|
|
04-19-2024, 03:55 PM
|
Member
|
|
|
Join Date: Jun 2014
Location: Auburn, AL
Posts: 48
Likes: 3
Liked 287 Times in 30 Posts
|
|
She's Back!
Some of you may remember my post a while back about the sad Mdl. 19 that I traded for. Well the shop got it done sooner than expected, so I was able to pick her up today. The pitting on the right side was worse than I originally thought, so I opted for their satin finish. It doesn't hide all the defects, but it sure does make them less noticeable. Fortunately, I had time to restore the stocks while it was out, so I put them on as soon as I got home. I've attached before and after pics for comparison.
Is it a Ford's or Turnbull level job? Nope! But for a shooter, and at a fraction of the cost, it's works just fine for me.
|
The Following 79 Users Like Post:
|
22lrfan, A10, ameridaddy, AZ Buckshot Bill, Azav8or, Bajadoc, bananaman, Barbarian-CBX, Baxter6551, Bill Bates, Birdhunter6, boykinlp, browningcollector, C Islander, CajunBass, cbfd, Chuck Edwards, cndrdk, cololab, ColumbusJBR, D1911, deputydon, Dino44, drgbike, dsf, Ga Johnny, GeoJelly, H Richard, Hawg Rider, Heinz, housedog, hs125, JayCeeNC, jbtrucker, jeffrefrig, Jimmyjones, john in mich, jrc1, K Harris, kframeman, leonardocarrillo, Llance, long colt frazier, lppd4, M29since14, madmikeb, MarkHayden, mchom, MelvinWalker, Mike0251, moosedog, Muley Gil, Narragansett, Nightowl, OutAtTheEdge, pasound, PaulDoc, Pizza Bob, Protocall_Design, Retired W4, Richard Simmons, rincar, Rudi, S&W Fan, scooterfiend, scout II, Skyhunter, Slufstuff, Smith & Hammer, Squarebutt, stansdds, steve a., strike5, swagmeister, THE PILGRIM, TJm15.38, Toyman, usm1rifle, ZGrand |
04-19-2024, 04:01 PM
|
US Veteran
|
|
|
Join Date: Nov 2014
Location: central Virginia
Posts: 2,971
Likes: 13,503
Liked 7,097 Times in 2,145 Posts
|
|
Don't have to hide that one. Very nice!
|
The Following User Likes This Post:
|
|
04-19-2024, 04:04 PM
|
|
SWCA Member
|
|
|
Join Date: Jun 2009
Location: Sadly, Seattle WA
Posts: 10,632
Likes: 22,976
Liked 10,382 Times in 4,309 Posts
|
|
Turned out pretty darn nice!
__________________
Even older, even crankier....
|
The Following 2 Users Like Post:
|
|
04-19-2024, 04:10 PM
|
|
Member
|
|
|
Join Date: Jul 2014
Location: Mojave Desert
Posts: 10,434
Likes: 18,174
Liked 24,453 Times in 6,909 Posts
|
|
Looks good
What matte finish was applied?
__________________
213th FBINA
|
04-19-2024, 05:47 PM
|
|
SWCA Member
|
|
|
Join Date: Jul 2011
Location: North Texas
Posts: 1,434
Likes: 2,833
Liked 1,536 Times in 541 Posts
|
|
What finish did you use on the grips? They look great!
|
The Following User Likes This Post:
|
|
04-19-2024, 06:04 PM
|
|
SWCA Member
|
|
|
Join Date: Jan 2024
Location: Central Florida
Posts: 336
Likes: 318
Liked 663 Times in 202 Posts
|
|
I like it...Reminds me of the non-reflective blued type finish put on Model 28's...Stocks look great too.
|
The Following 2 Users Like Post:
|
|
04-19-2024, 06:19 PM
|
Member
|
|
|
Join Date: Feb 2014
Location: Home of the Pilgrims!
Posts: 83
Likes: 85
Liked 147 Times in 43 Posts
|
|
Looks great, grips are even nicer! Looks like a 80% version of a Model 28, but with "fancy" lumber. I love it! Bill in MA
|
The Following User Likes This Post:
|
|
04-19-2024, 06:40 PM
|
Member
|
|
|
Join Date: Dec 2012
Location: Connecticut
Posts: 1,479
Likes: 4,670
Liked 3,564 Times in 1,021 Posts
|
|
Nice job on that revolver. I think it came out fine !!!
I had this model 10 bead blasted then reblued. Came out a matte blue.
The model 64 was bead blasted also then the hammer / trigger and screw heads polished.
|
The Following 6 Users Like Post:
|
|
04-19-2024, 06:41 PM
|
|
SWCA Member
|
|
|
Join Date: Aug 2013
Location: RI/ Savannah, GA
Posts: 6,754
Likes: 27,477
Liked 37,916 Times in 4,611 Posts
|
|
Very nice OP. Good job on the grips!. I have the exact same grips that I wore on my duty 15-3. I was going to refinish them, but they have some honest wear from days gone bye. I left them that way and stuck them on a 15-2
__________________
Pete
I ain't no fortunate son
|
The Following User Likes This Post:
|
|
04-19-2024, 07:33 PM
|
|
Member
|
|
|
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,721
Likes: 247
Liked 29,291 Times in 14,151 Posts
|
|
Most of the time and expense of a typical gun refinish is he result of hand polishing prior to hot bluing. The process is far simpler if bead blasting the gun's surface replaces the tedious hand polishing. The bluing operation itself is the easiest part of the job. Bead blasting takes very little time, can be done by almost anyone, and provides a pleasing matte finish similar to what is seen on postwar S&W revolvers from the factory.
|
04-19-2024, 07:38 PM
|
Member
|
|
|
Join Date: Aug 2003
Location: Occupied California
Posts: 2,799
Likes: 1,537
Liked 5,601 Times in 1,619 Posts
|
|
It looks great and they didn't mess up the fit of the sideplate, often the sign of a poor refinish. They must have done the bead blasting with the sideplate attached, they knew what they were doing.
|
The Following User Likes This Post:
|
|
04-19-2024, 08:36 PM
|
Member
|
|
|
Join Date: Jun 2014
Location: Auburn, AL
Posts: 48
Likes: 3
Liked 287 Times in 30 Posts
|
|
Thanks all - I'm happy with it!
The grips were stripped with lacquer thinner, cleaned up, and then had about 10 coats of real spar wiping varnish applied.
|
The Following User Likes This Post:
|
|
04-20-2024, 12:56 AM
|
|
Member
|
|
|
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,721
Likes: 247
Liked 29,291 Times in 14,151 Posts
|
|
Quote:
Originally Posted by Walter Rego
It looks great and they didn't mess up the fit of the sideplate, often the sign of a poor refinish. They must have done the bead blasting with the sideplate attached, they knew what they were doing.
|
Probably. You can bead blast the frame with the side plate and side plate screws in place. I have done that. Just blue the screws afterward along with everything else.
Instead of bluing, you can also use the spray and bake finishes after bead blasting. I have done many guns that way.
|
04-20-2024, 03:52 AM
|
SWCA Member
|
|
|
Join Date: Feb 2006
Location: Pikeville, Tennessee
Posts: 6,109
Likes: 931
Liked 10,034 Times in 3,688 Posts
|
|
I'll tell you what!
Your shop's satin blue is VASTLY superior to S&W's---theirs of the late 40's early-mid 50's---which is the latest I know anything about.
That said, given it was bead blasted, my knee-jerk reaction is it must have been done with very fine beads. I had a Master Grade conversion done on a Colt Government Model by Wilson Combat. Both the slide and frame were bead blasted, and then blued (the slide)---and plated (the frame)----nickel/cadmium(?)---some white metal. The result was an absolutely FLAT finish (reflecting no light at all). My reaction upon seeing yours was it's the shiniest bead blasted finish I've ever seen----and looks GOOD!!
Ralph Tremaine
|
04-20-2024, 09:50 AM
|
|
Member
|
|
|
Join Date: Sep 2009
Location: Hillsdale, Mi.
Posts: 7,510
Likes: 7,057
Liked 7,099 Times in 2,950 Posts
|
|
Looks pretty darn good for a shooter!!! Bob
|
04-20-2024, 10:31 AM
|
SWCA Member
|
|
|
Join Date: Dec 2020
Location: South Carolina upstate
Posts: 1,599
Likes: 2,329
Liked 3,026 Times in 1,091 Posts
|
|
Nice pistol! Very nice work on the grips.
__________________
Kind regards, Heinz
|
04-20-2024, 10:32 AM
|
Member
|
|
|
Join Date: Feb 2013
Location: Columbus, OH
Posts: 206
Likes: 228
Liked 356 Times in 83 Posts
|
|
Looks great! Happy to see a fine model 19 not left to waste away
|
04-20-2024, 11:33 AM
|
Member
|
|
|
Join Date: Jun 2014
Location: Auburn, AL
Posts: 48
Likes: 3
Liked 287 Times in 30 Posts
|
|
I'm going to call the shop on Monday to get more details on the process they used. I should have asked more when I picked it up, but I was running on limited time.
My guess is that they bead blasted the whole gun, then worked a series of polishing wheels over the flats and other areas, most likely finishing with Scotch Brite wheels to give the satin finish. They're definitely satin - not high polished, nor matte like bead blasted.
|
The Following 3 Users Like Post:
|
|
04-20-2024, 11:44 AM
|
SWCA Member
|
|
|
Join Date: Jul 2005
Location: Indiana
Posts: 11,972
Likes: 10,173
Liked 10,162 Times in 4,818 Posts
|
|
Looks like good, careful work by someone who understood what an S&W revolver should look like. Nice job, from what I see. I too would be much happier with the revolver after refinishing.
|
04-20-2024, 12:15 PM
|
SWCA Member
|
|
|
Join Date: Feb 2003
Location: Michigan
Posts: 7,881
Likes: 11,880
Liked 13,882 Times in 3,369 Posts
|
|
Yes. 100% better.
|
04-20-2024, 05:37 PM
|
|
Member
|
|
|
Join Date: Jun 2018
Location: West Virginia
Posts: 2,028
Likes: 1,642
Liked 2,896 Times in 1,172 Posts
|
|
Beautiful work! Very nice restoration.
__________________
Heavily armed old man.
|
|
Posting Rules
|
|
|
|
|