Smith & Wesson SW22 Victory

garryj

Member
Joined
Sep 12, 2016
Messages
37
Reaction score
81
Location
Pensacola, FL
I recently got this Smith & Wesson SW22 Victory .22LR since I already had thousands of rounds of .22LR ammo. The fact that .22LR ammo is MUCH less expensive than 9mm, .45ACP or .38 Super (the other calibers I regularly shoot) also contributed to this decision. The version I got has a stainless steel frame, slide and barrel. Other features are 5.5” threaded match grade bull barrel, green front and rear fiber optic sights and it came with two 10-round magazines and a picatinny rail. In this standard configuration, the accuracy was great. I did have a very frustrating problem on my first two range trips with it. I kept getting stovepipes and sometimes the spent case didn’t even make it out of the ejection port at all. A little research online and I knew to adjust the ejector. The first adjustment attempt resulted in slightly better ejection, but I was still getting a lot of stovepipes. My second attempt resulted in much better ejection and very few problems. I have since found the sweet spot for the ejector and can attribute all malfunctions to the cheap and very old ammo or operator error.

Takedown for cleaning is achieved by removing one screw just forward of the trigger guard. Once the barrel/receiver are removed from the frame, the slide can be removed by pulling it rearward out of the receiver. If you want to remove the barrel from the receiver, remove another screw below the forward part of the receiver and pull the barrel forward. (This ease of takedown and aftermarket parts replacement also contributed to my decision to buy this firearm).

Not being one to leave well enough alone, I started making “improvements” to the gun. First, I replaced the grips with Tandemkross Hive grips, and then their Game Changer muzzle brake. I then added the Truglo reflex sight and finally the Tandemkross Victory trigger. The Tandemkross Victory trigger was far from the easy install touted on their websight (at least for me with my bigfoot sized hands). I wound up losing the spring and detent and had to order another set from Tandemkross (I actually ordered two to be safe). I eventually got the trigger in, but not before losing another spring and detent. I did eventually find one spring and both detents I had lost. It was well worth the trouble because this trigger is phenomenal. The standard trigger is good, but the trigger pull went from an average of 2lbs 11 oz to 1lb 3oz. The best part is the ability to adjust pre and over travel to whatever is comfortable for you.

These are the groups I got on my last range trip with 10 year old Remington bulk ammo. Both targets were at 15 yards 25 rounds on the large target and 10 on the smaller one.

Garry
 

Attachments

  • SW22RDL.JPG
    SW22RDL.JPG
    157.4 KB · Views: 39
  • SW22RDR.JPG
    SW22RDR.JPG
    157.2 KB · Views: 30
  • DSC00315.JPG
    DSC00315.JPG
    254.4 KB · Views: 28
  • DSC00319.jpg
    DSC00319.jpg
    78.4 KB · Views: 28
Register to hide this ad
I eventually got the trigger in, but not before losing another spring and detent. I did eventually find one spring and both detents I had lost.

Secret I learned long ago. Disassemble/reassemble gun inside a plastic bag to prevent small springs from flying into the perfect hiding places. I've gotten too old to be crawling around on the floor looking for some spring which decided to leave the work area.
 
I think I would have been fine with the 3#ish trigger pull. I had a revolver with a 1.5# trigger pull once and frankly it was a little scary. It kept going off when I didn't expect it.

After reading your review I've come to the conclusion that the Victory is sort of a cross between a Ruger and a High Standard. Interesting.
 
After reading your review I've come to the conclusion that the Victory is sort of a cross between a Ruger and a High Standard. Interesting.
One of the main reasons I chose the Victory over the Ruger MKIV was the availability of after market upgrades from Tandemkross and Volquartsen. The lower cost was just a bonus.

Garry
 
I did much the same upgrades to my own Victory, but added the VQ carbon fiber barrel and a FF3 on the Maddmacs base. Sadly, the gun's design makes it a rather tedious task to clean after a few hundred rounds suppressed. This will be the first pistol to leave the herd shortly. The replacement MKIV 22/45 Lite has received the VQ accurizing kit and awaits the titanium can being released from jail.
 
Back
Top