|
|
06-03-2015, 09:58 PM
|
Member
|
|
|
Join Date: Jun 2015
Posts: 3
Likes: 0
Liked 1 Time in 1 Post
|
|
slide wont come off
i just got the sd9ve and have put close to 100 rounds through it and go to clean it and the slide wont come off. ive pulled both of the tabs down but the slide will only move like a quarter of an inch forward and stop. I sat and tried for close to an hour and i have no idea whats going on
|
06-03-2015, 10:05 PM
|
|
Member
|
|
|
Join Date: Mar 2015
Location: Hardin County, Kentucky
Posts: 88
Likes: 87
Liked 32 Times in 21 Posts
|
|
First make sure it is unloaded and the magazine is out, it won't come off with a magazine in the gun. Now pull back on the slide about a 1/4 inch at the same time have the slide release tabs pulled down and pull the trigger and push the slide forward. It should come right off.
|
06-03-2015, 10:15 PM
|
Member
|
|
|
Join Date: Jun 2015
Posts: 3
Likes: 0
Liked 1 Time in 1 Post
|
|
its unloaded, the clip, ive been holding the slide back with one hand about a quarter of an inch, and pulled the tabs down, but i have to pull the trigger when i do it? ive looked on multiple places and none say to do that.
|
06-03-2015, 10:20 PM
|
|
Member
|
|
|
Join Date: Mar 2015
Location: Hardin County, Kentucky
Posts: 88
Likes: 87
Liked 32 Times in 21 Posts
|
|
Yes pull the trigger to release the slide. You have to remember to have the slide pulled back with both tabs pulled all the way down simultaneously, then pull the trigger as well. And keep those tabs pulled down through the whole process.
Last edited by earthtone31; 06-03-2015 at 10:22 PM.
|
06-03-2015, 10:24 PM
|
Member
|
|
|
Join Date: Jun 2015
Posts: 3
Likes: 0
Liked 1 Time in 1 Post
|
|
it worked! thank you so much!
|
The Following User Likes This Post:
|
|
06-03-2015, 10:27 PM
|
|
Member
|
|
|
Join Date: Mar 2015
Location: Hardin County, Kentucky
Posts: 88
Likes: 87
Liked 32 Times in 21 Posts
|
|
Your welcome. Its easy once you do it a few times. Seems a little tricky at first though. Just always make sure the gun is unloaded and no magazine is in the gun or a accidental firing can occur very easily.
Last edited by earthtone31; 06-03-2015 at 10:28 PM.
|
06-04-2015, 12:43 AM
|
Member
|
|
|
Join Date: Jun 2015
Posts: 2
Likes: 0
Liked 0 Times in 0 Posts
|
|
I have been having a somewhat similar issue, but I realized that my pistol wouldn't dry fire at all.... so it wouldn't release the slide.
after trying for a while I put an empty mag back in and I could get it to dry fire then dropped out the mag and everything else worked like it was supposed to to pull the slide.
I'm sure this isn't the right way, but its the only way I could get it to dry fire.
anyone else had this issue? its a new 9ve with only about 50 rounds through it.
|
06-04-2015, 09:59 AM
|
|
US Veteran
|
|
|
Join Date: Aug 2013
Location: San Antonio
Posts: 285
Likes: 122
Liked 106 Times in 68 Posts
|
|
Quote:
Originally Posted by shaunb
I have been having a somewhat similar issue, but I realized that my pistol wouldn't dry fire at all.... so it wouldn't release the slide.
after trying for a while I put an empty mag back in and I could get it to dry fire then dropped out the mag and everything else worked like it was supposed to to pull the slide.
I'm sure this isn't the right way, but its the only way I could get it to dry fire.
anyone else had this issue? its a new 9ve with only about 50 rounds through it.
|
Does yours have a magazine disconnect?
Bill
__________________
Remember the Alamo!
|
The Following User Likes This Post:
|
|
06-04-2015, 01:05 PM
|
|
Member
|
|
|
Join Date: Dec 2014
Location: Oklahoma
Posts: 951
Likes: 682
Liked 301 Times in 210 Posts
|
|
Dry fire without magazine?
Quote:
Originally Posted by shaunb
I have been having a somewhat similar issue, but I realized that my pistol wouldn't dry fire at all.... so it wouldn't release the slide.
after trying for a while I put an empty mag back in and I could get it to dry fire then dropped out the mag and everything else worked like it was supposed to to pull the slide.
I'm sure this isn't the right way, but its the only way I could get it to dry fire.
anyone else had this issue? its a new 9ve with only about 50 rounds through it.
|
You must have a California or similar version-Does is also have a pop-up "Loaded" indicator on the top of the slide?
|
The Following User Likes This Post:
|
|
06-04-2015, 10:56 PM
|
Member
|
|
|
Join Date: Jun 2015
Posts: 2
Likes: 0
Liked 0 Times in 0 Posts
|
|
yup, I am in Ca.
Yes it does have the raised indicator when one is in the chamber.
Not sure what the mag disconnect is though.
|
06-05-2015, 01:18 AM
|
|
Member
|
|
|
Join Date: Mar 2015
Location: Hardin County, Kentucky
Posts: 88
Likes: 87
Liked 32 Times in 21 Posts
|
|
If you have the manual to your SD9VE, look on page 26. There you will find the instructions on how to disassemble a SD9VE/SD40VE with a magazine disconnect safety like your gun has properly. I'm sure you can find the pdf version of the manual online possibly S&W website
|
The Following User Likes This Post:
|
|
06-05-2015, 02:30 AM
|
Member
|
|
|
Join Date: Jan 2015
Posts: 339
Likes: 281
Liked 426 Times in 156 Posts
|
|
I find with my Glocks, and the Sigma I once owned, that instead of pulling back on the slide, its easier to press forward with the top edge of the bbl side of the slide snug against the edge of a counter or table at about a 60* angle.
|
06-05-2015, 03:24 AM
|
|
Member
|
|
|
Join Date: Dec 2014
Location: Oklahoma
Posts: 951
Likes: 682
Liked 301 Times in 210 Posts
|
|
Magazine Disconnect
Quote:
Originally Posted by shaunb
yup, I am in Ca.
Yes it does have the raised indicator when one is in the chamber.
Not sure what the mag disconnect is though.
|
If you look through the magazine channel with the slide off you will see a lever that intrudes into that area. It is pushed up when the magazine is in place. If you want to dry fire the gun you will have to have a magazine in place.
If you want to simply examine the sear action you can push the lever down with a soft pen or other item and it will allow the trigger to move the sear.
There are very good instructions in the manual. I bought the CA version even though it is not required in my state because of the added safety features. I also bought a couple of 16 round magazines to speed things up at the range.
|
06-05-2015, 07:56 AM
|
Member
|
|
|
Join Date: Nov 2005
Location: Upstate SC
Posts: 3,451
Likes: 37
Liked 5,436 Times in 1,762 Posts
|
|
Quote:
Originally Posted by thezacriley
its unloaded, the clip, ive been holding the slide back with one hand about a quarter of an inch, and pulled the tabs down, but i have to pull the trigger when i do it? ive looked on multiple places and none say to do that.
|
For future reference, S&W has come up with a groundbreaking innovation that addresses your problem specifically -- the owner's manual:
https://www.smith-wesson.com/wcsstor...07_15_2014.pdf
__________________
Pisgah
|
The Following 2 Users Like Post:
|
|
06-05-2015, 06:20 PM
|
|
Member
|
|
|
Join Date: Dec 2014
Location: Oklahoma
Posts: 951
Likes: 682
Liked 301 Times in 210 Posts
|
|
I previously wrote:
If you want to dry fire the gun you will have to have a magazine in place.
=======
That was out of context. I was thinking of how to observe the trigger bar and sear action with the slide off in the CA model.
In order to do that, just for analysis, (or curiosity) you should have the magazine out and the magazine disconnect lever up. You can push it up with a soft probe or pencil eraser end.
You will also know, from reading the owners manual, you need to push that lever down before removing the slide. [I have not been able to find out why that makes a difference, and queries to S&W come back with "It won't hurt the gun if you don't do that."]
|
06-07-2015, 02:49 AM
|
|
Member
|
|
|
Join Date: Apr 2015
Location: Orygun
Posts: 53
Likes: 47
Liked 133 Times in 29 Posts
|
|
Trying to pull down both sides at once drives me crazy! Other than that I love mine.
|
06-07-2015, 09:48 PM
|
|
Member
|
|
|
Join Date: Dec 2014
Location: Oklahoma
Posts: 951
Likes: 682
Liked 301 Times in 210 Posts
|
|
Removing slide
Quote:
Originally Posted by Hedrin
Trying to pull down both sides at once drives me crazy! Other than that I love mine.
|
I bought a slide stop bar that is, surprisingly, only 1 mm longer. Laser cut. Makes an incredible difference.
|
The Following 2 Users Like Post:
|
|
06-09-2015, 02:00 AM
|
|
Member
|
|
|
Join Date: Apr 2015
Location: Orygun
Posts: 53
Likes: 47
Liked 133 Times in 29 Posts
|
|
Quote:
Originally Posted by ou1954
I bought a slide stop bar that is, surprisingly, only 1 mm longer. Laser cut. Makes an incredible difference.
|
Where might I acquire such a wondrous item?
|
06-09-2015, 05:49 AM
|
|
Member
|
|
|
Join Date: Apr 2015
Posts: 290
Likes: 14
Liked 197 Times in 123 Posts
|
|
amazon or ebay, I bought mine off ebay as shipping was free. What a difference it makes! Easy to install just remember to keep a little tension on the spring so it doesn't go flying out like it did for me! Highly recommend
Norm
|
06-09-2015, 05:50 AM
|
|
Member
|
|
|
Join Date: Apr 2015
Posts: 290
Likes: 14
Liked 197 Times in 123 Posts
|
|
amazon or ebay, I bought mine off ebay as shipping was free. What a difference it makes! Easy to install just remember to keep a little tension on the spring so it doesn't go flying out like it did for me! Highly recommend
Norm
|
06-09-2015, 06:06 AM
|
|
Member
|
|
|
Join Date: Apr 2015
Posts: 290
Likes: 14
Liked 197 Times in 123 Posts
|
|
on ebay, search for Smith & Wesson S&W SD9 VE 9mm Extended Slide Lock Lever ESLL Black
|
06-09-2015, 02:25 PM
|
|
Member
|
|
|
Join Date: Dec 2014
Location: Oklahoma
Posts: 951
Likes: 682
Liked 301 Times in 210 Posts
|
|
Quote:
Originally Posted by Hedrin
Where might I acquire such a wondrous item?
|
NDZ Performance makes absolutely the best one.
203-439-7787 and [email protected].
Extended Slide Lock Lever Stainless Steel.
It's still the same shape as the factory model but that 1 mm made an incredible difference in take down. No more rags, no more bruised fingers, etc.
Precision laser cut, very high quality.
|
06-09-2015, 02:27 PM
|
|
Member
|
|
|
Join Date: Dec 2014
Location: Oklahoma
Posts: 951
Likes: 682
Liked 301 Times in 210 Posts
|
|
I should mention that it comes in black or stainless. I picked stainless and it looks great and works even better than one would think. Just one mm longer!
|
|
Posting Rules
|
|
|
|
|