|
|
05-02-2024, 09:21 AM
|
Member
|
|
|
Join Date: Dec 2008
Location: Arkansas
Posts: 117
Likes: 39
Liked 70 Times in 36 Posts
|
|
Need help with 38 Short Colt buldge!
I am reloading 38 short colt starline brass using 160 gr coated bullets .358 in diameter. They are causing my cases to bulge and therefore they will not completely enter the case checker.
I have been using 160gr with .357 diameter with little problem.
Is there a secret to keeping these things from bulging the case.
Your assistance will be greatly appreciated.
|
05-02-2024, 01:22 PM
|
Member
|
|
|
Join Date: Jan 2012
Location: Northern IL
Posts: 163
Likes: 215
Liked 379 Times in 74 Posts
|
|
I load the same exact thing, I can double check when I get home but I am almost positive I use a Lee Factory Crimp Die
|
The Following User Likes This Post:
|
|
05-02-2024, 02:11 PM
|
Member
|
|
|
Join Date: Dec 2008
Location: Arkansas
Posts: 117
Likes: 39
Liked 70 Times in 36 Posts
|
|
I use a Lee Factory crip die in 9mm. If you have a case guage, see if your loads drop in all the way. Mine lack about 1/4 inch going all thev way in the case gage.
Last edited by rd97; 05-02-2024 at 02:14 PM.
Reason: clarify comment
|
05-02-2024, 02:27 PM
|
SWCA Member
|
|
|
Join Date: Jun 2011
Location: Tulsa OK
Posts: 1,521
Likes: 672
Liked 1,631 Times in 705 Posts
|
|
Never heard of a 160 grain bullet - all mine are 158 grain if they are cast or jacketed. Where would one buy a 160 grain bullet?
__________________
S&WHF #946
S&WCA #3824
|
05-02-2024, 02:35 PM
|
Member
|
|
|
Join Date: Sep 2003
Location: Ohio
Posts: 713
Likes: 1,335
Liked 716 Times in 274 Posts
|
|
You mentioned that your reloads will not fully enter your case checker. Will they chamber in your revolver? If they do, you don't have a problem. If they won't chamber in your revolver, your choices would be:
1. Use .357 bullets instead of .358.
2. Use the Lee FCD as suggested.
3. Use thinner wall brass (probably not findable).
I see the same bulge in my .38 Special reloads with .358 bullets and have never had a problem with chambering in a variety of revolvers from 1899 to the present.
|
The Following 2 Users Like Post:
|
|
05-02-2024, 02:51 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: S. Orygun
Posts: 2,463
Likes: 1,974
Liked 1,831 Times in 989 Posts
|
|
Have you done a plunk test? I have had a few problems with handloads that would not pass a gauge test, but fed and fired quite well, no problems...
|
The Following 2 Users Like Post:
|
|
05-02-2024, 06:47 PM
|
Member
|
|
|
Join Date: Dec 2008
Location: Arkansas
Posts: 117
Likes: 39
Liked 70 Times in 36 Posts
|
|
Quote:
Originally Posted by Model19man
Never heard of a 160 grain bullet - all mine are 158 grain if they are cast or jacketed. Where would one buy a 160 grain bullet?
|
Bang and Clang/Bayou Bullets for a couple. They are coated bullets.
|
05-02-2024, 06:50 PM
|
Member
|
|
|
Join Date: Dec 2008
Location: Arkansas
Posts: 117
Likes: 39
Liked 70 Times in 36 Posts
|
|
Quote:
Originally Posted by HKSmith
You mentioned that your reloads will not fully enter your case checker. Will they chamber in your revolver? If they do, you don't have a problem. If they won't chamber in your revolver, your choices would be:
1. Use .357 bullets instead of .358.
2. Use the Lee FCD as suggested.
3. Use thinner wall brass (probably not findable).
I see the same bulge in my .38 Special reloads with .358 bullets and have never had a problem with chambering in a variety of revolvers from 1899 to the present.
|
I normally use 357. This was my first time to use 358. They will chamber so I will may use them for practice but use 357's for competition because I have such good luck with them. I do use the lee FCD. Thanks for your info.
Last edited by rd97; 05-02-2024 at 06:52 PM.
|
The Following User Likes This Post:
|
|
05-02-2024, 08:06 PM
|
SWCA Member
|
|
|
Join Date: Jun 2011
Location: Tulsa OK
Posts: 1,521
Likes: 672
Liked 1,631 Times in 705 Posts
|
|
Quote:
Originally Posted by rd97
Bang and Clang/Bayou Bullets for a couple. They are coated bullets.
|
Interesting. I use Bang and Clang but I normally use this bullet:
158 grain 38/357 and 9MM SWC sized 0.356-0.358 Coated - Bang and Clang LLC
__________________
S&WHF #946
S&WCA #3824
|
05-02-2024, 08:37 PM
|
Member
|
|
|
Join Date: Dec 2008
Location: Arkansas
Posts: 117
Likes: 39
Liked 70 Times in 36 Posts
|
|
I really like the round nose bullet. I think the 358 diameter will work better in the 38 special brass. I will load some of those and see how they run.
|
05-02-2024, 09:45 PM
|
|
Member
|
|
|
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,899
Likes: 254
Liked 29,569 Times in 14,263 Posts
|
|
If the rounds will chamber fully, I wouldn't worry about doing anything.
|
The Following 2 Users Like Post:
|
|
05-03-2024, 02:12 AM
|
|
Member
|
|
|
Join Date: Dec 2012
Location: (outside) Charleston, SC
Posts: 31,075
Likes: 41,789
Liked 29,344 Times in 13,867 Posts
|
|
What kind of gauge do you have?
My gauges are CARTRIDGE LENGTH gauges from Wilson and are not that great for chambering testing. I plunk in the barrel before I reject a loaded cartridge that won't fit in the gauge.
Does anybody have gauges that are made for chambering testing?
__________________
"He was kinda funny lookin'"
|
05-03-2024, 09:04 AM
|
Member
|
|
|
Join Date: Dec 2008
Location: Arkansas
Posts: 117
Likes: 39
Liked 70 Times in 36 Posts
|
|
Mine is a Wilson also.
|
05-03-2024, 09:38 AM
|
|
Member
|
|
|
Join Date: Apr 2012
Location: Houston, TX
Posts: 3,855
Likes: 1,685
Liked 6,522 Times in 2,381 Posts
|
|
Is the bulge even all away around the cartridge?
|
05-03-2024, 11:19 AM
|
Member
|
|
|
Join Date: Dec 2008
Location: Arkansas
Posts: 117
Likes: 39
Liked 70 Times in 36 Posts
|
|
Yes it is.
|
05-03-2024, 04:03 PM
|
Member
|
|
|
Join Date: Dec 2008
Location: Arkansas
Posts: 117
Likes: 39
Liked 70 Times in 36 Posts
|
|
Thanks for all your responses. You helped me to decide a reasonable solution. I plan on resizing the 358 to 357 and stick with what I know works. Seems I’m always tinkering to my own destruction. If it ain’t broke don’t fix it!!
|
05-03-2024, 04:50 PM
|
|
US Veteran
|
|
|
Join Date: Dec 2011
Location: WA.
Posts: 4,461
Likes: 4,520
Liked 4,498 Times in 2,193 Posts
|
|
I load 125 gr. RN. I think they're .358 but not sure. 125-135 gr was the original weight for this cartridge. 158 gr is the original weight for 38 Spl. which is a much larger case. I'll have to look but I think I use a Lee FDC also.
__________________
That's just somebody talkin.
|
05-05-2024, 11:26 AM
|
|
Member
|
|
|
Join Date: Jan 2007
Location: Sandy Utah
Posts: 8,835
Likes: 1,632
Liked 9,131 Times in 3,627 Posts
|
|
Just where is the bulge in the case? If it is at the base of the bullet then don't seat them so deeply. If it is the entire bullet shank then use .357 bullets!
Finally, just why are you using a cartridge gauge to check your ammunition? If the cartridges freely enter the chambers of your revolver then they are fine. Throw the damned case gauge away, you don't need it!!!!! The "plunk check" is intended to check the ammunition in the gun it will be used in, you don't plunk check in a case gauge!
__________________
Gunsmithing since 1961
|
The Following 2 Users Like Post:
|
|
05-05-2024, 05:16 PM
|
Member
|
|
|
Join Date: Sep 2005
Posts: 7,784
Likes: 1,648
Liked 9,227 Times in 3,407 Posts
|
|
You said you had little issue loading with .357d (coated?) 160gr bullets.
I would guess that the .358d Coated bullet is the main culprit.
Not knowing exactly where the bulge is,,the use of a 9mm Lee FCDie may
be bulging the brass as well with the oversize bullet.
A 9mm bullet is generally .356d
Adding the extra .000's to the equation and then using a smaller crimp die can't be a good thing.
|
The Following User Likes This Post:
|
|
05-10-2024, 05:57 PM
|
|
Member
|
|
|
Join Date: Nov 2004
Location: Mountain State
Posts: 3,603
Likes: 99
Liked 389 Times in 157 Posts
|
|
For the short colt I always loaded 148 gr. Berry Bullets. 158gr. I found was to heavy for the short colt. Plus to load easier I load 148gr 9mm rounds.
|
|
Posting Rules
|
|
|
|
|