|
|
03-26-2024, 09:34 PM
|
Member
|
|
|
Join Date: Mar 2024
Location: Kentucky
Posts: 2
Likes: 1
Liked 0 Times in 0 Posts
|
|
Model 10 receiver damage
Long time listener, first time caller. Recently I acquired a model 10-14, the previous owner shot a squid load and unknowingly fired another load behind it. The squid was lodged in the barrel resulting in catastrophic failure. Long story short it split he barrel but after removal of the barrel is has also split the bottom of the threaded portion on the frame. how hard is it to acquire a "stripped" frame/receiver? I know I've found quite a bit of barrels. But no luck on a frame. If they're unobtainable is it possible to ship the handgun to S&W directly for repair? I'm not expecting this to be covered by warranty, I'm very willing to pay for repair. Any help/guidance would be greatly appreciated.
Edit: Can upload pictures if it helps.
|
03-26-2024, 10:18 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,225
Likes: 484
Liked 11,391 Times in 3,522 Posts
|
|
Welcome to the forum.....
Not an unusual outcome after a "squib" load. These accidents can damage the barrel and the barrel lug in the frame. Fortunately, there were no injuries.
Best course would be to call Smith and Wesson to see what they can do. 1-800-331-0852
The frame will have to be replaced.
The other option would be to part out the internals and purchase a new revolver.
Carter
__________________
Ret. LE, FA Instr, S&W Armorer
Last edited by armorer951; 03-26-2024 at 10:19 PM.
|
The Following 3 Users Like Post:
|
|
03-26-2024, 10:42 PM
|
Member
|
|
|
Join Date: Nov 2023
Location: Eastern Tennessee
Posts: 35
Likes: 127
Liked 44 Times in 17 Posts
|
|
Quote:
Originally Posted by armorer951
Not an unusual outcome after a "squib" load. These accidents can damage the barrel and the barrel lug in the frame.
Carter
|
Pardon a slight thread deviation….A question for Carter: No doubt this significant damage was because the normal round hit the squibbed bullet obstruction in the barrel.
I’m looking for a warm fuzzy that a squib round by itself wouldn’t cause damage: I had a first ever-squib last weekend. Luckily I recognized it immediately; kept the muzzle down range and counted to ten before dumping the rounds. At home I tapped out the bullet with a wood dowel and a plastic hammer. The bore seems unaffected by my inexperienced eyes.
My plan is to assume I was luckier than the OP, that all is good, and the revolver can continue to get exercised as usual.
Thoughts welcome.
__________________
Tim
|
03-26-2024, 10:45 PM
|
Member
|
|
|
Join Date: Mar 2024
Location: Kentucky
Posts: 2
Likes: 1
Liked 0 Times in 0 Posts
|
|
Thank you much, gentlemen. Previous owner learned a valuable less about buying someone else's handloads.
|
03-26-2024, 11:08 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: Evansville, Indiana USA
Posts: 6,225
Likes: 484
Liked 11,391 Times in 3,522 Posts
|
|
2700.....
My apologies. I should have said that the scenario described in the OP can, and usually does, cause the damage described. Sometimes significant damage and personal injury are the result.
Squib loads like you describe, which result in an under-powered projectile getting stuck in the barrel are usually easy to deal with, in pistols and revolvers at least. They are cleared just the way you described, and are usually do not result in damage.
Sounds like you took care of the problem successfully. Thankfully, likely no damage.
Carter
__________________
Ret. LE, FA Instr, S&W Armorer
Last edited by armorer951; 03-26-2024 at 11:27 PM.
|
The Following 2 Users Like Post:
|
|
03-26-2024, 11:40 PM
|
Member
|
|
|
Join Date: May 2013
Location: Denver area
Posts: 6,252
Likes: 20,294
Liked 13,121 Times in 4,179 Posts
|
|
As a general proposition, the squib does no harm to the gun by itself. It’s the subsequent round(s) that causes the damage.
If you detect a punny report, STOP PULLING THE TRIGGER!
|
The Following 3 Users Like Post:
|
|
|
Posting Rules
|
|
|
|
|
All times are GMT -4. The time now is 01:05 PM.