|
|
10-15-2013, 09:19 PM
|
|
Member
|
|
|
Join Date: Oct 2013
Location: Oklahoma
Posts: 1,301
Likes: 1,589
Liked 10,390 Times in 1,029 Posts
|
|
Can I load a 9mm bullet in a .38 Special case?
I don’t know if this is wise or if it will work but I’ll ask all the same before I load any.
I have a couple of boxes of 124GR 9mm plated bullets but don’t own a 9mm pistol. A .38 Special bullet measures .357 and the 9mm is .355. Because the 9’s don’t have a cannula they will need to be taper crimped in the .38 case. With a good crimp I think they will be OK in my old M&P revolver.
Can this be done and still have a reasonably accurate round or am I missing something?
Thanks
|
10-15-2013, 09:23 PM
|
|
US Veteran
|
|
|
Join Date: Mar 2001
Location: illinois
Posts: 6,299
Likes: 1,851
Liked 6,696 Times in 2,119 Posts
|
|
Yes, it will work.
|
10-15-2013, 09:25 PM
|
Member
|
|
|
Join Date: Apr 2007
Location: NW Indiana
Posts: 525
Likes: 1
Liked 36 Times in 16 Posts
|
|
9mm in 38 brass
I never loaded FMJ bullets, but when we had Python BBLs installed on/in our SW's we shot 9mm LRN all the time. Colt bbl inside diameter is , if I remember about 355/356. They worked great, mostly for cardboard/plates. I do not remember load, but Hodgdon's web site might have loading for light 38 bullets. Good luck
|
10-15-2013, 09:28 PM
|
|
SWCA Member
|
|
|
Join Date: Jan 2006
Location: Texas
Posts: 3,352
Likes: 10,450
Liked 6,095 Times in 1,249 Posts
|
|
Sure can. Works well in a pinch and even groups fairly accurately at reasonable handgun ranges. Lead or jacketed. Use .38 Special loading data appropriate for the bullet weight selected.
|
10-15-2013, 09:28 PM
|
Member
|
|
|
Join Date: Jan 2008
Location: Harlem, Ohio
Posts: 14,463
Likes: 23,535
Liked 26,396 Times in 9,153 Posts
|
|
I had a 124 gr. RN 9mm bullet mould and loaded about 15 or 20 thousand 9mm's with it but loaded 25 or 30 thousand 38 specials with the same bullet and they shot better than I do. Ivan
|
10-15-2013, 09:56 PM
|
Member
|
|
|
Join Date: Nov 2008
Posts: 137
Likes: 0
Liked 44 Times in 28 Posts
|
|
yes you can. i have use 9 mm bullets in 38 special loads many times.
|
10-16-2013, 06:06 AM
|
|
Member
|
|
|
Join Date: Aug 2010
Location: C-Bus
Posts: 6,335
Likes: 4,311
Liked 4,916 Times in 2,086 Posts
|
|
You may want to check the cylinder after firing a round or two to make sure of your crimp. You don't want to risk "pushing back" the remaining bullets into their cases.
|
10-16-2013, 08:28 AM
|
|
Member
|
|
|
Join Date: Oct 2010
Location: Fort Worth
Posts: 478
Likes: 118
Liked 106 Times in 70 Posts
|
|
I would definitely check them out after loading just a few. My 38 Super dies (three different sets from two brands) will NOT size the brass down enough to retain a .355 jacketed bullet. I found out when measuring the OAL with the calipers. Turning the wheel pushed the bullet down into the case.
|
The Following 2 Users Like Post:
|
|
10-16-2013, 10:21 AM
|
|
Member
|
|
|
Join Date: Apr 2006
Posts: 17,832
Likes: 7,857
Liked 25,761 Times in 8,708 Posts
|
|
Just as a note ----- while they may work, with fixed sight guns they will probably shoot low.
|
10-16-2013, 11:30 AM
|
Member
|
|
|
Join Date: Jul 2004
Location: Michigan\'s Upper Peninsu
Posts: 3,337
Likes: 207
Liked 1,644 Times in 756 Posts
|
|
I shot 125 grain lead truncated cone 9mm bullets out of my Ruger Blackhawk
.357 for a while. Loaded them in .38 Special cases with a target
level load of Bullseye and CCI primers.
Shot to point of aim in the Blackhawk and made good groups at
20 yards, or so.
Only switched to 158 grain LSWCs after the gunstore ran out of the
9mm TCs.
|
10-16-2013, 11:51 AM
|
Member
|
|
|
Join Date: Nov 2006
Location: Montana
Posts: 5,164
Likes: 3,441
Liked 6,258 Times in 2,063 Posts
|
|
I load 147 and 125 Truncated cone lead 9mm projectiles in 38 special casings all the time for my rifles in SASS.....they feed SO well and at the distances we shoot at are plenty accurate.
Randy
|
10-16-2013, 12:28 PM
|
|
Member
|
|
|
Join Date: Jan 2008
Location: central ohio
Posts: 1,385
Likes: 949
Liked 826 Times in 488 Posts
|
|
Groo here
That was an old trick when there was jacketed 9mm bullets but no light
38's.
The best luck was with the Colt Python barrel as they started out
in the 357/358 size then choked down to 356/354 range,
Better for accurate shooting but the tight bore was slower than S&W.
|
10-16-2013, 12:53 PM
|
|
Member
|
|
|
Join Date: Sep 2012
Location: western Washington
Posts: 2,647
Likes: 1
Liked 763 Times in 454 Posts
|
|
I had the same idea, to try some 115 gr 9mm JHP's in my Chief Special. The .355" bullets seemed too loose a fit in the cases for my taste.
|
10-16-2013, 12:55 PM
|
|
Member
|
|
|
Join Date: Sep 2012
Location: western Washington
Posts: 2,647
Likes: 1
Liked 763 Times in 454 Posts
|
|
Quote:
Originally Posted by blujax01
You may want to check the cylinder after firing a round or two to make sure of your crimp. You don't want to risk "pushing back" the remaining bullets into their cases.
|
You would be in danger of "push back" with a semi-auto, with a revolver having an undersized bullet "jump the crimp" is the concern.
|
The Following 3 Users Like Post:
|
|
10-16-2013, 05:53 PM
|
|
Member
|
|
|
Join Date: Aug 2010
Location: C-Bus
Posts: 6,335
Likes: 4,311
Liked 4,916 Times in 2,086 Posts
|
|
Quote:
Originally Posted by hotrod150
You would be in danger of "push back" with a semi-auto, with a revolver having an undersized bullet "jump the crimp" is the concern.
|
Yeah, that
Thanks.
|
|
Posting Rules
|
|
|
|
|