Here goes my first post so be gentle. I know I'm in the right church, but perhaps the wrong pew.

My father-in-law passed last month with a safe full of guns. I am trying to help my mother-in-law sell whats left after I get frist dibs, but I need some help with model numbers.

The first gun is a .38 CTG with a 5" barrel. Serial #D1406XX

The second gun is a .38 snub nose serial #J745XX

The third is a .32 US Revolver Co. Top Break serial #482XX (which I think is a S&W copy)

The last one is a "Made in Spain" .38 5 shot Top break serial #5292 with no other markings on it.

Any help would be greatly appreciated. I want to get her the most bang for the buck (no pun intended) and want to price them correctly with the right Model #. I know I could call S&W directly, but would rather tap the wealth of knowledge here on the forum. Thanks in advance for whatever information you can help with. I am going over to her house today to take pictures, so I can post them later.

Harry

I would recommend standard catalog of firearms or the blue book of gun values. Both are good sources of firearm prices. However, they are not etched in stone. Prices fluctuate and they are just a guide. If the buyer wants the gun bad enough, price is subjective. Hope this helps and good luck.

Nick

If they don't have a model number stamped on the gun (on the frame under the yoke) then they were made before 1957 when Smith and Wessons had names, not numbers. For certain identification post clear pictures.

Typically the model number is found on the crane of the gun.
Open the cylinder and you should see the model # there.

Welcome to the Forum. As noted, model numbers and photos would be helpful for the two Smith & Wessons. Best guess is that you have a K frame (Model 10????) from 1969 and a J frame (Model 36 ????) from the same year. Their value will vary greatly by condition, so again, photos would help.

The other two revolvers fall into the old "Saturday Night Special" category and sight unseen are going to fetch less than $100 each on the market.

Best of luck.

The Model 10 ? will depend on the length of the barrel which is measured from the front of the cylinder to the end of the barrel. The 4 inch barrel is worth more then the 6 inch barrel and then the rest of the price is based on the condition of the two S&W revolvers. The J frame Model 36 can be worth a more then the Model 10 if it's a snub nose and in good condition because they are popular as a carry revolver.

I have to say I am always so impressed with the willingness of the members here to offer assistance to those not in the know. This forum is a great resource.

Sounds like an interesting project. Pictures would be helpful as condition is key to determining value. The first two should be model marked on the inside of the frame. Open the cylinder and look on the frame above the cylinder pivot,in front of the cylinder opening and below the rear end of the barrel. You should see something like MOD 10 or MOD 36 etc along with some other numbers.
The US Revolver top break was made by Iver Johnson. Depending on condition, these usually go for between $25-75, if they work. Exceptional examples with original boxes would go for much more to the right buyer. The last is a Spanish knock off and is probably worth about $25-100, again, depending on condition.
I see your a Pa boy too! Where are you located?
John

Harry,By chance, are you in central or eastern Pennsylvania?

__________________
That's what we do!

Thanks for all the quick and informative posts. This is great. I will take a closer look when I take pictures today. Thanks again. I will keep you posted.

I am located in SE PA. Montgomery County.

Harry

Harry,I have been very fortunate to work with and buy several S&W revolvers from a LGS owner in Nazareth, PA. He works with collectors and estate sales. Best of all, he's honest and truthful. He's first class in my book.You'll get some great information and advice from the professionals on this website. All you have to do is ask. You can't beat the price either!!

__________________
That's what we do!