Pocket reamer for 5.56 brass ?

ericflanders@sbcglobal.ne

[email protected]

Member
Joined
May 22, 2015
Messages
40
Reaction score
9
Location
Akron, Ohio
I used my Lyman pocket reamer by hand and did not remove much material, also had issues with a half a dozen primers not fitting in the pocket. Yesterday I stuck the reamer in a drill and was shocked at how much material it removed, is a reamer designed to run all the way in and the resulting bevele in the pocket is ok? Seems like it removed quite a bit of material.
 

Attachments

  • Reamed Primer Pocket.jpg
    Reamed Primer Pocket.jpg
    32.8 KB · Views: 155
Register to hide this ad
Cdog said:
I've tried several tools and methods. If I'm going to do it, this is the best tool I've used for the job . . . the RCBS Bench Mounted Primer Pocket Swager
Click to expand...

I don't have experience with 5.56 brass but discovered Federal .223 brass has staked primers that require preparation before inserting new primers.

An RCBS swager did the majority of the primer pocket prep without cutting away excessive material . . . but I also found it helpful to use a reamer to finish the job.

Russ
 
I use a RCBS press mounted swager. It's tedious, but cheap, and you're only doing it once anyway.

I'd throw the Lyman reamer in the trash. You no longer have a primer pocket. What you now have is a brass funnel. I can't imagine that anything good will happen if you continue using it. I'd be concerned that the primers would rivet and blow out damaging the bolt face.
 
MichiganScott said:
I use a RCBS press mounted swager. It's tedious, but cheap, and you're only doing it once anyway.

I'd throw the Lyman reamer in the trash. You no longer have a primer pocket. What you now have is a brass funnel. I can't imagine that anything good will happen if you continue using it. I'd be concerned that the primers would rivet and blow out damaging the bolt face.
Click to expand...

I have used a Lyman reamer forever........You statement is unfounded and untrue.
 
I use a Dillon Super Swager (bench mount) for military brass. In fact, most commercial brass crimp the primers in place, just to less extremes.

A swager is fast, and doesn't remove material. If the pocket doesn't need swaging, or has already been swaged, the tool operates without resistance and does no harm. Each time you use a reamer, some material is removed whether it needs it or not.

Military brass usually needs trimming too. Once that's done, you can reload several times before it's out of spec again.
 
The Dillon Swager has been one of the most efficient tools ever for the job. Best money I ever spent!
I've done thousands upon thousands of crimped casings in both small and large primer.
Randy
 
Most of the shall primer pocket reamers are intended for uniforming the pockets, not crimp or stake removal. People did that because it was a tool they had and it works... sometimes.

I have the RCBS pocket swaging tool because Dillon hadn't invented theirs yet when I needed one in the late 70's.

Ivan
 
For me the least effective method is the RCBS die type press mounted system. A total waste of effort.

Many years back I'd quit fooling with anything with crimped pockets. If not for bench tools like the RCBS and Dillon products, I still wouldn't fool with it.
 
MichiganScott said:
Yes, but do you stop when the crimp is removed or do you continue to cut away half the head on a 5.56 case like the OP apparently has done?
Click to expand...

I also agree, never had an issue with the Lyman. I just knock off the crimp and the primers fit like a glove. I could see where if you had it on a drill and pressed too hard you WILL get a loose primer pocket. FWIW I use it on my drill on HIGH speed and never had an issue yet. just needs a touch.
 
I've used the RCBS Military Crimp Remover and it works well. Yes, it is a reamer but the way it's made I don't see how anyone could screw it up no matter how stupid they are.:eek: Fact is it will only go so deep no matter how hard you try to jam it in there. So far mine has removed the crimp from over 2k 5.56 cases without a single issue and it's quick too. I use it on my cordless drill.

044-90386.jpg
 
jwalts27 said:
I also agree, never had an issue with the Lyman. I just knock off the crimp and the primers fit like a glove. I could see where if you had it on a drill and pressed too hard you WILL get a loose primer pocket. FWIW I use it on my drill on HIGH speed and never had an issue yet. just needs a touch.
Click to expand...

Apparently MC has never used one.....Finese(sp?) is required with all tools.
 
I use the Lyman by hand mostly. I have used it with a drill when I did a big run of cases. True that the drill method will remove more material. I just take it easy. No problem. Never had any problems with primers being too loose.
 
To me it looks like you took off way too much material when you used the drill. I would not do it that way.
 
I've been using the Lyman hand tool to remove the military crimp for decades....I just finished doing 500 military 7.62 and in the past hundreds of 30-06. There is no way the primer crimp removing tool did that.
What it looks like is you chucked a case deburring tool in the drill and used the inside neck deburring part to ream out the pocket. Wrong tool , too much brass has been removed...don't shoot those.
You can use that tool to remove just the crimped/diplaced metal from around the pocket edge , not nearly as much as in photo , and then finish up with a primer pocket reamer and then a primer pocket uniformer. Safest way is by hand....the power drill just went way too far .
Make the pockets look like a factory case pocket....no factory case will look like that , compare them .
Gary
 
I reamed 3000 9mm military brass recently. I tried using the Lyman pocket reamer but still had trouble seating primers. So, I got out the Dillon swager which worked well on about 90% of the brass. I used the Lyman reamer on the brass that still needed work. After all that a few pieces I just recycled.

The pic the OP posted indicates he used the wrong tool and destroyed the brass.
 
Last edited:
S&WIowegan said:
I reamed 3000 9mm military brass recently. I tried using the Lyman pocket reamer but still had trouble seating primers. So, I got out the Dillon swager which worked well on about 90% of the brass. I used the Lyman reamer on the brass that still needed work. After all that a few pieces I just recycled.

The pic the OP posted indicates he used the wrong tool and destroyed the brass.
Click to expand...

I have to use the sharp small blade of my pocket knife to remove most of the crimp, next a CH4D pocket reamer and finish with a Lyman pocket uniformer. I never could get 100% satisfaction with my old RCBS pocket swage die that installed in my press. The pen knife , reamer and uniformer will do the job.

Gary
 
The RCBS until works very well. The adjustment must be exact or results will probably be less than satisfactory. It does take a few minutes to do things properly, but this only needs to be done once.
 
You must log in or register to reply here.

Latest posts

Back
Top