Search results

What is a Tisas Pistol? Am I the only one who don't know?

On the question of bobbed hammer primer ignition: Would it possible to swap a m49 or 649 hammer in to the m36 to lower profile of the hammer spur hang up? Or even a hammerless type hammer?

Speaks for itself.

So I had my day in the "barrel" as the joke went. I fell victim to the $.99 offer to search a lost associate. Not surprisingly , no results. They then have charged me a further $35 for what I do not know. I have calmly posted thru channels the opt out requests. Education can be expensive...

Looking for larger than issue wood grip.

How Come: I pay 98$ per year for my rural PO secure box, while free loaders using their open air road side mail boxes pay nothing? It cost's the postal service personal compensation for contract rural drivers and other expenses, while I spend my own gas and vehicle depreciation to get to and fro.

NOt at all happy with the over sized case of the 45 Colt cartridge, using todays low pressure powder charges, Red dot, 231, etc. And that I opened a bottle or Aliant Unique dated 1994 suffering low booms and sensitivity to powder position in case, up or down causing pressure spikes at...

I dusted off my Kimber Custom 1911 .45. 200g Ranier SWC copper coated 1.22" COL, CCI 300, 5.3g 231, mixed brass. It ran flawless as I recalled 5 years ago last outing. Accy very acceptable and predictable impact to sights as I call my shots before looking. On reading up I noticed some don't...

Someone with bad labels on his about me page contacted me about a third party with parts to sell. I gathered from reputation he may one to avoid. Thanks for the heads up.

Have there been any reports of serious failures of 22lr cartridges fired in 22 magnum rimfire chambers? Any discussion?

Ruger three screw old model single six flat top appx 1971. Looking for 22lr cylinder.

I like shooting cast bullets in my 30-06's. My hard bullets with copper gas checks have been leaving no lead behind at up to 1850 fps possibly much more. I get near MOA accy out to 100 yds I don't even know what factory jacketed bullets cost anymore, but my home poured come to around .08$...

I like my favored grocery store. The lights are on, the floor is clean, there is room between the isles, and I compliment the managers when I see them. But last visit... after I checked out by card, I saw that I was charged for two bags of cat food rather than one, and the 750ml of designer...

I have a 586 no dash 4". I got it I believe, unfired. The first shot, the cylinder bolt stud broke off with the thumb button screw getting lost. I replaced promptly and no other problems other than poor accy. Yesterday It suffered a experienced case failure which introduced powder fouling...

I examined a new in store Uberti 1873 today. Very impressive at a attractive price < 500$. I was interested to count the clicks from hammer down thru full cock. It is missing the safety notch before half cock. OK, almost no one recommends loading 6 and using the safety click, maybe for good...

I've picked up a steel can, 1 pound of W 540 at original grease pencil price of 6.95$ I believe it to be unopened. With it came a unopened pound of HS-7 at twice the price. The 540 when opened does not smell, does not show reddish dust nor does my finger find any rust within the can. I plan...

Good, Bad, or Ugly: Taylors Uberti 1873 new frame TUNED vs untuned, vs find a custom gun smith for the tune up if needed, vs old frame. Any opinions? Any experience with the dia issue .452, vs .454? But I'm happy as heck with my 45 shield

How does quality control compare between a decades old Uberti and a NIB Taylors for metal feel of rotation and lock work etc?

Just now reading a thread about using " mid range " and then stronger loads in 80's K Frames. Some respondents say good, some say no. I am asking about using full power loads in 586 no dash, non modified. Should I use a similar amount of caution as if loading full power for m 19-2?

A friend has come across this gem from the past Does anyone know what it is? Is there someone in the Portland , Or. area to take it to for research?