|
|
03-16-2013, 01:51 PM
|
Member
|
|
|
Join Date: Mar 2013
Posts: 10
Likes: 4
Liked 0 Times in 0 Posts
|
|
Model 29 rear factory sight
I am wanting to order the rear sight for my 29 with a 6 inch barrel.
located four part numbers based on barrel size i assume from MidwayUSA.
However when i contacted them they advised i contact a gunsmith for the correct size.
Wondering if from your order history or knowledge if anyone has the part number for mine?
Thanks
|
03-16-2013, 04:00 PM
|
|
SWCA Member
|
|
|
Join Date: Feb 2013
Location: Oklahoma City, OK
Posts: 1,351
Likes: 174
Liked 1,426 Times in 415 Posts
|
|
do you need the entire assemby or just a replacement blade?
do a search for my post on new model vs old model. I needed a replacement rear sight as well for my 29. unless you have a 1993 and later gun with the shorter round end leaf, you're going to have to do some searching. Midway just has new model rear sights. as for height, i cannot speak to which the 6" barrel had but my 8 3/8" barrel left the factory with a .146" rear blade.
|
03-16-2013, 06:39 PM
|
Member
|
|
|
Join Date: Mar 2013
Posts: 10
Likes: 4
Liked 0 Times in 0 Posts
|
|
Thank you for the reply, I need the assembly as my 29 had optics installed when i purchased it.
Is a 1993 so i should be ok with Midways assembly if i can find a part number related to barrel length.
The 29 came in 4",6",6 1/2",8 3/8 and 10 5/8 barrel lengths as you probably know.
.146 came on your 8 3/8 model, narrows it down a little more.
Listed sizes are,
.086
.136
.146
.160
.196
|
03-16-2013, 06:56 PM
|
|
SWCA Member
|
|
|
Join Date: Feb 2013
Location: Oklahoma City, OK
Posts: 1,351
Likes: 174
Liked 1,426 Times in 415 Posts
|
|
i would go with the .136" or .146". your only talking about 1/100" so it will be like getting used to shoot any new gun.
|
03-16-2013, 07:51 PM
|
|
US Veteran
|
|
|
Join Date: Jun 2006
Location: NW Florida
Posts: 638
Likes: 647
Liked 483 Times in 146 Posts
|
|
I had a 6" 629 with the longer square forward end sight it took the .146.
|
The Following User Likes This Post:
|
|
03-17-2013, 08:41 AM
|
Member
|
|
|
Join Date: Mar 2009
Location: middle tennessee
Posts: 104
Likes: 0
Liked 11 Times in 7 Posts
|
|
It might be cheaper just calling up S&W and ordering the factory part from them.
|
The Following User Likes This Post:
|
|
03-17-2013, 12:31 PM
|
Member
|
|
|
Join Date: Mar 2013
Posts: 10
Likes: 4
Liked 0 Times in 0 Posts
|
|
Quote:
Originally Posted by stu1ritter
|
Good find, thank you very much!
Looks like .146 it is.
|
03-17-2013, 12:37 PM
|
SWCA Member
|
|
|
Join Date: Aug 2005
Posts: 7,916
Likes: 3,523
Liked 6,744 Times in 2,626 Posts
|
|
Quote:
Originally Posted by IPman
I am wanting to order the rear sight for my 29 with a 6 inch barrel.
located four part numbers based on barrel size i assume from MidwayUSA.
However when i contacted them they advised i contact a gunsmith for the correct size.
Wondering if from your order history or knowledge if anyone has the part number for mine?
Thanks
|
See chart below.
|
The Following User Likes This Post:
|
|
03-17-2013, 10:44 PM
|
|
SWCA Member
|
|
|
Join Date: Feb 2013
Location: Oklahoma City, OK
Posts: 1,351
Likes: 174
Liked 1,426 Times in 415 Posts
|
|
Quote:
Originally Posted by kwikrnu
It might be cheaper just calling up S&W and ordering the factory part from them.
|
they have very limited supply of old style rear sight assemblys. I just ordered one from them and had to order the .160" because the only assembly they had "old style" had that blade on it. Now they were more than happy to also sell me a seperate .146" blade. Since all the blades are the same, new vs old, I chose to just get one from another less costly supplier.
|
03-17-2013, 10:50 PM
|
|
SWCA Member
|
|
|
Join Date: Feb 2013
Location: Oklahoma City, OK
Posts: 1,351
Likes: 174
Liked 1,426 Times in 415 Posts
|
|
Quote:
Originally Posted by stu1ritter
|
I'm not so sure. Jeff at S&W last week told me that my M29 8.375" left the factory with a .146" blade height. The web site says .160". Unless proven otherwise I am going to take the manufacturers word for it. Still a great resource however.
|
03-18-2013, 01:52 PM
|
Member
|
|
|
Join Date: Mar 2013
Posts: 10
Likes: 4
Liked 0 Times in 0 Posts
|
|
Quote:
Originally Posted by flundertaker
I'm not so sure. Jeff at S&W last week told me that my M29 8.375" left the factory with a .146" blade height. The web site says .160". Unless proven otherwise I am going to take the manufacturers word for it. Still a great resource however.
|
Sure, just as i figured out i was ordering the .146 lol
|
|
Posting Rules
|
|
|
|
|