|
|
02-27-2015, 09:41 PM
|
Member
|
|
|
Join Date: Aug 2014
Posts: 70
Likes: 2
Liked 21 Times in 14 Posts
|
|
Spring upgrade controversy
In the beginning, there was only the Apex Tactical trigger spring kit for the Sigma, and then also for its successors, the SW9/40, SW9/40VE, the SD9/40 & SD9/40VE. Apex insists a lighter sear spring was required for the Sigma, but for the current SD VE line, they claim their spring kit is now designed with the stock sear spring in mind (as in "leave it be").
Then, along came Galloway Precision and designed a very similar-looking trigger spring kit that does come with a lighter sear spring which they insist is a MUST item for their system to function correctly.
Fine and dandy. Umpteen Youtube videos have been made about the how the Apex spring trigger mod improved the feel of their SD VE's. Finding ones for the Galloway upgrade...eh, haven't found any yet.
But, to sear or not to sear is not the only question plaguing heavy-use SD owners who have reported some premature wear on their replacement striker springs.
Other users have questioned the wisdom of replacing the stock striker spring given how important it is to have a working firing pin each and every time if you intend on using the SD VE for home defense or self-defense.
They may have a valid point.
I've decided to replace my plastic guide rod & recoil spring unit with a stainless steel replacement from Galloway as Apex does not offer one. However, about six months ago, I discovered that Wolff springs also sells replacement stainless steel guide rods for the 4" barrel Sigma/SW/SD series, but with the recoil springs sold separately - as in uncaptured.
Wolff offers one other spring weight that Galloway does not. Besides the stock weight of 17#, Wolff sells an 18# spring, along with the 20# and 22# springs that Galloway also sells.
Now, here comes the punchline.
With every recoil spring that Wolff sells which is heavier than the 17# stock weight, they include, for free, a heavier striker spring: something Galloway does not.
Where they agree is in their similar caveats for the lighter 15# spring:
Galloway says "for light loads only" and Wolff says (in big bold letters) "for competition use only - not for duty use."
Also, the reverse is not the case for the 15# spring - that is, Wolff does not send a lighter weight striker spring with it.
On the face of it, it would seem that leaving in the stock striker spring when doing a trigger spring upgrade has some merit to it.
So, before I do anything, I'd like to hear from the membership on the striker spring issue: keep it stock or opt for the lighter spring?
Also, feel free to chime in if you installed Galloway's kit and feel that swapping out the sear spring really is necessary or just a good idea.
One last issue:
Captured spring and guide rod versus uncaptured spring and guide rod?
If there is no downside to using an uncaptured spring - with the possible increased risk of losing it - a big advantage of it is the ability to buy a couple of springs of different weights (with the extra striker springs). The guide rods sell for $25 and the recoil springs sell for $8 (keep in mind that they come with a heavier striker spring, too).
That's $32 vs. $30 for Galloway with the added features of the Wolff more than offsets the extra two bucks.
My take on it is, if you plan on running +P ammo through your SD, I would opt for a heavier recoil spring and matching heavier striker spring. It will make it harder to rack but mitigate the recoil & muzzle flip a lot more.
YOUR THOUGHTS?
Last edited by PeterPocket; 02-27-2015 at 09:47 PM.
Reason: typos
|
02-27-2015, 11:52 PM
|
|
Member
|
|
|
Join Date: Dec 2014
Location: Oklahoma
Posts: 951
Likes: 682
Liked 301 Times in 210 Posts
|
|
Quote:
Originally Posted by PeterPocket
In the beginning, there was only the Apex Tactical trigger spring kit for the Sigma, and then also for its successors, the SW9/40, SW9/40VE, the SD9/40 & SD9/40VE. Apex insists a lighter sear spring was required for the Sigma, but for the current SD VE line, they claim their spring kit is now designed with the stock sear spring in mind (as in "leave it be").
(snip)
So, before I do anything, I'd like to hear from the membership on the striker spring issue: keep it stock or opt for the lighter spring?
YOUR THOUGHTS?
|
If you EVER use a SD model for self defense, any mods you might make would be used against you in court.
Here is an important post about trigger mods. It has a link to a second article. Check it out-
Facts About "Light Trigger Pull Liability"
The above is a link to another post on this forum. It, in turn, contains a link to an article in a legal forum. It says guns, ammo, modifications, and even reloads will be investigated.
If you have an SD simply for target shooting I suppose anything is open, unless, of course, you need to send your gun back to S&W.
Last edited by ou1954; 02-28-2015 at 02:06 AM.
Reason: Add link
|
The Following 2 Users Like Post:
|
|
02-28-2015, 10:35 AM
|
|
Member
|
|
|
Join Date: Feb 2015
Location: Texas
Posts: 162
Likes: 185
Liked 93 Times in 46 Posts
|
|
Now I am second guessing having the apex spring kit and trigger installed in mine yesterday. I paid $81.00 to have it done, and it feels great when I dry fired it. I am planning on trying it out tomorrow, as we are having my birthday party at the shooting range, and we are expecting 40 people with guns.
I truly hope I didnt screw mine up. I will have to pay someone else to put it back together again.
|
02-28-2015, 11:22 AM
|
|
US Veteran
|
|
|
Join Date: Oct 2006
Location: REPUBLIC OF WEST FLORIDA
Posts: 15,230
Likes: 3,020
Liked 3,451 Times in 1,625 Posts
|
|
The trigger mod vs. civil/criminal liability issue has a lot to do with where you live.
Historically, in my area of the deep south, whether or not the shooting was "justified" is the major issue; gun modifications and or ammo used are not.
Each to their own, but reliability is paramount to me and I go along with the leave it "stock" and shoot the hell out of it crowd.
__________________
NULLI SECUNDUS
|
The Following 5 Users Like Post:
|
|
02-28-2015, 11:27 AM
|
Member
|
|
|
Join Date: Aug 2007
Location: Oklahoma
Posts: 8,161
Likes: 3,623
Liked 5,211 Times in 2,174 Posts
|
|
Quote:
Captured spring and guide rod versus uncaptured spring and guide rod?
|
The most important consideration in a recoil spring is to use the flat-wound spring instead of the old-style round piano wire spring, as the flat-wound is more reliable and lasts far longer.
Having used the Sigmas for loaners and trainers for over a decade, I settled on only using the stock recoil spring assemblies, with the superior ISMI flat wound springs. Since I look at the recoil spring each time I clean the gun, I can spot any incipient chipping in the polymer guide rod and simply drop in a new $10 stock assembly.
I have never had one fail in service, and they typically last for many years.
I tried one of the lighter striker springs and found it getting failures to fire on some ammunition; only factory ammo for classes. I stick to stock.
If you care, I am unimpressed by the current frenzy on putting aftermarket parts in every semi-auto, especially if the goal is to compensate for lack of technique and training. I shoot an M&P Pro in IDPA and USPSA Production, and am glad I bought it already set up rather than buying a cheaper gun and then spending the cost of the gun again trying to turn it into a Pro.
__________________
Science plus Art
|
The Following 3 Users Like Post:
|
|
02-28-2015, 02:36 PM
|
|
Member
|
|
|
Join Date: Mar 2010
Location: SW Ohio
Posts: 961
Likes: 222
Liked 351 Times in 214 Posts
|
|
Agree with the above. If someone feels a new pistol needs a lot of mods to make it right for them, then IMO they're buying the wrong pistol.
Where are you buying the stock recoil assembly? It was my understanding S&W won't even sell a lot parts for either the SD or M&P series to armorers, much less the unwashed.
|
The Following 4 Users Like Post:
|
|
02-28-2015, 02:43 PM
|
Member
|
|
|
Join Date: Aug 2007
Location: Oklahoma
Posts: 8,161
Likes: 3,623
Liked 5,211 Times in 2,174 Posts
|
|
Quote:
Where are you buying the stock recoil assembly? It was my understanding S&W won't even sell a lot parts for either the SD or M&P series to armorers, much less the unwashed.
|
Brownells, Midway, and others list several parts for these pistols. They are not all available, and the ones that are go in and out of stock from week to week. I have had no problems getting trigger springs, recoil springs, and striker assemblies. Just put a new striker assembly in my M&P Pro 5"; the tip of the striker chipped after over 30,000 rounds.
__________________
Science plus Art
|
02-28-2015, 05:02 PM
|
|
Member
|
|
|
Join Date: Dec 2014
Location: Oklahoma
Posts: 951
Likes: 682
Liked 301 Times in 210 Posts
|
|
I'm staying with stock except for the barrel stop/takedown lever, where I put in one a mm longer. Makes takedown quick and easy for me.
On a related subject, there have been a lot of posts about putting in a metal guide rod because folks say the plastic one bends. How do you go about observing a bend in that rod?
Thanks-
|
02-28-2015, 05:08 PM
|
|
Member
|
|
|
Join Date: Dec 2014
Location: Oklahoma
Posts: 951
Likes: 682
Liked 301 Times in 210 Posts
|
|
Quote:
Originally Posted by MOONDAWG
The trigger mod vs. civil/criminal liability issue has a lot to do with where you live.
Historically, in my area of the deep south, whether or not the shooting was "justified" is the major issue; gun modifications and or ammo used are not.
Each to their own, but reliability is paramount to me and I go along with the leave it "stock" and shoot the hell out of it crowd.
|
I agree but when I posted that link I had in mind a couple of cases in which the defense was that the gun went off "by accident" and the forensic folks found the shooters had reduced the trigger pull to a couple of pounds.
|
02-28-2015, 09:42 PM
|
Member
|
|
|
Join Date: Dec 2012
Location: PA.
Posts: 607
Likes: 440
Liked 121 Times in 94 Posts
|
|
I returned my striker spring back to stock after installing the apex lighter spring.
I was having miss fires with more than 1 type of ammo, not so with the stock weight spring.
3
|
The Following 2 Users Like Post:
|
|
02-28-2015, 11:33 PM
|
Member
|
|
|
Join Date: Jul 2014
Posts: 287
Likes: 3
Liked 135 Times in 90 Posts
|
|
Quote:
Originally Posted by 3hounds
I returned my striker spring back to stock after installing the apex lighter spring.
I was having miss fires with more than 1 type of ammo, not so with the stock weight spring.
3
|
Same here. I have Apex trigger springs, a Galloway recoil spring, but after having used several aftermarket striker springs, I went back to the original. I have had no issues with it. I had light strikes with the others. This has been true with factory ammo as well as my handloads with CCI primers.
|
The Following 2 Users Like Post:
|
|
03-02-2015, 09:42 AM
|
Member
|
|
|
Join Date: Nov 2014
Posts: 7
Likes: 0
Liked 1 Time in 1 Post
|
|
Did the Apex spring and polymer trigger on my SW40VE. Didn't like it and added lighter sear spring. Got the pull down to around 6lb average with 0 issues. Got the SD9VE and only changes made to it have been swapping polymer trigger over, 18lb stainless guide rod and TruGlo sights.
|
03-16-2015, 12:48 AM
|
Member
|
|
|
Join Date: Aug 2014
Posts: 70
Likes: 2
Liked 21 Times in 14 Posts
|
|
So easy, Godzilla could do it?>
I decided to swap out JUST the trigger spring and leave everytthing else stock. The 8lb pull needs to be lightened because of how worn out my finger gets - thanks to it being injured by a Sig Sauer P250.
A 5.5 lb or 6lb pull would make a noticable difference after a day at the range.
NOW, guess what. The pin holding in the trigger control unit will not budge! I have watched every video on replacing the trigger return spring which begins by removing the pin from left to right and not right to left as many in the videos recommended. No dice.
NOT for me. It did not matter which side I tried to push out the pin. It would not move a millimeter.
As you will see in my annotated photo below, what aree the issues with the pin as wekkl as the issues I was having with the takedown lever.
Now, as per the YouTube instructions, I started off gently, using the slave pin that came with the kit, to try and push the pin out. Then, I took my plastic coated, two-headed hammer to try and lightly tap it through. No deal. I hity it harder. Nothing.
I took out my punch pins and tried the 1/16" on the inside of the pin. No movement. Then, I went up to the 1/8" pin and placed it squarely over the top of the min.
Again, to no avail, either. I did not want to hit it too hard and risj breaking something.
But, it comes out so easily in the videos and I don't know how given what I am about to show you.
Frankly, I don't see how the pin can be taken out with the open hooked end of the trigger spring inside the deep and wide groove located at the middle of the pin. The hooked end of the slide release spring is also in a groove, but a much shallower one.
From what I can see, tapping on the pin is supposed to get the trigger spring hook to jump right up and over the edge of the groove, and then be dragged along the rest of the pin from the edge of the groove to the physical end of the pin.
What am I missing here? It seems like the spring hook needs to be pulled up and over the edge of the groove and onto the surface of the pin itself.
Notice the Trigger spring hooked around the middle of the pin. But, the pin seems to be stuck inside the frame holes. The pulling tension being applied to the pin does not help the situation. I can see how the magazine pin can be bypassed, but not the trigger spring.
It's almost like someone put Loc-tite or Super-Glue on the pin - it is that tightly stuck in the frame.
Well, I'm open to suggestions before I seek out a gunsmith.
|
03-16-2015, 01:00 AM
|
Member
|
|
|
Join Date: Jan 2015
Posts: 339
Likes: 281
Liked 426 Times in 156 Posts
|
|
Quote:
Originally Posted by PeterPocket
I decided to swap out JUST the trigger spring and leave everytthing else stock. The 8lb pull needs to be lightened because of how worn out my finger gets - thanks to it being injured by a Sig Sauer P250.
A 5.5 lb or 6lb pull would make a noticable difference after a day at the range.
NOW, guess what. The pin holding in the trigger control unit will not budge! I have watched every video on replacing the trigger return spring which begins by removing the pin from left to right and not right to left as many in the videos recommended. No dice.
NOT for me. It did not matter which side I tried to push out the pin. It would not move a millimeter.
As you will see in my annotated photo below, what aree the issues with the pin as wekkl as the issues I was having with the takedown lever.
Now, as per the YouTube instructions, I started off gently, using the slave pin that came with the kit, to try and push the pin out. Then, I took my plastic coated, two-headed hammer to try and lightly tap it through. No deal. I hity it harder. Nothing.
I took out my punch pins and tried the 1/16" on the inside of the pin. No movement. Then, I went up to the 1/8" pin and placed it squarely over the top of the min.
Again, to no avail, either. I did not want to hit it too hard and risj breaking something.
But, it comes out so easily in the videos and I don't know how given what I am about to show you.
Frankly, I don't see how the pin can be taken out with the open hooked end of the trigger spring inside the deep and wide groove located at the middle of the pin. The hooked end of the slide release spring is also in a groove, but a much shallower one.
From what I can see, tapping on the pin is supposed to get the trigger spring hook to jump right up and over the edge of the groove, and then be dragged along the rest of the pin from the edge of the groove to the physical end of the pin.
What am I missing here? It seems like the spring hook needs to be pulled up and over the edge of the groove and onto the surface of the pin itself.
Notice the Trigger spring hooked around the middle of the pin. But, the pin seems to be stuck inside the frame holes. The pulling tension being applied to the pin does not help the situation. I can see how the magazine pin can be bypassed, but not the trigger spring.
It's almost like someone put Loc-tite or Super-Glue on the pin - it is that tightly stuck in the frame.
Well, I'm open to suggestions before I seek out a gunsmith.
|
Having been a past owner of Sigma, I can offer some sage wisdom and advice. I had several issues with mine. I will say the trigger was not the best. The loctite like coating on those pins is there for 2 reasons: to secure the pins, and to provide an anti-tamper indicator to the factory if you modify the trigger, and then send it in on warranty. I was told this by a gunsmith.
If you really want to spend the money for a better trigger, better spring/rod assembly, you may be better off keeping your money, selling the Sigma, and buying a M&P platform, which has a better trigger, etc, and is a much better pistol, IMO.
Just my 2 cents.
|
03-16-2015, 01:17 AM
|
|
Member
|
|
|
Join Date: Dec 2014
Location: Oklahoma
Posts: 951
Likes: 682
Liked 301 Times in 210 Posts
|
|
I don't modify my guns but do have to deal with stubborn old car parts.
If you are not concerned about beauty, consider rotating the pin by grabbing it at an unimportant place with some high quality needle nose pliers. Sometimes you can wrap a place with masking tape and save the surface while still getting a good grip.
Alternatively, there are several solvents for locktite, and you might find one that doesn't affect the polymer frame. I came across one when dealing with MB hydraulic cylinders but would have to look it up.
|
03-16-2015, 04:18 AM
|
Member
|
|
|
Join Date: Feb 2014
Location: Tuscarawas County, Ohio!
Posts: 423
Likes: 393
Liked 222 Times in 148 Posts
|
|
Try moving the slide stop up and down while pushing on the right hand side of the pin. Maybe even pushing it towards the front of the frame. I can get mine to pop out in about 15-20 seconds. The hole in the slide stop is hung up in the shallow groove cut into the trigger pin. I'll be installing my Apex spring kit when I get home from work today...
L8R,
Matt
__________________
SD40-VE owner and proud of it!
|
The Following User Likes This Post:
|
|
03-16-2015, 06:59 AM
|
|
US Veteran
|
|
|
Join Date: Aug 2013
Location: San Antonio
Posts: 285
Likes: 122
Liked 106 Times in 68 Posts
|
|
Do you have the sear assembly unpinned and pulled up and out of the frame? This will relieve the tension from the trigger return spring and make it a lot easier to remove the trigger pin. As AnthemBassMan said, wiggle the slide stop/release around to free it from the groove that it rests in on the pin while pushing the pin with a punch. It should eventually find the sweet spot in the hole on the slide stop/release and push on out,
The labeling on your picture is almost correct except for two things. The u-shaped part is actually steel reinforcement molded in the frame for the rails and the part that you are referring to as the magazine release spring is actually the slide stop/release spring.
Bill
__________________
Remember the Alamo!
|
03-16-2015, 11:52 AM
|
Member
|
|
|
Join Date: Jul 2014
Posts: 287
Likes: 3
Liked 135 Times in 90 Posts
|
|
Quote:
Originally Posted by brchambersjr
Do you have the sear assembly unpinned and pulled up and out of the frame? This will relieve the tension from the trigger return spring and make it a lot easier to remove the trigger pin. As AnthemBassMan said, wiggle the slide stop/release around to free it from the groove that it rests in on the pin while pushing the pin with a punch. It should eventually find the sweet spot in the hole on the slide stop/release and push on out,
The labeling on your picture is almost correct except for two things. The u-shaped part is actually steel reinforcement molded in the frame for the rails and the part that you are referring to as the magazine release spring is actually the slide stop/release spring.
Bill
|
You are also confused about the slide lock. What you have labeled as the slide lock is actually the take down lever. Perhaps just semantics, but it is possible that you need to revisit how everything actually works prior to disassembling it. That understanding is vital to correct reassembly.
|
03-16-2015, 02:48 PM
|
Member
|
|
|
Join Date: Aug 2014
Posts: 70
Likes: 2
Liked 21 Times in 14 Posts
|
|
I tried wiggling everything except twerking
Quote:
Originally Posted by AnthemBassMan
Try moving the slide stop up and down while pushing on the right hand side of the pin. Maybe even pushing it towards the front of the frame. I can get mine to pop out in about 15-20 seconds. The hole in the slide stop is hung up in the shallow groove cut into the trigger pin. I'll be installing my Apex spring kit when I get home from work today...
L8R,
Matt
|
I think that I'm going to once again retry the conventional methods, then follow that up with more wiggling and jiggling. If nothing moves, then it's off to spray some Break Free, Silicone spray, or Deep Creep on the pins and let it soak in and around it.
As a last resort, I'll do what I was tempted to do - that being to use a small, needle-nose pliers with gorilla taped on its ends to bend the curled end of the spring enough to clear the pin - but not so much as it cannot be reattached and bent back.
Worthy of note is that Apex Tactical's YouTube video is working on an SD9 and NOT an SD9VE. THere are notable differences between the two.
I had no trouble popping out the rear pin holding the sear housing - pulling the sear housing up and out was also fairly easy - but not replacing it.
It would be so nice to know where and on top of what the housing sits. Is there a groove on the inside or a platform into which the housing slides?
I did manage to wiggle it back in, BTW.
|
03-16-2015, 03:20 PM
|
Member
|
|
|
Join Date: Aug 2014
Posts: 70
Likes: 2
Liked 21 Times in 14 Posts
|
|
Check my labeling. Then check Glock's. Methinks you're the confused one
Quote:
Originally Posted by JWH321
You are also confused about the slide lock. What you have labeled as the slide lock is actually the take down lever. Perhaps just semantics, but it is possible that you need to revisit how everything actually works prior to disassembling it. That understanding is vital to correct reassembly.
|
As per my first annotated image, I knew it was the spring for the slide release, but don't know why I called it a magazine release (other than I had just talked about ambidextrous mag releases elsewhere).
Also, I searched but could not find an exploded diagram of the SD9 VE and did not know that the red U-shaped metal is a frame support. Thanks for that info.
Now, as per JWH321's comments, I certainly found plenty of Glock exploded diagrams that call our takedown lever a "slide lock," and I do believe the takedown video also makes mention of the different labels used for the same object.
SO, what does GLOCK call the takedown lever (Part #21)?
And, what does GLOCK call the leaf spring under the takedown lever (Part #20)?
Alrighty then. Here's my corrected annotations of the TAKEDOWN LEVER and the U-SHAPED FRAME SUPPORT:
Last edited by PeterPocket; 03-16-2015 at 03:22 PM.
Reason: typo
|
03-16-2015, 03:20 PM
|
Member
|
|
|
Join Date: Feb 2014
Location: Tuscarawas County, Ohio!
Posts: 423
Likes: 393
Liked 222 Times in 148 Posts
|
|
Just finished replacing all of the springs about a half hour ago. Everything went smooth. I'm uploading a short video right now on how to remove that little bugger of a trigger pin. The entire video is 53 seconds long. I had the rest of the springs replaced in about 10-15 minutes. I'll post the video link as soon as it's done. You'll see me push the slave pin through, then stop before the trigger pin fell out. I stopped because I though it was gonna shoot out and hit my laptop screen.
L8R,
Matt
__________________
SD40-VE owner and proud of it!
|
03-16-2015, 03:23 PM
|
Member
|
|
|
Join Date: Feb 2014
Location: Tuscarawas County, Ohio!
Posts: 423
Likes: 393
Liked 222 Times in 148 Posts
|
|
Here you go. Try following this. Well at least without the slow country boy talk, that is!
https://youtu.be/bkDzjypJ_ys
L8R,
Matt
__________________
SD40-VE owner and proud of it!
|
03-16-2015, 04:07 PM
|
|
Member
|
|
|
Join Date: Dec 2014
Location: Oklahoma
Posts: 951
Likes: 682
Liked 301 Times in 210 Posts
|
|
Trigger pin
Quote:
Originally Posted by AnthemBassMan
Just finished replacing all of the springs about a half hour ago. Everything went smooth. I'm uploading a short video right now on how to remove that little bugger of a trigger pin. The entire video is 53 seconds long. I had the rest of the springs replaced in about 10-15 minutes. I'll post the video link as soon as it's done. You'll see me push the slave pin through, then stop before the trigger pin fell out. I stopped because I though it was gonna shoot out and hit my laptop screen.
L8R,
Matt
|
The video looks great. I'm confused about what the slide stop/barrel stop/takedown lever has to do with the trigger pin.
Also, what did you do to the trigger pin to make it slide out when you thought it was stuck so much that you couldn't get it out with a hammer and drift pin?
(About the stop terminology, whatever anyone else calls it, I consider it a barrel stop, since that is what the barrel engages when it returns to battery. Just me, no objection to whatever anyone else calls it. NDZ Performance calls it an "Extended Slide Lock Lever, Stainless Steel". I checked out "Extended" by measuring the new one and the factory one, and the Extended one is only 1mm longer but it makes a great difference in taking the gun down for my cold-dead-fingers.)
|
03-16-2015, 04:18 PM
|
Member
|
|
|
Join Date: Feb 2014
Location: Tuscarawas County, Ohio!
Posts: 423
Likes: 393
Liked 222 Times in 148 Posts
|
|
The take-down/slide stop/barrel stop/whatever you call it lever doesn't have anything to do with taking the trigger pin out. The slide release lever, on the other hand, has a lot to do with holding onto that pin. The lever you use to release the slide after locks back after firing the last round. As for getting the pin the rest of the way out, I just kept working the slide release lever. Working it around in every direction while keeping pressure on the slave pin from the kit. You eventually get it to hit that spot where it will just pop right out. I've also looked at those extended levers to help with field stripping. Haven't made the jump for one yet, but they do look like it would make it easier...
L8R,
Matt
__________________
SD40-VE owner and proud of it!
|
03-16-2015, 04:51 PM
|
|
Member
|
|
|
Join Date: Dec 2014
Location: Oklahoma
Posts: 951
Likes: 682
Liked 301 Times in 210 Posts
|
|
Quote:
Originally Posted by AnthemBassMan
The take-down/slide stop/barrel stop/whatever you call it lever doesn't have anything to do with taking the trigger pin out. The slide release lever, on the other hand, has a lot to do with holding onto that pin. The lever you use to release the slide after locks back after firing the last round. As for getting the pin the rest of the way out, I just kept working the slide release lever. Working it around in every direction while keeping pressure on the slave pin from the kit. You eventually get it to hit that spot where it will just pop right out. I've also looked at those extended levers to help with field stripping. Haven't made the jump for one yet, but they do look like it would make it easier...
L8R,
Matt
|
Thanks - I remember in some videos the reference to the slide lock lever which has a long U-shaped spring that connects to the same pin as the trigger spring pin. I was just confused by the various references to the "takedown lever".
I noticed the exploded view of the Glock because I has posted a reference to it, or a related model, pointing out that there were two plastic tubes associated with the striker. Someone had taken the striker assembly apart and ended up with an extra tube that is actually not shown in a related Apex video.
Last edited by ou1954; 03-16-2015 at 04:54 PM.
Reason: Add comment
|
03-16-2015, 07:04 PM
|
|
US Veteran
|
|
|
Join Date: Aug 2013
Location: San Antonio
Posts: 285
Likes: 122
Liked 106 Times in 68 Posts
|
|
No degradation intended by my comments, just enlightenment. I have learned a lot of useful info from this forum so I wanted to pass it on.
Bill
__________________
Remember the Alamo!
|
The Following User Likes This Post:
|
|
03-16-2015, 07:30 PM
|
Member
|
|
|
Join Date: Dec 2012
Location: PA.
Posts: 607
Likes: 440
Liked 121 Times in 94 Posts
|
|
Quote:
Originally Posted by ou1954
The video looks great. I'm confused about what the slide stop/barrel stop/takedown lever has to do with the trigger pin.
Also, what did you do to the trigger pin to make it slide out when you thought it was stuck so much that you couldn't get it out with a hammer and drift pin?
(About the stop terminology, whatever anyone else calls it, I consider it a barrel stop, since that is what the barrel engages when it returns to battery. Just me, no objection to whatever anyone else calls it. NDZ Performance calls it an "Extended Slide Lock Lever, Stainless Steel". I checked out "Extended" by measuring the new one and the factory one, and the Extended one is only 1mm longer but it makes a great difference in taking the gun down for my cold-dead-fingers.)
|
He was'nt the one who had problems taking it out.
It was the O.P.
3
|
03-16-2015, 09:26 PM
|
|
Member
|
|
|
Join Date: Dec 2014
Location: Oklahoma
Posts: 951
Likes: 682
Liked 301 Times in 210 Posts
|
|
Lost rack
Quote:
Originally Posted by 3hounds
He was'nt the one who had problems taking it out.
It was the O.P.
3
|
I lost track along the way. I'll have to go back and review this thread.
|
05-25-2015, 06:25 PM
|
Member
|
|
|
Join Date: Feb 2013
Location: Stillwater OK
Posts: 10
Likes: 3
Liked 12 Times in 4 Posts
|
|
Trigger Pull Liability & short firing pin
The last 3 new pistols I have purchased all required longer firing pins to pop hard primers. When longer firing pins were installed on at least 2 of them lighter hammer springs were required as part of the package. This reduced both the double and single action trigger pull of CZ-75's.
While no one comes right out and says it I am pretty sure the shorter firing pins are installed to be sure the gun can pass California's drop test. When their new from the box they also fail to set off some hard American and European primers on brand name Ammo. It's not a really deadly fault in my case as I only buy revolvers and and simi-autos that are true double actions. The light strikes almost always goes bang on the second or third pull of the trigger.
Hearing the gun go click when you pull the trigger at the range is a frighting sound having it happen in a gunfight could be deadly to me. I may not be able to sort through the ammo available on short notice so I make sure every pistol I carry will work with ammo loaded using the hardest rifle primers I can find.
I don't carry hand-loaded ammo. All my pistols have over 6 pound double action trigger pulls. The single action pulls are all over 3.5 pounds. I have a Dan Wesson 357 revolver that new to me and hasn't had the trigger tuned yet. I has an awfully light single action trigger and is rather heavy to carry. I am not sure how I will set that trigger. I know it will be over 6 pounds double action.
I have been shooting 2 and 3 pound single action trigger for 60 years and anything less then 3 pounds has no place on anything but a target or set trigger gun. Three pound triggers need some take up to let you know what your doing.
GC
"Guns are a lot like parachutes ~ If you need one and don't have one, you'll probably never need one again".
|
05-27-2015, 08:51 AM
|
|
Member
|
|
|
Join Date: Nov 2007
Location: The Alamo!
Posts: 1,172
Likes: 578
Liked 378 Times in 174 Posts
|
|
There's no controversy on my gun, it's stock and works fine.
__________________
SD9VE, American perfection!
|
The Following 4 Users Like Post:
|
|
05-27-2015, 11:31 AM
|
|
Member
|
|
|
Join Date: Apr 2013
Location: WA state
Posts: 52
Likes: 12
Liked 8 Times in 5 Posts
|
|
I had the Apex trigger and springs installed but I re-installed all stock springs keeping the AEK trigger which I like much better. I've had just 2-3 minor issues over the 2+ years/~1k various rounds through it, but now it will fall apart since I jinxed it by mentioning anything...
|
10-11-2015, 09:50 AM
|
Member
|
|
|
Join Date: Oct 2015
Posts: 1
Likes: 0
Liked 0 Times in 0 Posts
|
|
I just bought the sigma and was looking for the trigger mod or even removing the extra spring like most have done, but it appears mine does not have that style spring kit in it, it only has 1 spring in the back unlike the kits I have seen. Is this something SW has done to keep from being changed?
It looks like this
|
10-29-2015, 09:06 AM
|
Member
|
|
|
Join Date: Oct 2014
Posts: 257
Likes: 44
Liked 170 Times in 67 Posts
|
|
I run an Apex kit, polished the trigger parts with a Dremel and Mother's Mag polish (Glock $.25 trigger job), installed an M&P rear sight, epoxy coated the slide black, added a Pachmayr grip sleeve, and run a light on mine. I love this gun. I do. And I own a G17 that I use for IDPA but there is just something about the feel of this SD9VE.
|
The Following User Likes This Post:
|
|
10-29-2015, 10:15 AM
|
|
Member
|
|
|
Join Date: Apr 2015
Posts: 290
Likes: 14
Liked 197 Times in 123 Posts
|
|
I also installed the Pachmayr slide on grip and find that it rotates around after I fire the gun at the range. I took it off and used alcohol on the grip and gun but that didn't seem to help. Do you have any issue with it rotating ?
Norm
|
10-31-2015, 07:39 AM
|
|
Member
|
|
|
Join Date: Apr 2013
Location: WA state
Posts: 52
Likes: 12
Liked 8 Times in 5 Posts
|
|
Quote:
Originally Posted by dwcopple
I run an Apex kit, polished the trigger parts with a Dremel and Mother's Mag polish (Glock $.25 trigger job), installed an M&P rear sight, epoxy coated the slide black, added a Pachmayr grip sleeve, and run a light on mine. I love this gun. I do. And I own a G17 that I use for IDPA but there is just something about the feel of this SD9VE.
|
I've been mulling about how to make my slide blackish ever since I got mine a few years ago, I gave up looking for an orphaned SD9 slide on ebay. Is that Rust-oleum Appliance Epoxy you used? I've read many good things about it and have actually coated a few of my stainless knife blades putting a light dusting of etching primer on first then heating before coating...both done several months ago and look great and seem very tough, not cracking or peeling when I sharpened them at all. Probably will try this method on mine soon.
|
11-01-2015, 09:56 AM
|
Member
|
|
|
Join Date: Oct 2014
Posts: 257
Likes: 44
Liked 170 Times in 67 Posts
|
|
|
The Following User Likes This Post:
|
|
11-02-2015, 03:22 AM
|
|
Member
|
|
|
Join Date: Oct 2015
Location: Oregon
Posts: 45
Likes: 45
Liked 21 Times in 13 Posts
|
|
I had to also replace the slide take down lever with a longer one as I also had a terrible time with the shorter stock one getting it to release the slide
|
11-02-2015, 04:30 PM
|
|
Member
|
|
|
Join Date: Oct 2008
Location: Denver, CO
Posts: 1,814
Likes: 167
Liked 979 Times in 490 Posts
|
|
Long thread, but the bottom line for me is that I have replaced the springs in several pistols, resulting in a smoother and/or crisper trigger. I never touch the striker spring, and just live with whatever trigger pull I wind up with. I want a loud bang every time I pull the trigger.
Last edited by scattershot; 11-02-2015 at 06:25 PM.
|
11-02-2015, 10:21 PM
|
|
Member
|
|
|
Join Date: Apr 2013
Location: WA state
Posts: 52
Likes: 12
Liked 8 Times in 5 Posts
|
|
Quote:
Originally Posted by dwcopple
yes, Rustoleum Appliance Epoxy. Dust the last coat from around 18-24" to flatten the sheen. Awesome stuff. I baked it in a toaster oven for an hour after the final coat. Tough as nails. No primer required or advised.
|
Sounds good, I was wondering about how to make sure it didn't get too glossy. I don't like rubbery grips as much as gritty grips, I've been using a roll of 3M tread tape and making my own grip patterns, you don't need much. It just needs to be in the right places.
|
11-03-2015, 12:37 AM
|
|
Member
|
|
|
Join Date: Aug 2015
Location: SW Indiana
Posts: 1,029
Likes: 1,103
Liked 1,035 Times in 467 Posts
|
|
After reading Massad's article. Don't know why anyone would mess with the internals of their firearms. Jeez.
Heck I'm afraid that my cerakoted sd9ve's would be considered tactical - negligent error induced paint, after reading his article.
|
11-04-2015, 10:53 AM
|
Member
|
|
|
Join Date: Sep 2012
Posts: 325
Likes: 36
Liked 102 Times in 68 Posts
|
|
Quote:
Originally Posted by madracr07
Now I am second guessing having the apex spring kit and trigger installed in mine yesterday. I paid $81.00 to have it done, and it feels great when I dry fired it. I am planning on trying it out tomorrow, as we are having my birthday party at the shooting range, and we are expecting 40 people with guns.
I truly hope I didnt screw mine up. I will have to pay someone else to put it back together again.
|
Don't worry about it . The Trigger kit from Apex is Carry/duty certified.
From the Masad Ayoob post above. Granted they are talking about glocks however the Apex duty/carry kit and AET trigger still only drops the SD trigger into the 6 LB range.
"That will generally be determined by manufacturer spec for “duty trigger” pull weight, and “common custom and practice” WITH THAT PARTICULAR FIREARM. With the popular Glock, the manufacturer’s position is that the nominal 5.5-lb. pull weight of the standard model is minimum for duty"
Last edited by EBK; 11-04-2015 at 11:06 AM.
|
|
Posting Rules
|
|
|
|
|