|
|
09-06-2014, 02:25 AM
|
Member
|
|
|
Join Date: Mar 2005
Location: Backwoods Louisiana
Posts: 763
Likes: 210
Liked 285 Times in 113 Posts
|
|
Repairing Target Grips
The target grips on my Highway Patrolman shift out of alignment slightly, particularly when the gun is fired. I have to squeeze the grips to pop them back into place. This is apparently because the hole on one side of the grips was chipped putting the on the gun. I tried shifting the rod that goes through the frame to put it deeper into the hole, but that doesn't seem to work
Is there a solution to fixing these grips? What about filling the hole with epoxy and recutting the hole?
|
09-06-2014, 02:46 AM
|
Member
|
|
|
Join Date: Mar 2012
Location: Prescott Valley, AZ
Posts: 462
Likes: 1,365
Liked 388 Times in 169 Posts
|
|
Filling the hole and redrilling it would probably work as long as you can drill a new hole that’s the right size and correctly aligned. I don’t know how this would work but I would be tempted the coat the area with a heavy lub like Vaseline to protect the metal then use very little epoxy in the hole and put the grip in place for the epoxy to form around the pin.
Someone will probably be along with a more professional way of doing it.
|
09-06-2014, 02:57 AM
|
|
US Veteran
|
|
|
Join Date: Mar 2012
Location: E. Washington State
Posts: 5,498
Likes: 1,325
Liked 10,608 Times in 3,231 Posts
|
|
Quote:
Originally Posted by Twiki357
Filling the hole and redrilling it would probably work as long as you can drill a new hole that’s the right size and correctly aligned. I don’t know how this would work but I would be tempted the coat the area with a heavy lub like Vaseline to protect the metal then use very little epoxy in the hole and put the grip in place for the epoxy to form around the pin.
Someone will probably be along with a more professional way of doing it.
|
That's what I was thinking, or plastic wood mite work.
__________________
Only difference Fool/Mule-ears
|
09-06-2014, 06:06 AM
|
|
Member
|
|
|
Join Date: Sep 2009
Location: Hillsdale, Mi.
Posts: 7,502
Likes: 7,047
Liked 7,090 Times in 2,944 Posts
|
|
I have never had an issue with grips coming off. Filling & re-drilling makes sense, but you would have to be precise. You could make an insert of rigid tubing or other to put over the pin to better fit the hole. I have never done it, but would work. Grips not altered, gun not altered. Bob
|
09-06-2014, 10:28 AM
|
US Veteran
|
|
|
Join Date: Feb 2009
Location: Ozarks of Missouri
Posts: 3,329
Likes: 3,009
Liked 2,922 Times in 992 Posts
|
|
Quote:
Originally Posted by Twiki357
Filling the hole and redrilling it would probably work as long as you can drill a new hole that’s the right size and correctly aligned . . .
|
I also like the idea of filling & re-drilling the hole. To get the new hole in the right place, I would remove the stock alignment pin, hold the repaired stock panel in the exact position, and mark the stock panel through the hole in the frame.
To get a good mark, I would use a drill bit that just fits through the pin hole but hold it in your hand or in a small hand-held chuck to get the hole started . . . or your can go ahead and finish drilling the hole by hand using the pin hole as an alignment guide.
Good luck,
Russ
|
The Following 4 Users Like Post:
|
|
09-06-2014, 11:04 AM
|
|
Member
|
|
|
Join Date: Mar 2006
Location: Colorado
Posts: 15,141
Likes: 91,884
Liked 26,408 Times in 8,418 Posts
|
|
Slather Vaseline or oil on the pin and frame.Put a bit of epoxy in the hole of the grip.Install the grips and align them while keeping the damaged grip on the bottom and let the glue dry for a few hours.
|
The Following User Likes This Post:
|
|
09-06-2014, 12:00 PM
|
|
Member
|
|
|
Join Date: Mar 2005
Location: DPRK (CA)
Posts: 1,498
Likes: 369
Liked 1,273 Times in 466 Posts
|
|
fill the hole with super glue, epoxy can separate from the wood, super glue will take wood with it if it comes to that. You may not even need to completely fill the hole, reducing the diameter may solve your problem.
|
The Following 3 Users Like Post:
|
|
09-06-2014, 02:05 PM
|
|
US Veteran
|
|
|
Join Date: Dec 2004
Location: Connecticut Yankee
Posts: 2,380
Likes: 744
Liked 3,575 Times in 789 Posts
|
|
Both Russ and John are right on track. The only trick is to make sure you align the panel correctly or the new hole will be in the wrong place. Also I would use gel super glue and stuff a little wood dust in on top of the super glue, Let it harden, sand flush and then drill your hole. Good luck.
DW
__________________
"NUTS"
|
The Following User Likes This Post:
|
|
09-06-2014, 08:55 PM
|
Member
|
|
|
Join Date: Dec 2009
Location: Georgia
Posts: 437
Likes: 43
Liked 114 Times in 52 Posts
|
|
If it's only off diameter by 5 or 10 thousandths of an inch, I would try to put a slice of veneer in the hole. That would be less permanent to start with and would not require any drilling. When you get the right placement and the right thickness you can put a dab of yellow glue on the veneer to hold it in place using a drill shank or perhaps an appropriately sized finishing nail.
|
09-06-2014, 10:50 PM
|
|
Member
|
|
|
Join Date: Mar 2009
Location: central pa
Posts: 5,336
Likes: 2,745
Liked 2,492 Times in 1,182 Posts
|
|
Quote:
Originally Posted by Twiki357
Filling the hole and redrilling it would probably work as long as you can drill a new hole that’s the right size and correctly aligned. I don’t know how this would work but I would be tempted the coat the area with a heavy lub like Vaseline to protect the metal then use very little epoxy in the hole and put the grip in place for the epoxy to form around the pin.
Someone will probably be along with a more professional way of doing it.
|
I have done this many times fitting grips to single actions with good results using JB Weld. For a release agent I apply a lite coat of any old gun oil to pin and frame areas that may come into contact with the JB Weld.
__________________
Stay safe people!
|
|
Posting Rules
|
|
|
|
|