|
|
04-08-2012, 12:14 AM
|
Member
|
|
|
Join Date: Jan 2009
Location: Arizona
Posts: 422
Likes: 6
Liked 46 Times in 35 Posts
|
|
442 endshake
My 442 is in Connecticut on its way to Springfield. What do you think S&W will do for the endshake? How will they fix it? Thanks.
|
04-08-2012, 08:33 AM
|
Banned
|
|
|
Join Date: Nov 2001
Location: Se. Pa.
Posts: 1,330
Likes: 67
Liked 81 Times in 50 Posts
|
|
New yoke or repair it??
|
04-08-2012, 10:28 AM
|
|
Member
|
|
|
Join Date: Mar 2003
Location: North Texas
Posts: 426
Likes: 11
Liked 392 Times in 90 Posts
|
|
The fix could be as easy as installing a shim. If the endshake is really bad, stretching the yoke or replacing it is a bit more involved. S&W's specs for acceptable endshake is a bit more liberal than it used to be in the old days. How bad was it? Did you measure the endshake before you sent it in?
|
The Following User Likes This Post:
|
|
04-08-2012, 09:23 PM
|
Member
|
|
|
Join Date: Jan 2009
Location: Arizona
Posts: 422
Likes: 6
Liked 46 Times in 35 Posts
|
|
I have no idea how much endshake the 442 has. Maybe they willcheck it and say that it is within their specs. If they use a shim, is that adding a part that the gun never had before? That just sounds a bit HOKEY.
|
04-08-2012, 10:18 PM
|
Banned
|
|
|
Join Date: Nov 2001
Location: Se. Pa.
Posts: 1,330
Likes: 67
Liked 81 Times in 50 Posts
|
|
Quote:
Originally Posted by Robert B
I have no idea how much endshake the 442 has. Maybe they willcheck it and say that it is within their specs. If they use a shim, is that adding a part that the gun never had before? That just sounds a bit HOKEY.
|
They wont be adding any shims.
|
04-09-2012, 11:01 AM
|
Member
|
|
|
Join Date: May 2006
Location: Arizona
Posts: 151
Likes: 0
Liked 12 Times in 5 Posts
|
|
My first 442-1 was having misfires and went back to S&W for end shake. The yoke was replaced and it was fine afterwards.
|
04-09-2012, 08:09 PM
|
Member
|
|
|
Join Date: Jan 2009
Location: Arizona
Posts: 422
Likes: 6
Liked 46 Times in 35 Posts
|
|
Thanks for all of your replies. I am glad that the fix won't be to add a part that was not on the original parts list (shim). Maybe they will just send it back to me and say that the endshake is not excessive. I am ok with whatever they do if they have to fix it. I love that little revolver! Hard to believe that it is as effective as it is being so small. I know that the 135+P Golddots are street proven though. It's great for having it on me when just lounging around the house or when I need it for deep concealment. Sometimes you just don't want to put on the thick gun belt. Thanks again for your replies.
|
04-09-2012, 10:37 PM
|
Member
|
|
|
Join Date: Apr 2005
Posts: 125
Likes: 2
Liked 30 Times in 11 Posts
|
|
They put the barrel end of the yoke (the part the ejector rod and center pin passes through that bears on the inside of the cylinder) over a metal rod and tap it with a hammer to stretch it, then they square the end off and check the bc gap, and repeat as needed. This is what was explained to me by a Smith smith.
Last edited by arc2x4; 04-09-2012 at 10:42 PM.
|
04-10-2012, 02:40 AM
|
Member
|
|
|
Join Date: Jan 2009
Location: Arizona
Posts: 422
Likes: 6
Liked 46 Times in 35 Posts
|
|
Does S&W stretch yokes to get endshake down when they build brand new guns?
|
04-10-2012, 05:07 AM
|
|
Member
|
|
|
Join Date: Jan 2009
Location: Knoxville, TN
Posts: 395
Likes: 75
Liked 87 Times in 29 Posts
|
|
I had this done by a local gunsmith and he did the same thing S&W was going to do. However, instead of hitting it with a hammer, he had a thing that looked a little bit like a tubing cutter without the sharp cutting piece...he spun it around the yoke over and over and he would tighten it a little bit as he went. Same effect as hitting the yoke with a hammer, but a little more controlled. I wonder if S&W would have the same device to do this job? B
|
04-10-2012, 05:09 AM
|
|
Member
|
|
|
Join Date: Jan 2009
Location: Knoxville, TN
Posts: 395
Likes: 75
Liked 87 Times in 29 Posts
|
|
Quote:
Originally Posted by Robert B
Does S&W stretch yokes to get endshake down when they build brand new guns?
|
I imagine they just cut that part to the right length and insert it in the gun. This is the result of shooting the gun and is not uncommon. It would normally take quite a while to get endshake unless you're using a lot of hot loads. The gun I had done was an older model 13 that had been around for a few years. Came back from the gunsmith tighter than a drum and works great. Best wishes, B
|
07-22-2018, 07:20 PM
|
Member
|
|
|
Join Date: Jul 2018
Location: Florida
Posts: 11
Likes: 5
Liked 1 Time in 1 Post
|
|
They dont stretch them during manufacturing! There just over sized and the face reemed to spec.
|
07-23-2018, 06:18 AM
|
Member
|
|
|
Join Date: Mar 2009
Location: NC
Posts: 181
Likes: 243
Liked 67 Times in 44 Posts
|
|
Six years old?
__________________
Chewy
|
The Following User Likes This Post:
|
|
|
Posting Rules
|
|
|
|
|
All times are GMT -4. The time now is 03:36 AM.