDERS ON THE 432UC & 632UC

    Cylinder only, reuse existing crane. Return steel cylinder
  3. datsun40146

    TITANIUM CYLINDERS ON THE 432UC & 632UC

    Just paid s&w, will be several weeks yet. Was 165 round trip with the work and shipping.
  4. datsun40146

    432UC Ti (Titanium) - A Cautionary Tale re: Ammo Pressure

    Do not, polish the cylinders of your Smith & Wesson titanium cylinders in that method. They are coated specifically and you will remove that coating.
  5. datsun40146

    TITANIUM CYLINDERS ON THE 432UC & 632UC

    About 250 all said and done
  6. datsun40146

    TITANIUM CYLINDERS ON THE 432UC & 632UC

    Just sent my 432UC back to smith to have the Ti cylinder fitted. Should be done in 4 weeks. They wouldn’t sell it separately
  7. datsun40146

    **SOLD** S&W 432PD

    Sold: Pending funds to S&W member Lewel Up for sale is a s&w 432 PD. Chambered in .32 H&R magnum. I’ve run magnums, longs and shorts through the revolver, all shot well. The s&w shorts feel like a cap gun, really very enjoyable. Comes with the original S&w blue box, paperwork etc. I think I...
  8. datsun40146

    .38 Special Starline or Horandy Brass

    Looking for 300 or so .38 special brass. The headstamps must be either hornandy or starline matching across the brass. I can buy it new for around .20 each so was hoping someone had some used brass before I purchased new. Message me if you have some to be rid of.
  9. datsun40146

    Moon Clip Conversion Issues

    Yes I can fire the rounds without issue when the moonclip isn’t used. I just did this. The clips wouldn’t load smoothly so I unloaded them from the clip, manually loaded and fired without issue
  10. datsun40146

    Moon Clip Conversion Issues

    Good question, the resizing die is the Lee 4 die set in my 550b. It’s set to touch off the shell plate and then 1/4 turn more so the handle cams over. That should be correct. That’s the way I’ve done it for the last 20k rounds or so anyway. As far as going thinner on the clips. I’m already at...
  11. datsun40146

    Moon Clip Conversion Issues

    Note: The ammunition is hanging up in the cylinder in the attached pictures, I could force the rounds down, but it takes a bit of force to get them to seat enough that it would hurt my thumb after a while, and they do not eject freely either
  12. datsun40146

    Moon Clip Conversion Issues

    IMG-9058 hosted at ImgBB — ImgBB IMG-9055 hosted at ImgBB — ImgBB IMG-9054 hosted at ImgBB — ImgBB Images of the loading issue
  13. datsun40146

    Moon Clip Conversion Issues

    Good Afternoon Everyone, I had a pre-10 cylinder converted to moon clips recently. I’m having an issue with some of my ammunition that I’ve reloaded not seating all the way into the cylinder. I understand moon clips may be sensitive to brass brands but i’m seeing inconsistent issues across...
  14. datsun40146

    2” 5-Screw .38 Special BNP Stamp “C-Prefix”

    Ordered a pre-10 cylinder with crane and extractor in .38 special. Will attempt to fit just the cylinder using the extractor etc from the current setup. Will see how it fits. I can do some minor hand fitting as needed
  15. datsun40146

    2” 5-Screw .38 Special BNP Stamp “C-Prefix”

    Barrel is 2” it’s original, we’ve decided that the cylinder was replaced. Frame and barrel are original pre-10 M&P. Also I had some .38 s&w cases around. Setup the press, loaded up a few and they chamber, so does .38 special. Confirmed. Pre-10 .38 special with .38 s&w cylinder from a British...
Back
Top