MAG-NUM
Member
Guess these were priced too high but I have a lot of time in making them. 
How about $50.00 plus a flat $6.00 for Priority shipping.
A good friend of mine asked me to make a stand to hold his Presentation Cases so while I was building one for him, I decided to build a few more.
They are made from beautiful solid American Red Oak.
Offered in either dark stained or natural finish with two coats of hand rubbed Tung oil applied followed by
a 0000 steel wool rubdown and a coat of paste wax.
Complete with felt feet and lid protectors.
This is a custom built folding display stand to fit the Smith & Wesson wooden Presentation cases used from the late 1960s thru
the mid 1980s and will hold cases from the 3.5" to 8 3/8" barrel lengths, but may fit any clam shell type presentation case that
measures no more than 7 7/8" front to back and 3" top to bottom.
Proudly display your Smith & Wesson revolvers at just the right viewing angle. Great for the gun room or as a photography aid.
Just the setup for gun shows and dealer displays, your guns will stand out from all the others.
Natural or Golden Oak colored stand holding a case with an 8 3/8" Model 57 from 1980.
Dark stained stand holding the small sized Presentation case used with 3 1/2" & 4" barrel guns. Model 29-2 shown.
Detail shot showing the folding lid holder in the open position.
There are 4 Natural or Golden Oak colored and 4
Dark stained. Dark stains vary in color from reddish brown to light walnut color.
There is quite a bit of time in machining, sanding, staining and finishing so I am asking $75.00 each which includes shipping
in the Continental U.S.A.
First I'LL TAKE IT has color choice of these 8. I have blanks cut for 8 more but the holidays will slow me down a bit.
Email me for details. [email protected]
Thanks for looking and Merry Christmas to all you fine folks! Bob
How about $50.00 plus a flat $6.00 for Priority shipping.
A good friend of mine asked me to make a stand to hold his Presentation Cases so while I was building one for him, I decided to build a few more.
They are made from beautiful solid American Red Oak.
Offered in either dark stained or natural finish with two coats of hand rubbed Tung oil applied followed by
a 0000 steel wool rubdown and a coat of paste wax.
Complete with felt feet and lid protectors.
This is a custom built folding display stand to fit the Smith & Wesson wooden Presentation cases used from the late 1960s thru
the mid 1980s and will hold cases from the 3.5" to 8 3/8" barrel lengths, but may fit any clam shell type presentation case that
measures no more than 7 7/8" front to back and 3" top to bottom.
Proudly display your Smith & Wesson revolvers at just the right viewing angle. Great for the gun room or as a photography aid.
Just the setup for gun shows and dealer displays, your guns will stand out from all the others.
Natural or Golden Oak colored stand holding a case with an 8 3/8" Model 57 from 1980.
Dark stained stand holding the small sized Presentation case used with 3 1/2" & 4" barrel guns. Model 29-2 shown.
Detail shot showing the folding lid holder in the open position.
There are 4 Natural or Golden Oak colored and 4
Dark stained. Dark stains vary in color from reddish brown to light walnut color.
There is quite a bit of time in machining, sanding, staining and finishing so I am asking $75.00 each which includes shipping
in the Continental U.S.A.
First I'LL TAKE IT has color choice of these 8. I have blanks cut for 8 more but the holidays will slow me down a bit.
Email me for details. [email protected]
Thanks for looking and Merry Christmas to all you fine folks! Bob
Last edited:
