|
|
11-04-2020, 09:00 PM
|
SWCA Member
|
|
|
Join Date: Dec 2006
Location: NW Florida
Posts: 2,235
Likes: 6,437
Liked 3,432 Times in 587 Posts
|
|
Reloading Cast Bullets Problem
I reload for all of my guns and use cast bullets for the old timer S&Ws and Winchesters. Of late I am having a lot if issues with bottle neck rounds for my 30-30 and 32ws. Seems like after full length resizing the case fits into the chamber perfectly, but after the bullet is pressed into the neck it will not chamber in the Winchester lever guns. I have checked the AOL and its within specs. What's happening and how do I fix it. Thanks for your help.
|
11-04-2020, 09:14 PM
|
Member
|
|
|
Join Date: Jan 2001
Location: In The Woods Of S.C.
Posts: 9,012
Likes: 14,262
Liked 13,962 Times in 5,062 Posts
|
|
Too much neck diameter after seating bullets or you're getting neck setback when seating the bullet.(causing the neck to grow in diameter). Are your bullets sized .308-.309? LEE makes a factory crimp die with carbide sizer that may cure your problem.
__________________
S&W Accumulator
|
The Following 2 Users Like Post:
|
|
11-04-2020, 09:18 PM
|
|
Member
|
|
|
Join Date: Jul 2017
Location: Pittsburgh PA
Posts: 1,753
Likes: 1,648
Liked 3,117 Times in 1,014 Posts
|
|
Bullet diameter may be too large for the throat. I had this issue with a 45-70
Try chambering a loaded round and ejecting it to see if there’s marks on the bullet from the throat
__________________
-Matt
|
The Following User Likes This Post:
|
|
11-04-2020, 09:52 PM
|
|
Member
|
|
|
Join Date: Mar 2012
Location: Upstate, SC
Posts: 2,057
Likes: 3,160
Liked 4,917 Times in 1,562 Posts
|
|
You would be well advised to make a chamber cast using CERRO-SAFE. Do a search and you'll find a ton of info.
Basically, the neck diameter of you loaded round likely exceeds the throat diameter in your rifle. The neck diameter of the loaded round is as follows: case neck thickness multiplied by two added to the diameter of the cast bullet.
If this value exceeds the chamber diameter, your solution is a thinner case neck. Just making up numbers, if your loaded round has a neck diameter of, say, .322" and your chamber is only .320", it will not chamber. Using a case with a neck wall thickness .001" less will allow it to chamber snugly. For safety and reliability, you probably want it a shade thinner.
There are two ways to accomplish this goal:
1) Use cases with thinner case wall thickness.
2) Turn your cases with an outside case turner. These can be had from Sinclair and, possibly, Brownell's (same parent company).
Others might suggest sizing the bullets smaller. But, if you have cast and sized them to match your rifle, modifying the cases (or using thinner cases) is the better solution.
|
The Following User Likes This Post:
|
|
11-04-2020, 10:29 PM
|
Member
|
|
|
Join Date: Mar 2015
Location: Arizona
Posts: 75
Likes: 308
Liked 106 Times in 41 Posts
|
|
Quote:
Originally Posted by Mike, SC Hunter
Too much neck diameter after seating bullets or you're getting neck setback when seating the bullet.(causing the neck to grow in diameter). Are your bullets sized .308-.309? LEE makes a factory crimp die with carbide sizer that may cure your problem.
|
The Lee FCD for bottleneck rounds is a completely different setup than the pistol FCD. The bottleneck FCD is a collet type crimper, the pistol FCD has an adjustable crimp sleeve, plus a carbide sizer.
|
11-04-2020, 11:05 PM
|
Member
|
|
|
Join Date: Jan 2001
Location: In The Woods Of S.C.
Posts: 9,012
Likes: 14,262
Liked 13,962 Times in 5,062 Posts
|
|
Also you could try seating your bullets a little deeper. I shoot Lee cast 150 grs. w/GS in my old 94. But never had a problem.
Remove the decapping stem from your sizing die. Lube a reloaded round and run it through the sizer. Then see if it chambers easily.
__________________
S&W Accumulator
|
The Following 2 Users Like Post:
|
|
11-04-2020, 11:14 PM
|
Member
|
|
|
Join Date: Feb 2010
Posts: 1,100
Likes: 326
Liked 469 Times in 278 Posts
|
|
Your chamber should handle a .310" bullet just fine. I suspect your problem is that you need to trim your brass to the correct length. 30-30 brass is very stretchy.
I don't know your bullet profile, but you might check to make sure you're not hitting the rifling.
|
The Following 5 Users Like Post:
|
|
11-05-2020, 05:31 AM
|
|
Member
|
|
|
Join Date: Dec 2012
Location: (outside) Charleston, SC
Posts: 31,042
Likes: 41,743
Liked 29,305 Times in 13,854 Posts
|
|
I had a problem solved here a ways back......
I couldn't chamber 30-06
I trouble shot (troubleshooted?) everything I knew how to. Gauged, calipered everything.....
I got a LOT of great suggestions and ways to check them on the forum here. And I diligently checked everything.
One suggestion that was especially useful was to use a marker to black the cartridge and try to chamber it to determine where the problem was. It did show a problem with the shoulder angle.
Someone suggested I examine my dies. There was ring of lead inside one that apparently changed the shoulder angle because everything else checked out perfectly.
No idea how it got there, but my problem, that I had been working on and off for a couple of years, went away.
That was a real Reloading Forum victory.
__________________
"He was kinda funny lookin'"
|
The Following 3 Users Like Post:
|
|
11-05-2020, 05:40 AM
|
Member
|
|
|
Join Date: Jan 2008
Location: Harlem, Ohio
Posts: 14,520
Likes: 23,797
Liked 26,578 Times in 9,197 Posts
|
|
One other thing you could check for, is a very slight bulge in the shoulder. this would come from the case mouth being too long and being pushed back while crimping OR the whole neck being pushed back while seating. This is a common problem with the older cartridges, I've had it with 30-30, 44-40, and some people have this problem in 25-20 & 32-20.
The cures:
1) Lee FDC (least likely!)
2) Trim cases to length (most likely)
3) clean the inside of your #2 die (easy and free, so why not!)
4) all of the above
Ivan
|
The Following 3 Users Like Post:
|
|
11-05-2020, 10:55 AM
|
|
Member
|
|
|
Join Date: Jul 2010
Location: Florida
Posts: 6,685
Likes: 3,443
Liked 9,386 Times in 3,527 Posts
|
|
If you've been loading cast bullets all along for those two rifles, examine what has possibly changed when the issue began--different bullet weight/style, COL, different brass, etc.
I'd clean the dies, get some new cases, do all the initial case prep, check diameter of the bullets, and load a few and try chambering again.
|
The Following 2 Users Like Post:
|
|
11-05-2020, 11:30 AM
|
Member
|
|
|
Join Date: Feb 2007
Location: SW MT
Posts: 6,793
Likes: 10,642
Liked 6,094 Times in 3,003 Posts
|
|
Going to the RCBS X die in 30-30 has eliminated case stretching in my guns. They do work as advertised.
__________________
Front sight and squeeze
|
11-05-2020, 01:23 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: S. Orygun
Posts: 2,462
Likes: 1,971
Liked 1,829 Times in 988 Posts
|
|
Quote:
Originally Posted by Mike, SC Hunter
Too much neck diameter after seating bullets or you're getting neck setback when seating the bullet.(causing the neck to grow in diameter). Are your bullets sized .308-.309? LEE makes a factory crimp die with carbide sizer that may cure your problem.
|
First part correct. Cast bullets are normally larger in diameter and will swell the case neck often too much to fit the chamber/throat. Any time there is a fit issue, measure. Measure the completed handload to find out where it is too big and that will show what to correct. Or measure the case after each step to find out when the problem happens...
The Lee post crimping sizing die is used mainly for hand gun cartridges and not for 30-30, or other bottle necked cartridges. Lee makes an excellent collet crimp die for bottle necked cases.
|
The Following User Likes This Post:
|
|
11-05-2020, 01:44 PM
|
Member
|
|
|
Join Date: Oct 2014
Location: Monroe cnty. Ohio
Posts: 6,971
Likes: 4,440
Liked 10,094 Times in 3,703 Posts
|
|
I would bet a beer it’s as Ivan said. Several reasons that result in shoulder set back that causes a roll at shoulder. Put magic marker on shoulder area.
Attempt to chamber and when you feel resistance, extract and check shoulder to see if marker is wiped off.
|
The Following 2 Users Like Post:
|
|
11-14-2020, 04:55 PM
|
Member
|
|
|
Join Date: May 2010
Location: Pennsylvania
Posts: 1,704
Likes: 1,538
Liked 1,834 Times in 741 Posts
|
|
Crimping bottle neck cartridges is a pita. If case lengths varies too much it is easy to bulge the case when the bullet is crimped on a longer case. Bottle neck cases also tend to require trimming more often than straight walled ones, the shoulder angle being conducive to brass flow resulting in an over long neck. It's also another good reason to segregate you brass by manufacturer.
John
|
11-14-2020, 05:44 PM
|
Member
|
|
|
Join Date: Jun 2014
Posts: 2,368
Likes: 5,518
Liked 2,811 Times in 1,277 Posts
|
|
Did this ever get sorted out?
__________________
Just Say No - To Social Media
|
11-16-2020, 01:17 AM
|
|
Member
|
|
|
Join Date: Feb 2006
Location: Kalif. usa
Posts: 6,836
Likes: 2,665
Liked 3,927 Times in 2,366 Posts
|
|
Quote:
Originally Posted by delta-419
I reload for all of my guns and use cast bullets for the old timer S&Ws and Winchesters. Of late I am having a lot if issues with bottle neck rounds for my 30-30 and 32ws. Seems like after full length resizing the case fits into the chamber perfectly, but after the bullet is pressed into the neck it will not chamber in the Winchester lever guns. I have checked the AOL and its within specs. What's happening and how do I fix it. Thanks for your help.
|
Are you using a Lyman M style expander? If so,you need a modest crimp to remove the flare. If not, are you scraping the bullet & leaving a small ring of lead at the case mouth?
__________________
NRA Cert. Inst. IDPA CSO
|
|
Posting Rules
|
|
|
|
|