|
|
04-16-2024, 05:44 PM
|
Member
|
|
|
Join Date: Dec 2017
Posts: 103
Likes: 18
Liked 145 Times in 64 Posts
|
|
Anyone cut a model 28 HP to 3-1/2"?
With all the rage for the model 27 in 3-1/2" barrel, has anyone cut a 4" model 28 to 3-1/2"? Although the model 28 has reached it's own status as an affordable N frame is this a doable project and does anyone have one to show? Also for the front sight how much higher will the new front sight have to be for the shortened barrel
Thanks in advance for any replies or pertinent information.
|
04-16-2024, 05:54 PM
|
Member
|
|
|
Join Date: Sep 2018
Posts: 1,885
Likes: 2,276
Liked 2,979 Times in 1,110 Posts
|
|
My experience with cutting an N-frame clone from 6” to 3” was that the front sight needed to be *lower*, not higher.
I get the urge for something specific, but for me 1/2” wouldn’t be worth the work.
__________________
Uvidíme se později, aligátore.
|
The Following 7 Users Like Post:
|
|
04-16-2024, 06:08 PM
|
|
Member
|
|
|
Join Date: Mar 2023
Location: Northeast MS
Posts: 647
Likes: 2,410
Liked 1,889 Times in 445 Posts
|
|
If it were mine, I would leave it as is.
|
The Following 2 Users Like Post:
|
|
04-16-2024, 07:00 PM
|
SWCA Member
|
|
|
Join Date: Feb 2014
Location: VA & SoFL
Posts: 8,717
Likes: 474
Liked 5,768 Times in 3,223 Posts
|
|
Why not just buy a m-27, 3.5" barre? Leave the m-28 alone.
__________________
Mike 2796
SoFo Bunch member
|
The Following 7 Users Like Post:
|
|
04-16-2024, 07:34 PM
|
Member
|
|
|
Join Date: Feb 2024
Posts: 48
Likes: 0
Liked 90 Times in 19 Posts
|
|
Don’t do it. 28’s are 28’s for a reason. Agree, with the 27 3.5” advice but be ready to pay for it.
|
04-16-2024, 08:17 PM
|
|
US Veteran
|
|
|
Join Date: Oct 2013
Location: Central Montana
Posts: 13,748
Likes: 12,913
Liked 39,640 Times in 10,078 Posts
|
|
I can't see the amount of work vs the gain of trimming a 1/2''. But, If I wanted a 3 1/2" Model 28 I would start with a 6" barrel. Easier to come by, you could cut of the whole ramp and front sight turn it over machine it to have a "key" on the bottom. Then make a slot in the rib of cut down portion to have a good mount up.
Lot of work to loose a 1/2" though.
|
The Following 8 Users Like Post:
|
|
04-16-2024, 08:37 PM
|
Member
|
|
|
Join Date: May 2013
Location: Denver area
Posts: 6,271
Likes: 20,320
Liked 13,163 Times in 4,193 Posts
|
|
If you do it, you’ll end up with a gun that most will see as Buba’s weekend project.
|
The Following 3 Users Like Post:
|
|
04-16-2024, 08:46 PM
|
|
Member
|
|
|
Join Date: Jan 2007
Location: Sandy Utah
Posts: 8,756
Likes: 1,596
Liked 8,935 Times in 3,562 Posts
|
|
All of steelslaver's points are right on! The other side of this is why would you want to spend $300 or so to change a $1000+/- revolver into a $600 dollar gun that no one else would probably want!
The fact is that any 4" S&W revolver barrel can vary from as much as 1/8" longer to 1/4" shorter that nominal length. Would you want to "cut" the barrel to realize only a 1/2" change that could actually be as little as 1/4" to 1/8"? There is absolutely no utility in shortening a 4" barrel to Sure 3 1/2"at all! Can it be done, sure!
__________________
Gunsmithing since 1961
|
The Following 3 Users Like Post:
|
|
04-16-2024, 08:51 PM
|
Member
|
|
|
Join Date: Nov 2005
Location: VA
Posts: 4,679
Likes: 1,451
Liked 4,521 Times in 1,936 Posts
|
|
Now that is a project that will cost a bundle and take all the value out of your gun. Sell or trade your 28 on a 27 in your chosen barrel length and be done with it.
__________________
S&W factory revolver armorer
|
The Following 2 Users Like Post:
|
|
04-19-2024, 04:19 PM
|
|
SWCA Member
|
|
|
Join Date: Jun 2009
Location: Sadly, Seattle WA
Posts: 10,632
Likes: 22,976
Liked 10,380 Times in 4,308 Posts
|
|
3.5 inch 27 barrel on a 28.....makes this a 27 and a half????
__________________
Even older, even crankier....
Last edited by A10; 04-19-2024 at 04:21 PM.
|
The Following 4 Users Like Post:
|
|
04-19-2024, 06:05 PM
|
Member
|
|
|
Join Date: Dec 2017
Posts: 103
Likes: 18
Liked 145 Times in 64 Posts
|
|
I concede, it was just a random thought. The 3-1/2" barrel model 27's just seem to be rare as hens teeth in my area. So that got me thinking & that can be a dangerous thing sometimes.
But I do want to thank everyone who replied.
|
The Following 2 Users Like Post:
|
|
04-19-2024, 06:47 PM
|
|
Member
|
|
|
Join Date: Mar 2006
Location: Colorado
Posts: 15,163
Likes: 92,007
Liked 26,462 Times in 8,437 Posts
|
|
I seem to recall seeing one here that had been converted to 44special. That would be a cool project
|
04-19-2024, 07:53 PM
|
|
US Veteran
|
|
|
Join Date: Oct 2013
Location: Central Montana
Posts: 13,748
Likes: 12,913
Liked 39,640 Times in 10,078 Posts
|
|
I do have several model 28s and a pre model Highway Patrolmen, a 3 1/2" 44 special barrel as well as a 44 special reamer
|
The Following 2 Users Like Post:
|
|
|
Posting Rules
|
|
|
|
|