|
|
04-09-2024, 12:22 PM
|
Member
|
|
|
Join Date: Aug 2014
Location: Lexington,SC
Posts: 197
Likes: 12
Liked 367 Times in 117 Posts
|
|
Scratches on stainless handgun
Which type of Scotch Guard pads can I use to remove these scratches? Appreciate your help.
|
The Following User Likes This Post:
|
|
04-09-2024, 12:36 PM
|
Member
|
|
|
Join Date: Sep 2018
Posts: 1,901
Likes: 2,298
Liked 2,990 Times in 1,115 Posts
|
|
I'm using 3M General Purpose Super Fine, which is gray in color.
It matters how and which direction you stroke, so proceed lightly and carefully until you catch on. Works really well...
__________________
Uvidíme se později, aligátore.
|
The Following 2 Users Like Post:
|
|
04-09-2024, 02:24 PM
|
|
Member
|
|
|
Join Date: Apr 2006
Posts: 17,928
Likes: 7,917
Liked 26,044 Times in 8,778 Posts
|
|
I use the very fine gray 3M pads as well and they work very well for a final finish. If you have deeper scratches that the 3m pads won't take out, use sandpaper first. I'd start with 320 grit first and adjust up or down accordingly. When the scratches are gone, then use the 3M pad for the final finish. Of course when refinishing a gun, ALWAYS go with the grain iof the metal.
I also remove the cylinder and grips first - make it much easier to work on. If extensive sanding is required then I disassemble the entire gun - it will be cleaned and properly lubed before reassembly. You don't want sanding dust and grit inside!
Last edited by chief38; 04-09-2024 at 02:26 PM.
|
04-09-2024, 03:31 PM
|
|
US Veteran
|
|
|
Join Date: Feb 2013
Location: Dallas, Texas
Posts: 8,322
Likes: 2,555
Liked 13,346 Times in 4,613 Posts
|
|
Scratches tell a story about long use. I like these scratches.
__________________
Come and take it!!
|
The Following 4 Users Like Post:
|
|
04-09-2024, 09:34 PM
|
|
Member
|
|
|
Join Date: Apr 2011
Location: Twin Cites, Minnesota
Posts: 5,168
Likes: 11,039
Liked 10,917 Times in 3,290 Posts
|
|
Quote:
Originally Posted by chief38
... Of course when refinishing a gun, ALWAYS go with the grain iof the metal.
...
|
Grain? What grain? How does one detect the direction of any grain?
|
04-09-2024, 09:59 PM
|
Member
|
|
|
Join Date: Oct 2002
Location: Indiana USA
Posts: 1,150
Likes: 3
Liked 207 Times in 109 Posts
|
|
You want to go lengthwise of the barrel, cylinder and the frame, not crosswise. Think long direction rather than short. If you have to resort to wet or dry paper for scratches that Scotch-brite won't remove be sure to use a sanding block, I use WD-40 to lubricate the wet or dry paper. I use an Art gum eraser as a sanding block,when done with the wet or dry polishing and are satisfied the deeper scratches have been removed then you can use the grey Scotch-brite. For final finish I use a dab of Simichrome or Flitz on the Scotch-brite. Wipe off with a microfiber cloth and wax with Ren wax polishing with microfiber cloth.
Last edited by Marksman; 04-09-2024 at 10:01 PM.
|
04-09-2024, 10:06 PM
|
Member
|
|
|
Join Date: Oct 2002
Location: Indiana USA
Posts: 1,150
Likes: 3
Liked 207 Times in 109 Posts
|
|
To touch up scratches or wear on the sandblasted receiver/barrel top take a small piece of 240 grit paper and tap with a small brass rod or hammer. A woodpecker like tapping is what will blend the sandblast finished surfaces.
|
The Following User Likes This Post:
|
|
04-09-2024, 10:26 PM
|
Member
|
|
|
Join Date: Nov 2012
Posts: 596
Likes: 1,544
Liked 1,401 Times in 292 Posts
|
|
Would a Scotch Brite pad work on the cylinder turn ring?
|
04-10-2024, 07:20 AM
|
Member
|
|
|
Join Date: Apr 2007
Location: Virginia
Posts: 8,845
Likes: 19,839
Liked 12,007 Times in 5,444 Posts
|
|
You can remove the cylinder turn line with a Scotchbrite pad, but as soon as you close the cylinder and pull the trigger, the turn line will begin again. Even from the factory, there is at least a faint turn line as the action must be cycled during the fitting process and test firing.
__________________
VCDL, GOA, NRA
|
The Following 3 Users Like Post:
|
|
04-18-2024, 11:17 PM
|
|
Member
|
|
|
Join Date: Nov 2013
Location: Minnesota
Posts: 219
Likes: 59
Liked 152 Times in 66 Posts
|
|
I also use gray and green scotch-brite pads but keep them wet with oil while working the pads. The oil seems to smooth out the lines from the pads.
|
The Following 2 Users Like Post:
|
|
04-18-2024, 11:20 PM
|
|
Member
|
|
|
Join Date: Oct 2005
Location: Central PA.
Posts: 1,099
Likes: 982
Liked 761 Times in 238 Posts
|
|
Quote:
Originally Posted by ISCS Yoda
Scratches tell a story about long use. I like these scratches.
|
This.
I live with the scratches and wear.
Last edited by Malysh; 04-20-2024 at 03:29 PM.
|
The Following 2 Users Like Post:
|
|
04-19-2024, 03:01 PM
|
|
Member
|
|
|
Join Date: Jun 2005
Location: South Florida
Posts: 375
Likes: 69
Liked 364 Times in 126 Posts
|
|
Since "gun scratching gnomes" are at work multiplying scratches in my safe I decided to leave the scratches as battle scars.
|
|
Posting Rules
|
|
|
|
|