Scotch Brite for Stainless Finishes

L

les45

Member
Joined
Dec 18, 2010
Messages
308
Reaction score
13
I had heard about this before, but had never used it until today. I used a gray Scotch Brite pad to clean up an old S&W Model 65 that I had recently bought. The gun was in good shape but had a lot of scuffs and fine marks from years of holstering and handling. I was amazed at the results. The gun looks like brand new with a factory satin finish. The pads are very easy to use and not nearly as much effort as polishing compounds. Just buff in the direction of the grain of the steel, generally parallel to the length of the barrel on all surfaces.
 
Register to hide this ad
They work well, I cleaned up this 629 carry comp with them.
IMG_2929.jpg
 
Be sure to get all the abrasive grit out of areas, believe it or not, those pads put off some minute particles...part of the abrasive process.

I always rinsed in Mineral Spirits after wards, and had better luck with the red pads.
 
Make sure they are the fine grit

They are sevral differrent grit grades avail too much will screw up the finish and leave lines in it , just about got one polished bk out somebody over scotchbrited ( a little goes a long way ) 41steve










les45 said:
I had heard about this before, but had never used it until today. I used a gray Scotch Brite pad to clean up an old S&W Model 65 that I had recently bought. The gun was in good shape but had a lot of scuffs and fine marks from years of holstering and handling. I was amazed at the results. The gun looks like brand new with a factory satin finish. The pads are very easy to use and not nearly as much effort as polishing compounds. Just buff in the direction of the grain of the steel, generally parallel to the length of the barrel on all surfaces.
Click to expand...
 
It's difficult to duplicate a factory job outside of the factory. The grey pads, used with a fine, careful touch will improve a really ugly SS gun. It helps if you have a new/near new SS revolver sitting there so you can see the direction in which the factory worked the finish in various locations. You can overdo the grey pad, making the finish too bright to approximate factory new.
 
The brushed finish is nice, but I prefer the matte beadblast finish, but be beware of the glass bead size, the beads used in road markings are much larger than others, until they break down, it leaves a more pockmarked look.

However not everyone has access to a bead/sand blasting cabinet.
 
Thanks Walter Rego for the link.

I use Happich SimiChrome a premium German polish found at finer motorcycle store [well where I get mine] on my SS revolvers..others use Mother's Mag polish.

I use green Scotch Brite for burned pots..and polishing shotgun chambers in my Cowboy Action guns.

Wouldn't mind watching someone else put a SB pad to their revolvers but visions of cleaning up a scorched pot keep me from doing so.

Will keep WR's link handy..you never know.
 
Old Unk said:
Thanks Walter Rego for the link.

I use Happich SimiChrome a premium German polish found at finer motorcycle store [well where I get mine] on my SS revolvers..others use Mother's Mag polish.

I use green Scotch Brite for burned pots..and polishing shotgun chambers in my Cowboy Action guns.

Wouldn't mind watching someone else put a SB pad to their revolvers but visions of cleaning up a scorched pot keep me from doing so.

Will keep WR's link handy..you never know.
Click to expand...


Keep them ALL handy. They all have their place.

P1010930.jpg
 
Scotch-brite pads have been used for years in the in the custom sheet metal industry. Most restaurant equipment is finished with a red pad which is similar to 120 grit which is an industry #4 finish. That should equate with a typical gun finish but will show a grain. If you8 want more shine, you will probably have to get into compounds.
 
I have been using them with stainless guns for years. They work really well. I guess the secret's out now!
 
The trick to the Scotchbrite pads if you wish to duplicate the factory finish is a light touch and a little bit of gun oil as a lubricant. Wipe clean with a piece of soft cloth often and observe your work. If just touching up minor mars and scratches you can usually see the direction of the grain from the factory finish and just wipe in the same direction. It's not hard to do and feather the area into the original finish. Start with a finer grade and a very light touch and see how it looks before going to anything coarser. And I really think the use of oil helps.
 
Where do you find the pads? My Supermarket carries green, and I don't think I've ever seen the others. TIA
 
LET-CA said:
Where do you find the pads? My Supermarket carries green, and I don't think I've ever seen the others. TIA
Click to expand...

Same here. Went to Ace Hardware and all they had were green.
Also does that Mothers polish make a high gloss finish ? I don't care for the bright nickel/bumper chrome look .
 
You must log in or register to reply here.

Latest posts

Back
Top