Search results

I have a Performance Center 627-8 shot. Stain screw will not budge. Does the PC Red Lock tight this screw?

I have marks on the back of my 5906 slide from the levers during reassembly. Is there a way to touch this area up without bead blasting?

I have a 5906 that I was thinking of sending in to the Performance Center for the action package. Is there services worth it?

Reloading issue with 625, 45 acp. Loading 200 grain SWC. Issue is fit in the cylinder. Can not close cylinder. Bullets will fit in a chamber checker (EGW). I even tighten up the the crimp but still and issue. Any tips will be appreciated.

Looking at S&W Performance Center gunsmithing service. A 3rd generation action job is $165. Has anyone had this service performed. Is it worth the cash? What should I really expect. I did call S&W customer service and the representative was ignorant on the service.

Have 5906 with adjustable sights. The white dot rear are kind of grey and dull. Is there a method to clean up the dots without harming the orginal dots.

I have a 64 that is is shooting 2 inches to the left. Dead nuts accurate and nice action. I did send the revolver back for adjustmets but still the same issue. Is this something I have to live with?

I just a new/used 5906. The pistol is mint, and something told me to buy it. Question: I was looking tat the S&W Peformance center site. S&W offer services called action paackage. Has anyone had this service done? What do they actual mean concerning tuning the action?

I seen a 4506 that caught my eye. Police trade in. Holster wear, etc.The price is at $350.00, no box and one single magazine. Question: 1) Good price? 2) What to look in a used 4506. Lock up, trigger pull, etc. 3) The night sight need replaced. Does S&W carry this?

I had a action job on my 617 from a reliable gunsmith whi is know for his work. In short, I had taken the revolver to the range today to try out. Big difference in the action, etc. Question is in regards to failure to fire rounds. There were 2 (two) failure to fire rounds on the average for...

Question 625 in .45 acp. In the market for a 625 in .45 acp. Have not shot one and where I live in Texas I basically order and pick up. Need comments from the folks with experience so I make the right choice the first time. Basically I looking at three choices. 1) Used 625, 5" 2)...

I have a 617 with a 4” barrel. The revolver has been sighted in so not problems there. What my question is that rear sight blade is not centered in the sight assembly but more to the right of the total travel of windage. Is this normal? All of my other revolvers with adjustable sights are pretty...

Question: 617 action work. I was researching various forums concerning action work on a 617, 10 shot revolver. There is confusing information concerning what should and what can be complete. • S&W states not to modify the action. • Some folks state to install a new Wolff, 13 lb rebound...

Can some one advise how to replace the rebound sping on a 617

I have a fairly new 627 PC 8 shot,(500 rounds thru the revolver)the action binds sometimes when I shoot in double action mode. Sometimes the trigger is stiff/binds in the beginning of the trigger pull then release fast and sometimes at the very end of the trigger pull.(stiff binds then all of a...

Rebuilding sight on my K frame. Need basic steps less and detail hints on the round spring use to hold the elevation screw.

I would like to put on my 627 Performance Center with a 5" barrel, and 617 with a 4" barrel Millet adjustable sight. The problem is that I kind of confused on which sight to order due to the height call out. Any help will be apprecitaed

I seen an internet artical which shows cleaning your revolver with a brass brush. The artical showed pictures of using the brass brush on the crown, ejector, and cylinder. My question is: Would the brass brush effect the finish?

Looking to buy in bulk moon clips for my 627. Any suggestions on who may have this available?

Need to know if anyone has knowledge on both models. Looking to buy but due to location can not handle or see one in person. The S&W is somewhat limited as to what the differences between the models are in realms of addtional features and workmanship that are put into each model.