|
|
05-08-2024, 02:51 PM
|
|
SWCA Member
|
|
|
Join Date: Apr 2009
Location: Salmon, Idaho
Posts: 2,822
Likes: 4,217
Liked 9,784 Times in 1,495 Posts
|
|
Side plate on nickel 29-2 does not fit flush.....suggestions?
I purchased a 29-2 that for some reason has an issue where the side plate is not seating fully....near the grip frame where it meets the top of the frame.
You can see it's raised slightly in that area.
Yes, I have tried gently tapping it with a plastic mallet and tightening the screws.
I believe this to be a QC issue from the factory as it was made in the mid to late 1970's when QC was a bit lacking.
Suggestions??
__________________
Tom Graham SWCA #2303
|
05-08-2024, 02:56 PM
|
Member
|
|
|
Join Date: Nov 2022
Location: Arizona
Posts: 1,564
Likes: 83
Liked 5,524 Times in 1,272 Posts
|
|
No photo.
Without looking at it it could well be something under the sideplate isn't properly seated and keeping the sideplate from fitting flush. Don't tap it any more before having the plate removed and inspecting the lockwork.
|
The Following 2 Users Like Post:
|
|
05-08-2024, 03:07 PM
|
|
SWCA Member
|
|
|
Join Date: Apr 2009
Location: Salmon, Idaho
Posts: 2,822
Likes: 4,217
Liked 9,784 Times in 1,495 Posts
|
|
I removed the side plate a few minutes ago and I see some rough raised edges on the under side of the side plate doesn’t look like it was trimmed off properly. I’m going to use a fine file to remove the burrs/extra material and try it again again.
Sure seems like a factory quality issue that got missed. I will report back.
__________________
Tom Graham SWCA #2303
|
The Following 3 Users Like Post:
|
|
05-08-2024, 05:14 PM
|
SWCA Member
|
|
|
Join Date: Apr 2013
Location: Colorado springs
Posts: 274
Likes: 273
Liked 285 Times in 121 Posts
|
|
Make sure all the internals are properly seated, especially the hammer block safety.
|
The Following 3 Users Like Post:
|
|
05-09-2024, 02:13 AM
|
|
Member
|
|
|
Join Date: May 2009
Location: South Florida
Posts: 7,585
Likes: 2,512
Liked 8,367 Times in 2,949 Posts
|
|
Did you purchase it new with this issue in the 70's?
If you purchased it used Did it have the issue when you bought it or did it develop after you removed the sideplate?
Without pics it's all just guessing,
|
05-09-2024, 08:06 AM
|
Member
|
|
|
Join Date: Apr 2007
Location: Virginia
Posts: 8,858
Likes: 19,879
Liked 12,019 Times in 5,449 Posts
|
|
If this is a new issue, then there is something wrong under the side plate. Could be something not properly aligned or some debris. If this revolver has always had this issue with the side plate fit, then it could be a case of sloppy fitting at S&W or it is not the original side plate, but was replaced at some point.
__________________
VCDL, GOA, NRA
|
05-09-2024, 09:33 AM
|
|
US Veteran
|
|
|
Join Date: Nov 2009
Location: Michigan Western UP
Posts: 12,371
Likes: 3,065
Liked 14,467 Times in 5,504 Posts
|
|
I am much more accustomed with working on Pre-WWII guns, but had purchased a S&W Target that had a sideplate that would not sit all the way down into the frame. It turned out to be a hammer stud that had loosened and slightly unscrewed from the frame. Fashioned a spanner tool and tightened it - problem solved. Back then, all studs were threaded and so a chance any of them could have been the problem.
__________________
Gary
SWCA 2515
|
The Following 2 Users Like Post:
|
|
05-09-2024, 11:09 AM
|
|
US Veteran
|
|
|
Join Date: Feb 2016
Location: western NC
Posts: 3,085
Likes: 2,565
Liked 6,950 Times in 2,174 Posts
|
|
Has it been refinished?
|
05-09-2024, 11:17 AM
|
|
SWCA Member
|
|
|
Join Date: Apr 2009
Location: Salmon, Idaho
Posts: 2,822
Likes: 4,217
Liked 9,784 Times in 1,495 Posts
|
|
All is well
I filed off the high spots that got missed by the factory and the side plate is flush
No it has not been refinished just poorly fitted at the factory
__________________
Tom Graham SWCA #2303
|
The Following 8 Users Like Post:
|
|
05-13-2024, 10:40 PM
|
|
Member
|
|
|
Join Date: Nov 2004
Location: Mountain State
Posts: 3,601
Likes: 97
Liked 387 Times in 155 Posts
|
|
Quote:
Originally Posted by THREEDFLYER
I purchased a 29-2 that for some reason has an issue where the side plate is not seating fully....near the grip frame where it meets the top of the frame.
You can see it's raised slightly in that area.
Yes, I have tried gently tapping it with a plastic mallet and tightening the screws.
I believe this to be a QC issue from the factory as it was made in the mid to late 1970's when QC was a bit lacking.
Suggestions??
|
The side plate was pried off and bent it. Unlesss you know what you are doing to fix it ? You will screw it up more. Good luck
|
05-13-2024, 10:48 PM
|
Member
|
|
|
Join Date: Nov 2022
Location: Arizona
Posts: 1,564
Likes: 83
Liked 5,524 Times in 1,272 Posts
|
|
When removing or reinstalling a side plate…instead of a plastic mallet you should use a lead babbitt bar. They’re softer than the steel in the gun and are far less likely to cause unintentional damage.
|
|
Posting Rules
|
|
|
|
|