Search results

I realize it's just reaming out the cylinder, a little bit more to accept the longer cartridge. I have a model 30 -1. It is not a museum piece nor a collector's item. So I was considering having this done to the cylinder, just to give it more versatility. What would be the average cost of such a...

Flat latch, pinned barrel, diamond grips. Sn# 731XXX. The finish is a bit worn to say the least. But it's mechanically very sound; timing, lockup, end shake all of that good stuff. When might have this been made?

I'm not sure if this is the right section. Please move if not. I'm considering buying a flat latch model 30-1 and I'd like to change out the cylinder release latch to something a little more standard. How simple or difficult is that?If it isn't even possible?

The K frame Gods have smiled upon me. 10-8 and 64-3. The pachmayr grips on the 64 is missing a grip screw bushing so the end of the grip screw pokes out on the other side a bit. 10-8 was an Atlanta P.D. gun, the 64 was a Ga. DOC gun.

***Sold*** 431PD .32 H&R magnum with crimson trace laser grips. It's a shooter not a looker. $550 or trade for LCR 327. Fayette or Coweta counties Georgia.

well maintained 642 with plastic box, no built in lock. WTT in eastern Alabama (near Auburn) for a Beretta model 81(?) .32 acp.

I looked and looked and cannot find any more Speer 200gr. .44 mag Gold Dot short bbl. this round was my favorite in my 6" mod. 629. loaded light for a .44 mag but still stouter than any .44spl. I sent an e-mail inquiry to Speer but got no reply. anyone know of a substitute?

the X frame last I looked, was only made to fit with the N frame round butt design. has S&W made them for the N frame square butt yet?

Traded....

so tomorrow I am going to buy a locked 342 PD Ti. I found a local shop that will remove the lock and install a plug so I won't have that concern. This gun being listed at 11 oz. will be a nice drop in pocket option for this time of year when coat pocket carry offers an advantage. Loading this...

I've read a few times of folks doing something to the chambers of their model 30 revolvers so they will chamber the .32 H&R mag. I've seen the H&R mag velocities from a 2" bbl to be in the low 900s and the Buffalo Bore .32 Long rounds to be in the mid to high 800s from the same length bbl. it...

I have a Walther PP 7.65mm. the firing pin has been grinded on for some reason by a previous owner and the decocker does not move in its full rotation down. my question is which new firing pin should I get for a west german made import by interarms? the square or rounded? a youtube video made...

with a 6" bbl in a 629 44 mag, does the full underlug weight of about 3 oz. make that much difference in shooting pleasure compared to the classic or traditional 3/4 underlug? what's your take on it?

S&W model 30 no dash. 3" bbl, .32 S&W Long, factory nickel is about 85%. This is a flat latch “I frame” revolver. I want to trade it for a model 30-1 or model 31 (both are .32 S&W Long) in any bbl length. The reason is this gun is for my daughter and she does not like the flat latch, says its...

I have the opportunity to possibly get a 624 no-dash 4" gun. taper bbl and regular wood grips. I was wondering what the approx. value of the gun would be in good condition without the box? how many of these were made? I think I read some time ago that the dallas p.d. issued this model at one...

no disrespecting national flags, just men playing a man's game. there is balance in the universe once more.

SOLD......

I tried searching and its either not here or buried very well...... fair to good condition, not pinned or recessed, rubber boot grips, model 60 no dash, stamped (not etched or engraved, but stamped) NY-1. can anyone give an approx. value? I have a local offer to trade for a benchmade auto...

I've read a lot of conflicting material on this, seen photos which conflict with each other.... so I will ask the experts. is my model 60 no dash NY-1 fake or real? sn# available via PM for the experts if needed. thanks.

sold.......