|
|
04-28-2015, 10:49 PM
|
Member
|
|
|
Join Date: Jan 2004
Location: Barrackville, WV, US
Posts: 598
Likes: 12
Liked 84 Times in 48 Posts
|
|
.38 Special ammo
I just bought a Military&Police .38 and looking for some good factory loads for it. Serial# S834XXX so it looks to be dated to around the end of WWII I believe. Any recommendations for a good low pressure load for a revolver of this era? Thanks for your help!
|
04-28-2015, 11:14 PM
|
Member
|
|
|
Join Date: Aug 2003
Location: Occupied California
Posts: 2,793
Likes: 1,527
Liked 5,592 Times in 1,613 Posts
|
|
The regular 158 grain lead round nosed .38 Special load (non +P) will work best. They are easy on the gun, usually accurate and most importantly, will shoot to the sights as that is what the old fixed sight guns were regulated to.
|
The Following User Likes This Post:
|
|
04-29-2015, 12:01 AM
|
|
US Veteran
|
|
|
Join Date: Mar 2011
Location: Palmer, Alaska
Posts: 14,505
Likes: 5,123
Liked 19,061 Times in 6,882 Posts
|
|
Your revolver most likely shipped from the factory in August, 1946. Pictures would be nice.
Walter's answer regarding ammo is correct. While jacketed loads will be safe, it would be easier on the gun if you stick to lead bullets.
__________________
Jack
SWCA #2475, SWHF #318
|
The Following User Likes This Post:
|
|
04-29-2015, 12:07 AM
|
|
Member
|
|
|
Join Date: Mar 2014
Location: New Hampshire
Posts: 2,847
Likes: 8,671
Liked 3,497 Times in 1,342 Posts
|
|
The Armscor .38 Spl 158gr FMJ is light and clean. Great brass for reloading too! I use this in my Victory .38 Spl.
Jim
|
04-29-2015, 10:53 AM
|
Member
|
|
|
Join Date: Jan 2014
Location: Northern Virginia
Posts: 171
Likes: 638
Liked 155 Times in 61 Posts
|
|
I find that the 148g WC work very well in those old guns. I get it from Georgia Arms.
|
The Following User Likes This Post:
|
|
04-29-2015, 11:29 AM
|
|
SWCA Member
|
|
|
Join Date: Feb 2005
Location: Cocoa Beach, Florida
Posts: 10,585
Likes: 3,075
Liked 22,577 Times in 5,847 Posts
|
|
There is always Winchester, Federal, Remington, Hornady and Speer
All of them make several choices in safe ammunition for your revolver. Most or them have been doing so since the day your revolver was New
|
04-29-2015, 12:44 PM
|
|
Member
|
|
|
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,644
Likes: 242
Liked 29,156 Times in 14,097 Posts
|
|
You can use any .38 Special ammunition you wish. But those with lead bullets are best.
|
04-29-2015, 01:54 PM
|
|
US Veteran
|
|
|
Join Date: Dec 2013
Location: Pennsylvania
Posts: 116
Likes: 11
Liked 138 Times in 60 Posts
|
|
I've always had good luck with the Remington or Winchester 130gr FMJ. Light bullet, moderate velocity and pressure. And then you get brass to reload!
|
04-29-2015, 06:44 PM
|
Member
|
|
|
Join Date: Jan 2011
Location: east tennessee, union co
Posts: 176
Likes: 85
Liked 114 Times in 51 Posts
|
|
Cant find much 38 specials around here, why are they hard to find.
|
04-29-2015, 07:31 PM
|
|
SWCA Member
|
|
|
Join Date: May 2005
Location: Michigan
Posts: 9,320
Likes: 34,034
Liked 10,993 Times in 3,961 Posts
|
|
I like to shoot 158 grain bullets in fixed sight S&W .38 Special revolvers, although 148 grain target loads are also great and easier on you and the gun.
Realistically, any standard factory load using a 158 grain bullet (jacketed or lead) would take an awful lot of shooting before it could produce any detectible wear on the gun.
My local Wal-Mart had a reasonable supply of Winchester and Federal .38 Specials on hand the last few times I was there.
__________________
You're shy a few manners.
|
The Following User Likes This Post:
|
|
04-29-2015, 08:28 PM
|
Member
|
|
|
Join Date: Dec 2008
Location: Seattle
Posts: 1,947
Likes: 38
Liked 821 Times in 490 Posts
|
|
I'll echo DWalt's post in saying that your M&P will handle any factory-loaded .38 Special ammo safely, but will be at its best with a 158-160 gr. lead (RN or SWC) service-type load (approx. 800-850 fps). The 148 gr. Midrange Wadcutters will be good at the range, easy on both gun and shooter, and even the Buffalo Bore +P load, which approximates the old .38-44 HV load, will be safe, but will indeed accelerate wear on the gun. If you should encounter any of the Winchester or Federal 130 gr. FMJ for cheap, buy them. It's an utterly wimpy load, being the commercial equivalent of the military M41 Ball, but the fired brass will be first-rate for reloading.
Larry
Last edited by lebomm; 04-29-2015 at 08:29 PM.
|
04-30-2015, 07:51 AM
|
|
Member
|
|
|
Join Date: Sep 2009
Location: Hillsdale, Mi.
Posts: 7,502
Likes: 7,046
Liked 7,090 Times in 2,944 Posts
|
|
You could enter the world of Reloading! My .38's/.357's love 148gr. lead wadcutters. If you get components priced right it is cost effective. I have loaded .38 Special as low as $3.48 for a box of 50. YES, there is a start up cost factor! Bob
|
|
Posting Rules
|
|
|
|
|